Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
85 Cards in this Set
- Front
- Back
How many FCF profiles are there?
|
A
B C D E F G |
|
Explain how oil consuptmion is figured.
|
Oil consumtion can't exceed 44.8 oz of oil per flight hour(oz of oil consumed divided by flight hours). If it does initiate a downer, service and perform penalty run IAW MIMs
1QT=32oz |
|
What is the project Pri for TDs?
|
ZO9-05
|
|
What is the project Pri for NMCS?
|
706-02
|
|
What is the project Pri for High time components?
|
ZA9-05
|
|
What is the project pri for OOR?
|
730-02
|
|
What is the project Pri for PMCS?
|
707-02
|
|
WHat is the project Pri for an up gripe?
|
AK1-05
|
|
When are compass calibrations required?
|
After flux valves are changed or when maintenance is performed on the system.
|
|
How often is a Flux valve inspection performed?
|
every 365 days, because ATC said so.
|
|
When is a compass in flight verification required?
|
The flight following compass cal or flux valve inspection.
|
|
What is the Type maintenance / when discovered code for an FCF?
|
P/B
|
|
What is FAD?
|
Force Activity Designator. It determines your priority for receiving parts.
|
|
What is the SF44, and what is it used for?
|
The "cadillac chit". Used for
Fuels Oils Lodging Officer/Enlisted Transportation MISC |
|
How long is a daily good for?
|
72 hours, or 24 hours commencing from the First take off of the day
|
|
How long are fuel samples good for?
|
24 hours
|
|
Where can you find the Intra-Navy advice codes?
|
the NAVSUP P-409
|
|
What is the OPNAV 4790/141?
|
The "A" Sheet.
|
|
What are the limits and +/- for Engine efficiencies?
|
Not below 95%, Not to exceed 108%. +/- 3%
|
|
What weight constitutes a heavy weight landing?
|
103,880-114,000
|
|
What weight constitutes an overweight landing?
|
above 114,000 or 10 heavy weights.
|
|
What is the OPNAV 3710/4
|
The NAVFLIR
|
|
What EOC is assigned to an aircraft with one INS gripe?
|
C (1 System in nav mode)
K (1 System inop) |
|
What EOC is assigned to an aircraft with 2 down INS systems.
|
Z
|
|
What EOC if any is assigned to a conditional inspection?
|
Z
|
|
What ISIS requires an FCF?
|
ISIS C or Phase D
|
|
What constitutes an idle prop? What must be done?
|
a prop that hasn't turned for at least 3 revolutions in 56 days. You must perform a 56 day conditional.
|
|
What happens if a prop remains idle for more than 56 days?
|
You must perform an on the wing Eddy current inspection.
|
|
When do you perform a fuel system contamination inspection?
|
When 25% of the total fuel baffles have been removed from any fuel tamk, or 40 flight hours after new foam installation
|
|
What is an 1800 hr inspection, and when is it performed?
|
It's an engine oil change. Performed the next ISIS inspection.
|
|
When are Nacelle inspections required? Who gets them?
|
When an engine has been removed. AMs, ADs, AEs
|
|
List 10 Conditional inspections
|
Acceptance
Transfer Structural Lightning strike Bird Strike Excessive air speed w/ flaps, landing lights, turret or gear extended. Hail storm Jammed flight controls Engine inspection Over torque Over Speed Over temp Chips light 1800 hr Nacelle insp Prop balance Prop dome reseal 25 hr prop filter Fuel contamination Flux valve 14 day rinse Static discharger insp |
|
What conditions make it necessary to perform a prop balance?
|
New Prop
Front or Rear cone seat replacement. Blends greater than .5 Non symmetrical paint application Spinner Change Heater replacement Cuff repair Changing from erosion tape to sealant RGB mount Excessive Prop vibe Replacement of elec contact ring |
|
How long do you have to perform a prop balance?
|
25 hours initially.
An additonal 25 hours can be granted by the CO. 25 more hours may be granted by the TYCOM. |
|
What are the max operating hours for the GTCP-95-2?
|
3000 starts
|
|
What are the max operating hours for the GTCP-95-3?
|
4500 hrs
|
|
What are the max operating hours for the GTCP-95-10?
|
Until failure.
|
|
What parts require wing approval for cannibalization?
|
Major Hyd components
QEC assemblies CADs Fire extinguishing components O2 System components |
|
What is the OPNAV 5442?
|
The MESM. Mission essential, sub-system matrix
|
|
Where in the A/C Logbook are TDs listed?
|
List 2 - TDs not incorperated
List 4 - TDs already incorperated |
|
What must you do in the event of an aircraft mishap?
|
Notify the CDO
Lockdown OOMA Collect all W/C Logbooks, and lock them up along with the ADB. Notify MO, MMCO, MMCPO Activate Emergency rec team. |
|
What limits are listed on the Daily, and what are they?
|
O2-1600
Tires- Nose-150lbs Main-170lbs Hyd systems- 1-5.6 2-1.0 EBB-1900 Brake accum-800 +/-25 EDC-Full |
|
What inspection deviations are authorized?
|
+/- 3 days for calendar inspections. Next cycle occurs as normal.
