Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
583 Cards in this Set
- Front
- Back
- 3rd side (hint)
|
WHAT FORM IS OPNAV 4790/7B? |
PMS FEEDBACK REPORT |
|
|
|
WHAT FORM IS OPNAV 4709/12? |
QAR/CDI DESIGNATION |
|
|
|
WHAT FORM IS OPNAV 4709/29? |
AESR |
|
|
|
WHAT FORM IS OPNAV 4790/34? |
REQUIRED READING FORM |
|
|
|
WHAT FORM IS OPNAV 4790/51? |
SE CUSTODY RECORD |
|
|
|
WHAT FORM IS OPNAV 4790/52? |
SE CUSTODY RECORD |
|
|
|
WHAT FORM IS OPNAV 4790/60? |
VIDS MAF |
|
|
|
WHAT FORM IS OPNAV 4790/63? |
MOBILE FACILITY |
|
|
|
WHAT FORM IS OPNAV 4790/64? |
SE TRANS. REPORT (I&R) |
|
|
|
WHAT FORM IS OPNAV 4790/66? |
TPDR |
|
|
|
WHAT FORM IS OPNAV 4790/80? |
SE REWORK SCHEDULE REQUEST |
|
|
|
WHAT FORM IS OPNAV 4790/102? |
"YELLOW" LICENSE (SE CERTIFICATIONS CARD) |
|
|
|
WHAT FORM IS OPNAV 4790/108? |
SE MISUSE & ABUSE FORM |
|
|
|
WHAT FORM IS OPNAV 4790/136A? |
PRES/DEPRES FORM |
|
|
|
WHAT IS DD FORM 200? |
FINANCIAL LIABILITY INVESTIGATION OF PROPERTY LOSS |
|
|
|
WHAT FORM IS NA 4790/3? |
MRC |
|
|
|
WHAT FORM IS NA 13650/1? |
IMRL REVISION REQUEST |
|
|
|
WHAT FORM IS NAT02? |
SE TD LISTING |
|
|
|
WHAT FORM IS NAVSUP 306? |
CUSTODY RECORD FOR TOOLS |
|
|
|
WHAT FORM IS NAVPERS 1740/6? |
FAMILY CARE PLAN CERTIFICATE |
|
|
|
WHAT FORM IS NAVPERS 1740/7? |
FAMILY CARE PLAN ARRANGEMENT |
|
|
|
WHAT IS THE MHE FORM? |
"WHITE" LICENSE (MATERIALS HANDLER EQUIPMENT) [FORKLIFTS, TRUCKS, ETC.] |
|
|
|
WHAT FORM IS SF 368? |
PQDR FORM |
|
|
|
WHAT FORM CONSTITUTES YOUR GOVERNMENT LICENSE? |
FORM 346 |
|
|
|
WHAT IS THE COMMAND TECHNICAL MANUAL? |
NA 00-25-100 |
|
|
|
WHAT IS THE BASIC HANDLING & SAFETY MANUAL? |
NA 00-80T-96 |
|
|
|
WHAT IS HYDRAULIC MANUAL? |
NA 01-1A-17 |
|
|
|
WHAT IS THE HOSE & TUBE MANUAL? |
NA 01-1A-20 |
|
|
|
WHAT IS THE PARTICLE MANUAL (PN# 8011-3)? |
NA 17-15-521 |
|
|
|
WHAT IS THE SE CLEANING, PRES & CORROSION MANUAL? |
NA 17-1-125 |
|
|
|
WHAT IS THE HYDRAULIC FLUID KIT MANUAL (PN# 57L414)? |
NA 17-15E-52 |
|
|
|
WHAT MANUAL IS THE BUPERSINST 1430.16? |
ADVANCEMENT MANUAL FOR ENLISTED PERSONNEL |
|
|
|
WHAT MANUAL IS THE BUPERSINST 1610.10? |
NAVY EVALUATION SYSTEM |
|
|
|
WHAT MANUAL IS THE OPNAVINST 1740.5A? |
FINANCIAL MANAGEMENT EDUCATION TRAINING |
|
|
|
WHAT MANUAL IS THE OPNAVINST 5100.19? |
NAVOSH AFLOAT |
|
|
|
WHAT MANUAL IS THE OPNAVINST 5100.23? |
NAVOSH ASHORE |
|
|
|
WHAT MANUAL IS THE OPNAVINST 5100.25A? |
NAVY REC., ATHLETIC & HOME SAFETY |
|
|
|
WHAT MANUAL IS THE OPNAVINST 5350.4? |
DRUG & ALCOHOL ABUSE PREVENTION & CONTROL |
|
|
|
WHAT MANUAL IS THE OPNAVINST 5354.1? |
EQUAL OPPORTUNITY POLICY |
|
|
|
WHAT MANUAL IS THE OPNAVINST 5370.2? |
NAVY FRATERNIZATION POLICY |
|
|
|
WHAT MANUAL IS THE OPNAVINST 6110.1? |
PHYSICAL READINESS PROGRAM |
|
|
|
WHAT MANUAL IS THE SECNAVINST 5100.13? |
TOBACCO POLICY |
|
|
|
WHAT MANUAL IS THE SECNAVINST 5300.26? |
SEXUAL HARRASSMENT POLICY |
|
|
|
WHAT IS THE ACRONYM FOR THE PROGRAMS QA "MANAGES"? |
ASSCAN |
|
|
|
WHAT ARE THE PROGRAMS THAT QA "MANAGES"? |
A-AUDITS S-SAFETY S-SE MISUSE & ABUSE C-CTPL A-AVIATION CONFINED SPACE PROGRAM N-NAMDRP |
