Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
40 Cards in this Set
- Front
- Back
Who is responsible for the certification of propane cylinders in Canada? |
Transport Canada |
|
What is the minimum rated working pressure for a propane cylinder? |
240 psi |
|
What is the maximum filling density of a propane cylinder based on weight? |
42% of the WC |
|
Who is responsible to ensure that a propane cylinder is not overfilled? |
The person who fills the cylinder |
|
How many cylinders (maximum) can be connected together, and installed against the wall of a building for propane fuel supplied to the building? |
4 |
|
How often must a propane cylinder be recertified? |
Every 10 years |
|
When transporting a propane cylinder, what position must it be in? |
Secured with the relief valve, communicating with the vapour space |
|
What is the tare weight of a cylinder? |
The weight of the cylinder when empty |
|
What is the purpose of a spit valve on a propane cylinder? |
To determine when the cylinder is full |
|
What is the purpose of an OPD? |
To prevent the cylinder from being overfilled |
|
When is it necessary to install an excess flow valve on a cylinder used on a construction site? |
On all cylinders over 1 pound propane capacity |
|
When is a plug or cap required in the valve of a propane cylinder? |
When the cylinder is less than 45 pounds of propane capacity |
|
What is the maximum size of bleed opening in a spit valve? |
A number 54 orifice drill size |
|
What is the minimum distance that combustibles must be kept clear of a propane container? |
10 ft |
|
The requirement is that there must be a minimum distance of____ ft from any tank, __ft from the property line and ___ft from any source of ignition |
10ft 25ft 25ft |
|
It is illegal to fill any propane, container tank or cylinder in excess of how much volume? |
80% of its volume |
|
Testing an excess flow valve in the summer when pressures are high, will not prove what? |
That the valve will also function under low pressure conditions in the winter |
|
What is the WC of a propane cylinder? |
Weight of water the cylinder can hold when full |
|
In the specifications CTC 4BA240 what does the 240 stand for? |
Minimum rated working pressure |
|
What must be done to a new cylinder before it can be filled? |
It must be purged of moisture and air |
|
When a propane, vent line, discharges, vertically upwards, what is required on the outlet end ? |
A loose fitting cap |
|
Where should a relief valve on a propane cylinder be located? |
So that communicates with the vapour space at all times |
|
What is the purpose of the fixed liquid level gauge?( spit valve ) |
To determine when the maximum filling density is reached |
|
What is the minimum distance between a cylinder relief valve, and a building opening below the relief valve? |
3feet |
|
What is the maximum size propane cylinder that may be used indoors without permission from the authority having jurisdiction? |
5 pounds |
|
What is the significance of theQ-CC1 propane cylinder valve over the standard POL valve ? |
It has an excess flow valve |
|
Separate filler valves have two backcheck valves incorporated into them. One is a metal to metal seat. What is the other check valve seat? |
Neoprene to metal |
|
On construction sites, what is required to be used with all propane cylinders, larger than 1 pound propane capacity? |
An excess flow valve |
|
What is the purpose of the bypass hole in the excess flow valve? |
To allow the valve to return to its open position |
|
How frequent should an excess flow valve be tested? |
When it’s installed and annually after that |
|
Why is an excess flow valve installed? |
To control the flow of propane, in case of a line rupture or breakage |
|
The smallest cylinder has 1 pound of propane capacity, and the largest cylinder has____ pounds of propane capacity |
420 pounds |
|
Prior to being called transport Canada the organization was called the Canadian transport commission, and prior to that it was called the what? |
Board of transport commissioners |
|
Cylinders made in the US are certified through who? |
Department of transport, or the interstate commerce commissioner |
|
The length of a hose used to connect a construction heater to a cylinder is how long? |
Minimum 15 feet and maximum 75 feet long |
|
How is an excess flow valve sized? |
So that it will allow 50% more flow than the maximum expected flow rate |
|
If the excess flow valve is installed on a liquid line a _______ is required upstream of the excess flow valve |
Strainer |
|
_______ valves will be needed to clean the strainer without draining the entire propane system |
Isolation |
|
How must cylinders be painted? |
Powder coated with colours that are light and reflective |
|
How much BTUs per pound of propane does it take to cause vaporization without raising the temperature of the propane liquid? |
54 btus per pound |