+/- 10% for inspections based on hours, cycles or events. Fractional deviations get rounded down. One time deviations can be granted from the wing for operational commitment or A/C ferry |
|
What is the Type Maint/When Discovered code for a discerepancy found on a daily?
|
J/D
|
|
Who releases an aircraft when there has been a missing tool?
|
The Maintenance Officer.
|
|
What is the supply status BB?
|
Back order
|
|
What is the supply status BD?
|
Being Delayed
|
|
What is the supply status BM?
|
Passed off station
|
|
What is the supply status BA?
|
In process for shipment
|
|
WHat is the supply status BZ?
|
Looking for manufacturer to make part
|
|
Who can authorize turns in inclimate weather?
|
The Maintenance officer
|
|
Who can authorize Man on the stand turns at night?
|
Maintenance Officer
|
|
If a jammed flight controls gripe cannot be duplicated, what MUST happen.
|
A log book entry
|
|
How long are Release and Control checks good for?
|
72 hours
|
|
What is the 4790/25a
|
The misc/history section of Logbook
|
|
What type of inspection is a 200 hour and what does it entail?
|
It's a special, and it's an engine wash (B&Bs).
|
|
What must happen when a Sync box is removed?
|
FGPL checks on all four engines.
|
|
What FCF Profile is performed for a 30 day no fly?
|
G
|
|
What is FCF A for?
|
Engine, or RGB
|
|
What is FCF B for
|
Fuel control, Mechanical rigging
|
|
What is FCF C?
|
Prop, Prop control, valve housing
|
|
What is FCF D?
|
Flight controls
|
|
What is FCF E for?
|
ISIS C or Phase D
|
|
What is FCF F for?
|
Acceptance, Post PDM/SDLM, Both FDIs, More than 2 attitude sources, Nav J box, or altering of 106/107 cards
|
|
When must a 1200 hour (prop dome reseal) be done.
|
Whenever a prop dome is removed. verify in the prop log book weather or not 1200 hrs since last conditional have been exceeded.
|
|
If prop dome is removed, but PRC-125 is not incorperated, and 1200 hour is not exceeded then...
|
Cut one time conditional to the mechs to "perform prop dome reseal conditional IAW PMIC" Sign off should read, prop hours remaining_____. Reseal not required, Blade segment gear inspection complete.
|
|
If prop dome is removed, and PRC-125 is not incorperated, and 1200 hour has been exceeded then...
|
Cut Maf using inspections due section of OOMA, "pre-PRC 125 prop dome".
Cut Work request to MALS for reseal. Upon return, Verify PRC-125 installed, provide logs and records with TD MAF from MALS. Sign off, make sure Blade segment gear inspection is done. |
|
If prop dome is removed, and PRC-125 is incorperated then...
|
Cut MAF using inspections due section of OOMA "Blade segment gear inspection".
Sign off. |
|
What does the * in the PMIC mean?
|
There is an SRC (Scheduled removal component) card associated with that component.
|
|
If there is a broken knob on the flight station CDNU, what do you need on the in process.
|
A fod free from QA because it's in the flight station.
|
|
Are deviations allowed for conditional inspections?
|
NO
|
|
What needs to be issued when there is a prop leak?
|
A propeller and control leak check conditional.
|
|
How many attitude sources on a P-3, and what are they?
|
4, INS1, INS2, STBY Gyro, Peanut Gyro.
|
|
Can you fly an FCF in conjunction with a mission?
|
Yes, only if approved by the CO, and the FCF has to be complete, and logged on the checklist, before conducting the mission.
|
|
How often are ISIS done?
|
Every 224 days.
|
|
If engines have been running, how long do you have to wait before performing B&Bs?
|
until TIT reads 70C
|
|
What does the * in an FCF deck mean?
|
The step marked with an * can only be checked in flight.
|
|
How many maintenance actions require a logbook entry and what are they?
|
5. R&R flux valve, R&R Landing gear, R&R Hyd pump, R&R major Hyd assembly, jammed flight controls
|
|
When must you perform a 25 hour prop filter inspection, and what are the stipulaitons?
|
It is performed after a control, pump housing, new or repacked dome is installed. Prop filters are inspected no sooner than 25 hours, but no later than 50.
|
|
What MAFs do you cut for an engine change?
|
220-Electrical disconnect
110-remove prop (prop control attached) 220-Remove Generator(engine 2,3,4) 110-Remove EDC(engine 2,3) Conditional-Nacelle inspection(AD,AM,AE) 220-Static pitchlocks 220-Dynamic pitchlocks 110-Blade segment gear(Check dome hours) 110-Prop Balance 220-TD amp test 110-FGPL(if sync is removed for prop balance) |
|
Can you send an aircraft through the birdbath with ordnance?
|
Aircraft cannot go through the bird bath with ANY external stores loaded.
|
|
What will be different about the "A" sheet and Preflight/Turnaround when Ordnance is loaded?
|
They will have the ordnance listed on it, and they will have to be signed by a QASO.
|
|
Can you turn with ordnance loaded on an aircraft?
|
Yes but only low power turns. Never do high powers.
|
|
What does Irac #1 in the PMIC say concerning EDCs part # 206400-7-1a state?
|
It states the removal interval has been changed from 2,000hrs to 4,000hrs.
|
|
When an APU genterator has exceeded it's removal interval when must you remove the generator.
|
The generator may remain in place unti the APU is removed for other maintenance actions.
|