|
|
|
IN RELATION TO NAMDRP, WHAT DOES ISSC/LMTC STAND FOR? |
RESPONSE TIME FRAME |
|
|
|
IN RELATION TO NAMDRP, WHAT DOES MC/PC/MMC DO? |
PREPARE & HANDLE EI PQDR |
|
|
|
WHAT IS AN HMR FOR? |
MATERIAL DEFICIENCES |
|
|
|
WHAT IS THE ACRONYM FOR THE 6 SECTIONS OF THE OPNAV 4790/51? |
CRPTP + MISC. (PRONOUNCED CRIP-TOP) |
|
|
|
WHAT ARE THE SECTIONS OF THE OPNAV 4790/51 FORM? |
SECTION 1- CUSTODY & TRANSFER SECTION 2- RECORD OF REWORK SECTION 3- PRES/DEPRES SECTION 4- TD'S SECTION 5- PMS SECTION 6- MISC. |
|
|
|
WHAT IS BCM 1? |
REPAIR NOT AUTHORIZED |
|
|
|
WHAT IS BCM 2? |
LACK OF TOOLS/EQUIPMENT |
|
|
|
WHAT IS BCM 3? |
LACK OF SKILLS |
|
|
|
WHAT IS BCM 4? |
LACK OF PARTS |
|
|
|
WHAT IS BCM 5? |
FAILS CHECK & TEST |
|
|
|
WHAT IS BCM 6? |
LACK OF PUBS |
|
|
|
WHAT IS BCM 7? |
BEYOND CAPABLE REPAIR |
|
|
|
WHAT IS BCM 8? |
ADMINISTRATIVE |
|
|
|
WHAT IS BCM 9? |
CONDEMED |
|
|
|
WHAT IS THE MNEMONIC (LEARNING DEVICE) USED TO REMEMBER MDRS? |
DID MY JOB TODAY BUT STILL BELIEVE FLEET RESERVE FAT CHIEFS ARE WORTHLESS |
|
|
|
WHAT DOES MDR STAND FOR? |
MAINTENANCE DATA REPORTING |
|
|
|
WHAT IS MDR 1? |
DAILY |
|
|
|
WHAT IS MDR 2? |
MONTHLY |
|
|
|
WHAT IS MDR 3? |
JCN |
|
|
|
WHAT IS MDR 4-1? |
TD'S |
|
|
|
WHAT IS MDR 4-2? |
INTERMEDIATE TD'S |
|
|
|
WHAT IS MDR 5? |
BUNO |
|
|
|
WHAT IS MDR 6? |
SYSTEM |
|
|
|
WHAT IS MDR 7? |
BCM |
|
|
|
WHAT IS MDR 8? |
FAILED PARTS |
|
|
|
WHAT IS MDR 9? |
REPAIR CYCLE |
|
|
|
WHAT IS MDR 10? |
FOD |
|
|
|
WHAT IS MDR 11? |
CORROSION |
|
|
|
WHAT IS MDR 12? |
NO DEFECT |
|
|
|
WHAT IS MDR 13? |
WHEN DISCOVERED |
|
|
|
WHICH CODE OF CONDUCT ARTICLE STATES "I AM AN AMERICAN, FIGHTING IN THE FORCES WHICH GUARD MY COUNTRY AND OUR WAY OF LIFE. I AM PREPARED TO GIVE MY LIFE IN THEIR DEFENSE"? |
ARTICLE I |
|
|
|
WHICH CODE OF CONDUCT ARTICLE STATES "I WILL NEVER SURRENDER OF MY OWN FREE WILL. IF IN COMMAND I WILL NEVER SURRENDER THE MEMBERS OF MY COMMAND WHILE THEY STILL HAVE THE MEANS TO RESIST"? |
ARTICLE II |
|
|
|
WHICH CODE OF CONDUCT ARTICLE STATES "IF I AM CAPTURED I WILL CONTINUE TO RESIST BY ALL MEANS AVAILABLE. I WILL MAKE EVERY EFFORT TO ESCAPE AND AID OTHER TO ESCAPE. I WILL ACCEPT NEITHER PAROLE NOR SPECIAL FAVORS FROM THE ENEMY"? |
ARTICLE III |
|
|
|
WHICH CODE OF CONDUCT ARTICLE STATES "IF I BECOME A PRISONER OF WAR, I WILL KEEP FAITH WITH MY FELLOW PRISONERS. I WILL GIVE NO INFORMATION OR TAKE PART IN ANY ACTION WHICH MIGHT BE HARMFUL TO MY COMRADES. IF I AM SENIOR, I WILL TAKE COMMAND. IF NOT, I WILL OBEY THE LAWFUL ORDERS OF THOSE APPOINTED OVER ME AND WILL BACK THEM UP IN EVERY WAY"? |
ARTICLE IV |
|
|
|
WHICH CODE OF CONDUCT ARTICLE STATES "WHEN QUESTIONED, SHOULD I BECOME A PRISONER OF WAR, I AM REQUIRED TO GIVE NAME, RANK, SERVICE NUMBER, AND DATE OF BIRTH. I WILL EVADE AND ANSWERING FURTHER QUESTIONS TO THE UTMOST OF MY ABILITY. I WILL MAKE NO ORAL OR WRITTEN STATEMENTS DISLOYAL TO MY COUNTRY AND ITS ALLIES OR HARMFUL TO THEIR CAUSE"? |
ARTICLE V |
|
|
|
