Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
38 Cards in this Set
- Front
- Back
Pipe and similar wrenches are justed by the use of a |
Thumb screw |
|
Pipe wrenches use blank to produce the gripping action |
Pressure points 2 or points of contact |
|
Hex keys are available in blank and blank sizes |
Metric and Imperial |
|
The 2 types of hacksaw blades are blank and blank |
All hard and flexible back |
|
Cold chisel are tempered for approximately 20 mm or 3/4 from the blank |
Cutting end |
|
The most commonly use screws in pipe trades are the blank and the blank |
Ordinary slotted and Robertson screwdriver |
|
The tin snips most likely found in your tool Box are blank |
Aviation snips |
|
Most plyers exert pressure on the grasping and through a version of a blank |
1st class lever |
|
An Mj torque wrench exerts a torque pressure of blank on the 5/16th nut of an MJ coupling |
60' lbs |
|
Where does the handle go on a file |
T'ang |
|
The wide rollers found on a pipe cutter help prevent the blank |
Cutter wheel from spiraling along the pipe |
|
The biggest advantage in using a multi will pipe cutter is that it blank |
Allows for the cutting of pipe in tight corners where a 360゚ sweep of the cutter is not possible |
|
The pipe cutter handle Should be turned no more than blank per revolution around the pipe |
1/4 of a turn |
|
List 3 things that can be prevented by reaming a pipe |
Prevent the bore of the pipe from being restricted Causing excessive pressure loss
A Burr may cause turbulent flow in the pipe which can lead to a water hammer condition and cause erosion
A Burr catches materials and creates stoppage in the pipe |
|
Soil pipe cutters are designed to cut |
Cast iron Pipe only |
|
Portable hand drills are Rated by their |
Chuck size |
|
The Three main parts of a drill bit Are |
The shank the body and the point |
|
Hole saws are used when |
The size of the hole to be drilled is larger than the largest practical twist drill size |
|
The 7" grinding wheel in a bench grinder with a wheel speed of 3450 rpm will have an approximate surface travel speed of |
120 km per hour |
|
Portable pipe freezing equipment is designed to freeze |
Stationary water only in selected sections of piping |
|
True or false all electrical extension cords can be used in any application or location explain answer |
False electrical extension cords are available in both indoor and outdoor types distance and power requirements must be taken into consideration |
|
What is the rule of thumb for choosing a pipe wrench for 3/4 inch pipe fabrication |
For sizes up to 3/4 inch nPS use a pipe wrench no larger than a 10" |
|
What wrench would you choose when installing a valve on a pipe project |
Hex wrenches spud wrench open end adjustable wrench |
|
Hex keys are used to tighten and adjust |
Set screws |
|
How can you make a tubing Bender |
By using wire solder rolled around the to being to be bent |
|
The teeth of a hacksaw blade face blank so the cutting is done blank |
Forward and on the push stroke |
|
A hacksaw blade with blank teeth per inch would be used to cut M copper tube |
Thirty two |
|
What should you use to make holes in dry wall |
A keyhole or compass saw |
|
What to measurements are used to determine the size of a cold chisel |
The width of the cutting edge and the overall length of the tool |
|
Files cut only when you blank they are not to be dragged backwards over a work piece because blank |
Push and this procedure breaks the teeth from the file |
|
How can you increase the effectiveness of a hammer |
By gripping the handle close to the end |
|
The hook or Tang of tape measure is loose in order to accommodate |
Inside measurements by allowing for the hook or tang thickness |
|
Blade and straight fluted reamers may be used either blank while a spiral fluted reamer is used blank |
On power vices or by hand and only by hand |
|
What must you remember when choosing to use a drop head dye to thread pipe by hand |
Each size of pipe has its own individual drop head |
|
If the handrill you are to use has a powerful motor what must you do before using the drill |
Make sure you are positioned and anchored so as to minimize the risk of losing control of the drill and causing serious personal injury |
|
You are to drill a hole in a stainless steel countertops sink what are 2 things that you should remember |
Use a titanium alloy bit drill at slow speed |
|
Files are classified by the |
Length shape and cut |
|
Explain why filing is done only in the forward stroke |
Dragging the file backwards will break the teeth from the file |