WHICH CODE OF CONDUCT ARTICLE STATES "I WILL NEVER FORGET THAT I AM AN AMERICAN, FIGHTING FOR FREEDOM, RESPONSIBLE FOR MY ACTIONS, AND DEDICATED TO THE PRINCIPLES WHICH MADE MY COUNTRY FREE. I WILL TRUST IN MY GOD AND IN THE UNITED STATES OF AMERICA"? |
ARTICLE VI |
|
|
|
WHAT IS THE PATH/SEQUENCE FOR THE AIR CONDITIONER? |
COMPRESSOR- IN (LPG), OUT (HPG) CONDENSER- IN (HPG), OUT (HPL) RECEIVER----> EXPANSION VALVE [TXV]- IN (HPL), OUT (LPL) EVAPORATOR- IN (LPL), OUT (LPG) BACK TO COMPRESSOR |
|
|
|
WHAT IS THE SYMBOL USED TO REPRESENT VOLTS? |
VOLTS = E |
|
|
|
WHAT IS THE SYMBOL USED TO REPRESENT AMPS? |
AMPS = I |
|
|
|
WHAT IS THE SYMBOL USED TO REPRESENT OHMS? |
OHMS = R |
|
|
|
WHAT IS THE ELECTRICAL FORMULA FOR FINDING VOLTS? |
E= I x R |
|
|
|
WHAT IS THE ELECTRICAL FORMULA FOR FINDING AMPS? |
I= E / R |
|
|
|
WHAT IS THE ELECTRICAL FORMULA FOR FINDING OHMS? |
R= E / I |
|
|
|
WHICH NEC IS FOR TRAINING? |
9502 |
|
|
|
WHICH NEC IS FOR CRYO? |
7601 |
|
|
|
WHICH NEC IS FOR SE AC & MMF TECHNICIAN? |
7603 |
|
|
|
WHICH NEC IS FOR TURBINE? |
7606 |
|
|
|
WHICH NEC IS FOR SHORE TOW TRACTOR? |
7607 |
|
|
|
WHICH NEC IS FOR SE MAINTENANCE MANAGER? |
7609 |
|
|
|
WHICH NEC IS FOR AFLOAT HYD? |
7612 |
|
|
|
WHICH NEC IS FOR SHORE HYD? |
7613 |
|
|
|
WHICH NEC IS FOR SHORE MEPPS? |
7614 |
|
|
|
WHICH NEC IS FOR AFLOAT MEPPS? |
7615 |
|
|
|
WHICH NEC IS FOR SHORE MAINTENANCE CRANE INTERMEDIATE TECHNICIAN? |
7616 |
|
|
|
WHICH NEC IS FOR CRASH EQUIPMENT TECHNICIAN (SEA)? |
7617 |
|
|
|
WHICH NEC IS FOR AFLOAT SE TECHNICIAN? |
7618 |
|
|
|
WHAT IS UCMJ 7? |
APPREHENSION |
|
|
|
WHAT IS UCMJ 15? |
NON-JUDICIAL PUNISHMENT [NJP] (LARCENY) |
|
|
|
WHAT IS UCMJ 80? |
ATTEMPS |
|
|
|
WHAT IS UCMJ 81? |
CONSPIRACY |
|
|
|
WHAT IS UCMJ 82? |
SOLICITATION |
|
|
|
WHAT IS UCMJ 85? |
DESERTION |
|
|
|
WHAT IS UCMJ 86? |
ABSENCE WIHTOUT LEAVE (UA) |
|
|
|
WHAT IS UCMJ 87? |
MISSING MOVEMENT |
|
|
|
WHAT IS UCMJ 92? |
FAILURE TO OBEY LAWFUL ORDERS |
|
|
|
WHAT IS UCMJ 93? |
MALTREATMENT |
|
|
|
WHAT IS UCMJ 94? |
MUTINY/SEDITION (REVOLT) |
|
|
|
WHAT IS UCMJ 104? |
AIDING THE ENEMY |
|
|
|
WHAT IS UCMJ 106? |
SPIES |
|
|
|
WHAT IS UCMJ 106A? |
ESPIONAGE |
|
|
|
WHAT IS UCMJ 107? |
FALSE STATEMENTS |
|
|
|
WHAT IS UCMJ 111? |
DRUKEN/WRECKLESS DRIVING |
|
|
|
WHAT IS UCMJ 112? |
DRUNK ON DUTY |
|
|
|
WHAT IS UCMJ 112A? |
WRONGFUL USE, POSSESSION OF CONTROLLED SUBSTANCES |
|
|
|
WHAT IS UCMJ 114? |
DUELING |
|
|
|
WHAT IS UCMJ 115? |
MALINGERING (TO PRETEND ILLNESS TO AVOID WORK) |
|
|
|
WHAT IS UCMJ 117? |
PROVOKING SPEECH OR GESTURES |
|
|
|
WHAT IS UCMJ 118? |
MURDER |
|
|
|
WHAT IS UCMJ 119? |
MANSLAUGHTER |
|
|
|
WHAT IS UCMJ 120? |
RAPE/CARNAL KNOWLEDGE |
|
|
|
WHAT IS UCMJ 122? |
ROBBERY |
|
|
|
WHAT IS UCMJ 123? |
FORGERY |
|
|
|
WHAT IS UCMJ 123A? |
MAKING, DRAWING, OR UTTERING CHECK -WITHOUT SUFFICIENT BALANCE |
|
|
|
WHAT IS UCMJ 124? |
MAIMING (TO IMPAIR, MAKE ESSENTIALLY DEFECTIVE) |
|
|
|
WHAT IS UCMJ 125? |
SODOMY (ANAL OR ORAL WITH OPPOSITE SEX) |
|
|
|
WHAT IS UCMJ 126? |
ARSON |
|
|
|
WHAT IS UCMJ 127? |
EXTORTION (ABUSE ON ONE'S OFFICE OR AUTHORITY TO OBTAIN MONEY) |
|
|
|
WHAT IS UCMJ 128? |
ASSAULT |
|
|
|
WHAT IS UCMJ 129? |
BURGLARY |
|
|
|
WHAT IS UCMJ 130? |
HOUSEBREAKING |
|
|
|
WHAT IS UCMJ 131? |
PERJURY (FALSE TESTIMONY UNDER OATH) |
|
|
|
WHAT IS UCMJ 132? |
FRAUD AGAINST U.S. |
|
|
|
WHAT IS UCMJ 134? |
GENERAL ARTICLE |
|
|
|
WHAT IS UCMJ 137? |
ARTICLES TO BE EXPLAINED |
|
|
|
WHAT IS THE AWM CODE M1? |
AWAITING DEPOT LEVEL REPAIR |
|
|
|
WHAT IS THE AWM CODE M2? |
LACK OF SE HANGAR SPACE |
|
|
|
WHAT IS THE AWM CODE M3? |
BACKLOG |
|
|
|
WHAT IS THE AWM CODE M4? |
OFF SHIFT HOURS |
|
|
|
WHAT IS THE AWM CODE M5? |
OTHER |
|
|
|
WHAT IS THE AWM CODE M6? |
AWAITING AIMD |
|
|
|
WHAT IS THE AWM CODE M7? |
FLIGHT/OPERATION BACKLOG |
|
|
|
WHAT IS THE AWM CODE M8? |
OTHER SHOP |
|
|
|
WHAT IS THE AWM CODE M9? |
FUNDING |
|
|
|
WHAT IS THE AWM CODE WS? |
WORK STOPPAGE |
|
|
|
WHAT IS THE AWM CODE WB? |
TRANSIT FROM AWP LOCKER |
|
|
|
WHAT IS THE AWM CODE WP? |
IN SHOP |
|
|
|
WHAT IS THE AWM CODE WQ? |
IN AWP LOCKER |
|
|
|
WHAT IS THE AWM CODE WT? |
IN TRANSIT AWP LOCKER |
|
|
|
WHAT IS THE AWM CODE CC? |
MAF CANCELLED |
|
|
|
WHAT IS THE AWM CODE CP? |
CONTRUCTOR PARTS |
|
|
|
WHAT IS THE AWM CODE CM? |
CONTRUCTOR MAINTENANCE |
|
|
|
WHAT IS THE AWM CODE A1? |
PRE-INDUCTION SCREENING |
|
|
|
WHAT WUC CODE IS USE FOR ACCEPTANCE, TRANSFER AND CONDITIONAL INSPECTIONS? |
030 |
|
|
|
WHAT WUC CODE IS USED FOR CORROSION PREVENTION? |
040 |
|
|
|
WHAT WUC CODE IS USED FOR PRESERVATION & DE-PRESERVATION? |
049 |
|
|
|
WHAT ORG CODE IS USED FOR ATLANTIC FLEET SHIP? |
C |
|
|
|
WHAT ORG CODE IS USED FOR PACIFIC FLEET SHIP? |
D |
|
|
|
WHAT ORG CODE IS USED FOR ATLANTIC FLEET SQUADRON/SHORE STATION? |
A |
|
|
|
WHAT ORG CODE IS USED FOR PACIFIC FLEET SQUADRON/SHORE STATION? |
P |
|
|
|
WHAT ORG CODE IS USED FOR MISCELLANEOUS ACTIVITIES? |
Z |
|
|
|
WHAT TD CODE IS USED TO REPRESENT SUPPORT EQUIPMENT CHANGE? |
62 |
|
|
|
WHAT TD CODE IS USED TO REPRESENT SUPPORT EQUIPMENT BULLETIN? |
63 |
|
|
|
WHAT ARE THE 4 "TYPES" OF TD'S? |
1. FORMAL CHANGE 2. INERIM CHANGE 3. BULLETIN 4. RAPID ACTION MINOR ENGINEERING CHANGES (RAMEC) |
|
|
|
WHAT ARE THE 4 "CATEGORIES" OF TD'S? |
1. IMMEDIATE 2. URGENT ACTION 3. ROUTINE ACTION 4. RECORD PURPOSE |
|
|
|
WHAT PROJECT CODE IS USED TO REPRESENT NEEDING MATERIAL TO REPAIR SE? |
BK0 |
|
|
|
WHAT PROJECT CODE IS USED TO REPRESENT STOPPING AWP UNDERGOING REPAIR? |
BK1 |
|
|
|
WHAT PROJECT CODE IS USED TO REPRESENT AN EXREP FOR NMC'S OR PMC'S? |
ZC8 |
|
|
|
WHAT PROJECT CODE IS USED TO REPRESENT BROAD ARROW? |
ZF7 |
|
|
|
HOW MANY DIFFERENT TYPES OF COURT MARTIAL ARE THERE? |
THREE |
|
|
|
WHAT DOES A SUMMARY COURT MARTIAL CONSISTS OF? |
ONE COMMISSIONED OFFICER |
|
|
|
WHAT DOES A SPECIAL COURT MARTIAL CONSISTS OF? |
NOT LESS THAN THREE MEMBERS |
|
|
|
WHAT DOES A GENERAL COURT MARTIAL CONSISTS OF? |
-NOT LESS THAN FIVE MEMBERS -BE REPRESENTED BY CIVILIAN COUNSEL AT ACCUSED EXPENSE |
|
|
|
WHAT ARE THE 3 SOURCES THAT CONTAIN THE BASIC DISCIPLINARY LAWS FOR THE U.S. NAVY? |
1. U.S. NAVY REGULATIONS 2. STANDARD ORGANIZATION AND REGULATIONS OF THE U.S. NAVY 3. UCMJ
|
|
|
|
ON WHAT DATE WAS THE UCMJ PLACED INTO EFFECT? |
31 MAY 1951 |
|
|
|
ON WHAT DATE WAS THE UCMJ PASSED BY CONGRESS? |
05 MAY 1950 |
|
|
|
WHO GETS A 21 GUN SALUTE? |
PRESIDENT |
|
|
|
WHO GETS A 19 GUN SALUTE? |
SECRETARY OF DEFENSE |
|
|
|
WHAT IS THE MINIMUM AMOUNT OF BATTLE STATIONS REQUIRED? |
2-MAIN/MEDICAL |
|
|
|
WHAT IS THE DISTANCE IN YARDS HONORS SHOULD BE RENDERED SHIP TO SHIP? |
600 YARDS |
|
|
|
WHAT IS THE DISTANCE IN YARDS HONORS SHOULD BE RENDERED BOAT TO BOAT? |
400 YARDS |
|
|
|
WHAT TRANS CODE IS 00? |
INVENTORY GAIN |
|
|
|
WHAT TRANS CODE IS 02? |
CHANGE IN REPORTING STATUS |
|
|
|
WHAT TRANS CODE IS 03? |
INVENTORY LOSS |
|
|
|
WHAT TRANS CODE IS 11? |
ON EQUIPMENT WORK |
|
|
|
WHAT TRANS CODE IS 12? |
ON EQUIPMENT WORK W/FAILED PARTS |
|
|
|
WHAT TRANS CODE IS 16? |
REMOVE RFI ITEM |
|
|
|
WHAT TRANS CODE IS 17? |
INSTALL RFI ITEM |
|
|
|
WHAT TRANS CODE IS 18? |
CANNIBALIZE-REFER TO HELP/NAMP |
|
|
|
WHAT TRANS CODE IS 19? |
CANNIBALIZE-REFER TO HELP NAMP |
|
|
|
WHAT TRANS CODE IS 21? |
REMOVE REPAIRABLE FOR TURN-IN |
|
|
|
WHAT TRANS CODE IS 23? |
REMOVE & REPLACE REPAIRABLE FROM END ITEM |
|
|
|
WHAT TRANS CODE IS 24? |
REMOVE ENGINE REPAIRABLE COMP |
|
|
|
WHAT TRANS CODE IS 25? |
REMOVE & REPLACE ENGINE COMPONENT |
|
|
|
WHAT TRANS CODE IS 30? |
WORK REQUEST |
|
|
|
WHAT TRANS CODE IS 31? |
OFF EQUIPMENT WORK |
|
|
|
WHAT TRANS CODE IS 32? |
OFF EQUIPMENT W/FAILED PARTS |
|
|
|
WHAT TRANS CODE IS 39? |
OFF EQUIPMENT CLOSEOUT |
|
|
|
WHAT TRANS CODE IS 41? |
TD |
|
|
|
WHAT TRANS CODE IS 47? |
TD ON SERIALIZED COMPONENTS |
|
|
|
WHAT DOES THE ACTION TAKEN CODE 0 MEAN? |
INSPECTION CONTROL, LOOK PHASE |
|
|
|
WHAT DOES THE ACTION TAKEN CODE "1" MEAN? |
REPAIR NOT AUTHORIZED |
|
|
|
WHAT DOES THE ACTION TAKEN CODE "2" MEAN? |
LACK OF EQUIPMENT, TOOLS, FACILITY |
|
|
|
WHAT DOES THE ACTION TAKEN CODE "3" MEAN? |
LACK OF TECHNICAL SKILLS |
|
|
|
WHAT DOES THE ACTION TAKEN CODE "4" MEAN? |
LACK OF PARTS |
|
|
|
WHAT DOES THE ACTION TAKEN CODE "5" MEAN? |
FAILS CHECK & TEST |
|
|
|
WHAT DOES THE ACTION TAKEN CODE "6" MEAN? |
LACK OF TECHNICAL DATA |
|
|
|
WHAT DOES THE ACTION TAKEN CODE "7" MEAN? |
BEYOND AUTHORIZED REPAIR DEPTH |
|
|
|
WHAT DOES THE ACTION TAKEN CODE "8" MEAN? |
ADMINISTRATIVE |
|
|
|
WHAT DOES THE ACTION TAKEN CODE "9" MEAN? |
CONDEMNED |
|
|
|
WHAT DOES THE ACTION TAKEN CODE "A" MEAN? |
NO REPAIR REQUIRED |
|
|
|
WHAT DOES THE ACTION TAKEN CODE "B" MEAN? |
REPAIR (NON-WUC ITEM) [REPLACEMENT OF ITEM; IE: SEALS, GASKET, TUBE OR HOSE] |
|
|
|
What is the maximum nitrogen output pressure of the A/U26U–4 nitrogen–servicing cart?
|
3,000 psi
|
|
|
|
The storage tank on the TMU–70 can hold a maximum of how many gallons of LOX?
|
50 gallons
|
|
|
|
What type of transfer system is incorporated on the TMU–70?
|
closed–loop
|
|
|
|
What parts are installed on a vehicle frame to provide additional strength at the point where the frame members are joined together?
|
Cross members
|
|
|
|
What is the preferred method of installing new members in a vehicle frame when replacement is required?
|
Oxyacetylene welding
|
|
|
|
The axle in a vehicle that transmits power from the transmission to the driving wheels is known as what type of axle?
|
A live axel
|
|
|
|
On a vehicle that uses coil springs in the suspension system, you can reduce pitching by taking which of the following actions?
|
By adding shock absorbers
|
|
|
|
What component(s) are added between the springs and the frame to eliminate squeaking?
|
Shock absorbers
|
|
|
|
Why are rubber mountings used for fastening shock absorbers to the frame and axle of a vehicle?
|
To provide controlled flexing of the springs
|
|
|
|
What is the major difference between the two types of power steering systems?
|
The manner in which the power steering pump is connected to the engine
|
|
|
|
In a steering system, what is the purpose of the tie rod?
|
To keep the front wheels in proper alignment
|
|
|
|
The ratio between the number of turns of the steering wheel and the number of degrees of movement of the pitman arm is the function of what component?
|
The sector gear only
|
|
|
|
Excessive play in a strong system is caused by which of the following conditions?
|
Low air pressure in the tires
|
|
|
|
Pivot inclination, caster, camber, toe–in and toe–out refer to which of the following terms?
|
Front–end geometry
|
|
|
|
Pivot inclination is a term referring to what position of the kingpin?
|
The number of degrees it is tilted from vertical towards the center of the vehicle
|
|
|
|
Positive caster is achieved when the knuckle pivots are tilted in what direction?
|
To the front of the vehicle
|
|
|
|
In a vehicle steering system, how is camber obtained?
|
By tilting the spindles slightly upward on the steering knuckle
|
|
|
|
You should check which of the following items to ensure proper operation when you servicing a vehicle with power steering?
|
The drive beltThe hoses and fittingsThe fluid level
|
|
|
|
To correct toe–in of a vehicle, you must adjust what component(s)?
|
The steering arm knuckle
|
|
|
|
If low weight is the major factor, which of the following materials should be used as a conductor?
|
Copper
|
|
|
|
What material is MOST widely used as a conductor in electrical equipment?
|
Copper
|
|
|
|
Resistance of a conductor will increase with which of the following changes to the cross–sectional area and length of the conductor?
|
Cross–sectional area is decreased, length is decreased
|
|
|
|
A material whose resistance decreases as the temperature increases has what temperature coefficient?
|
Negative
|
|
|
|
A material whose resistance remains constant as the temperature increases has what temperature coefficient?
|
Neutral
|
|
|
|
Resistance bears which, if any, of the following relationships to conductance?
|
A direct relationship
|
|
|
|
Which of the following electronic devices operates by virtue of the movement of electrons within a solid piece of semiconductor material?
|
TransistorJunction diodeSolid–state device
|
|
|
|
Which of the following electronic devices is a minute piece of semiconductor material that can produce complete electronic circuit functions?
|
Integrated circuit
|
|
|
|
Which of the following terms is used for the decrease in resistance as the temperature of the semiconductor increases?
|
Negative temperature coefficient
|
|
|
|
In addition to rectifying properties, selenium has the property of being light sensitive. How is selenium's resistance affected by light?
|
It increases with an increase in light intensity
|
|
|
|
One of the most sensitive elements of semiconductor materials is galena. Galena is a crystalline form of what material?
|
Bismuth
|
|
|
|
What significant discovery caused a breakthrough in the development of semiconductor devices?
|
The junction diode
|
|
|
|
Which of the following devices is frequently used to regulate power supply voltages at precise levels?
|
Zener diode
|
|
|
|
Which of the following solid–state devices has both gain and fast–switching capabilities?
|
Junction diode
|
|
|
|
One of the prime dangers to the semiconductor diode is heat. Excessive current generated by heat which eventually destroys a diode is called ________________.
|
thermal runaway
|
|
|
|
When replacing a diode in a circuit, which of the following safety precautions should you observe in removing the diode from the circuit?
|
Do not: Pry the diode from the circuit
|
|
|
|
As you make a front–to–back ratio check of a diode with an ohmmeter, your first measurement (forward) is a low resistance reading, and your second measurement (reverse) is also a low reading. What should be your evaluation of the diode?
|
It is good
|
|
|
|
What are normally the front–to–back ratio of (a) a power rectifier and (b) a signal diode?
|
(a) 300:1 (b) 10:1
|
|
|
|
What test is best when checking a diode?
|
A forward and reverse resistance check with an ohmmeter
|
|
|
|
What series of OPNAV instructions provides detailed instructions on a wide range of safety concerns?
|
5100
|
|
|
|
Which of the following types of capacitors are referred to as self–healing?
|
Oil
|
|
|
|
A substance that cannot be reduced to a simpler form by chemical means is called a/an __________.
|
element
|
|
|
|
For which of the following purposes is a cathode–ray oscilloscope used?
|
To visually analyze waveforms
|
|
|
|
What term applies to the difference between the speed of the rotating stator field and the rotor speed?
|
Slip
|
|
|
|
What term is used to indicate current gain in a common–collector configuration?
|
Gamma
|
|
|
|
The ability of a material to retain magnetism is called ____________.
|
reluctance
|
|
|
|
In a schematic diagram of a PN junction diode, which of the following symbols represents the cathode (N–type material)?
|
The vertical bar
|
|
|
|
Why is the Zener diode an ideal voltage regulator?
|
The voltage across the diode remains almost constant after breakdown
|
|
|
|
Restorative work performed on a item of support equipment is considered what type(s) of work?
|
Rework and upkeep maintenance
|
|
|
|
The left–hand rule for generators states that the thumb of the left hand points in the direction of motion of the ____________.
|
conductor
|
|
|
|
In a forward–biased PN junction, when an electron leaves the negative terminal of the battery and enters the N material, it becomes what type of carrier?
|
Majority
|
|
|
|
What type of bias makes a diode act as an open switch?
|
Reverse
|
|
|
|
At the intermediate level of maintenace, what copies of the VIDS/MAF are forwarded to the work center upon component induction for repair?
|
Copies 1, 4, and 5
|
|
|
|
An atom is the smallest possible particle that retains the characteristic of which of the following substances?
|
An element
|
|
|
|
Adjacent phase windings of a 3–phase motor stator are what total number of degrees apart?
|
120 degrees
|
|
|
|
Current in an electric circuit is caused by which of the following actions
|
*Electrons moving from negative to positive
|
|
|
|
How can the direction of rotation be changed in a dc motor?
|
By reversing either the armature connections or the field connections
|
|
|
|
What is the unit of measurement for inductance?
|
Henry
|
|
|
|
When the voltage applied to the armature of a DC shunt motor is decreased, what happens to the motor speed?
|
It decreases
|
|
|
|
What is/are the purpose(s) of the PN junction diode?
|
To rectify only
|
|
|
|
Voltage is induced in what part of an alternator?
|
The armature
|
|
|
|
What are the two junctions of a transistor?
|
Emitter–base and base–collector
|
|
|
|
What component cause(s) a generator to produce a DC voltage instead of an AC voltage at its output?
|
The commutator
|
|
|
|
The failure to start an engine is usually caused by which of the following systems?
|
Ignition
|
|
|
|
A vacuum gage reading indicates what?
|
The difference between atmospheric pressure and the pressure within the intake manifold
|
|
|
|
Breaker point spring tension that is too strong will affect high speed performance of an engine by causing point _________.
|
Bouncing
|
|
|
|
Which of the following items would be used to intensify the field force of an electromagnetic coil?
|
Iron core
|
|
|
|
Which of the following describes how the rotor coil is wound?
|
series
|
|
|
|
Where are the slip rings mounted in the alternator?
|
On the rotor shaft
|
|
|
|
The central junction in the eye stator is called whaat junction?
|
neutral
|
|
|
|
T or F. In AC generators the armature can be the rotor or stator.
|
True
|
|
|
|
In a DC generator, the load receives current from which of the following components?
|
brushes
|
|
|
|
What unit of the air conditioner removes and dissipates latent heat from the compressed gas?
|
condenser
|
|
|
|
What is the color of the drying agent in the chemical drier?
|
white
|
|
|
|
What is the color of the indicating agent in the chemical drier?
|
blue
|
|
|
|
Presence of moisture will change the color of the indicating agent to ________.
|
pink
|
|
|
|
What term implies that an expenditure has been authorized?
|
Appropiation
|
|
|
|
When are OPTAR funds provided by TYCOM?
|
FIscal Quarters
|
|
|
|
T or F. Etching is the initial process of eating away the surface of a metal.
|
True
|
|
|
|
Etching is generally evidenced by _____________.
|
dull appearance
|
|
|
|
The two types of surface corrosion are ___________ and ___________.
|
etching and pitting
|
|
|
|
Intergranular corrosion attacks the _________________________________
|
grain boundaries of an alloy.
|
|
|
|
T or F. Intergranular corrosion is difficult to detect because it attacks the surface of a metal and is camouflaged by a powdery deposit.
|
False
|
|
|
|
The corrosion that attacks between the lamination of metal is called ____________.
|
exfoliation
|
|
|
|
How may exfoliation corrosion be detected visually?
|
A blister–like raising or peeling on the surface of a metal
|
|
|
|
The corrosion that results when two different metals are joined in the presence of moisture is ______________.
|
galvanic
|
|
|
|
Stress corrosion is most likely to attack a metal structure at any point __________________________.
|
that is subject to flexing
|
|
|
|
What do the letters MFP indicate?
|
Moisture and fungus proofing
|
|
|
|
Type I oxygen is _________ form.Type II oxygen is _________ form.
|
gaseous, liquid
|
|
|
|
T or F. Cubic inches is the unit of measure when ordering gaseous oxygen.
|
False
|
|
|
|
T or F. Liquid oxygen will change to a gas when warmed to its boiling point which is –279F.
|
True
|
|
|
|
T or F. The expansion ratio of oxygen from liquid to a gas is 862 to 1.
|
True
|
|
|
|
The unit of measure for ordering liquid oxygen is the gallon.
|
True
|
|
|
|
Liquid nitrogen has a boiling of minus 320F.
|
True
|
|
|
|
Common types of micrometer are
|
inside, outside, and depth
|
|
|
|
Whats the purpose of a micrometer?
|
To make precision measurements in thousandths of a inch
|
|
|
|
T or F. The three types of micrometers are available in two models, which are the standard and the vernier model.
|
True
|
|
|
|
What is the recommended lubricant for oxygen fittings and equipment?
|
beeswax
|
|
|
|
Pivot inclination, caster, camber, toe–in, toe–out are terms referred to collectively as
|
wheel alignment
|
|
|
|
Steering knuckle tilt, forward or rearward, is called
|
caster
|
|
|
|
Positive caster is achieved when the knuckle pivots are tilted in what direction?
|
backward
|
|
|
|
The tilt of the wheels, either in or out at the top, is called
|
camber
|
|
|
|
To balance the effects, of camber, the wheels should be
|
toed–in
|
|
|
|
What two extinguishing agents are used on the P–25?
|
AFFF 375 gals. and Halon 400 lbs
|
|
|
|
What are the general subject classifications # assigned to SE
|
17 and 19
|
|
|
|
A routine message must be incorporated in a MIM within how many days?
|
5
|
|
|
|
CDI stamps may not be re–issued before a period of how many months?
|
3 months
|
|
|
|
What is the manual for the SE Basic Handling and Safety?
|
NAVAIR 00–80T–96
|
|
|
|
To insure proper thread grip at least how many threads shall protrude thru the nut?
|
2
|
|
|
|
What is the Tire Inflator Kit manual?
|
NA 17–1–123
|
|
|
|
What are three types of corrosion?
|
Light, moderate, and severe
|
|
|
|
T or F. The CTPL stamp that appears on the front of any manual must have the activity, copy#, and W/C.
|
True
|
|
|
|
QA Audits fall into the following categories.
|
Special and Work Center
|
|
|
|
Records of audits are kept for how long?
|
1 year
|
|
|
|
A CAT I TPDR must be submitted in what matter
|
Priority message within 24 hours
|
|
|
|
T or F. CAT II QDR's are submitted by Naval Message
|
False
|
|
|
|
CAT I QDR will be submitted by
|
Urgent Message within one working day
|
|
|
|
Class I water pumped nitrogen are marked how
|
2 black stripes
|
|
|
|
What pub would provide info on identification of SEC's required for SE equipment?
|
NA–00–500SE
|
|
|
|
What does the letters SM&R stand for?
|
Source, Maintenance, and Recoverability
|
|
|
|
The DOD single line item requisition system document form is what?
|
DD 1348
|
|
|
|
T or F. Crossover ducts direct the compressed air from the first–stage to the second stage impellers.
|
True
|
|
|
|
T or F. A turbocharger uses wasted exhaust energy to increase the amount of air taken into an engine.
|
True
|
|
|
|
T or F. Superchargers and turbochargers are lubricated internally.
|
True
|
|
|
|
To check the secondary ignition system you should hold the wire how far apart
|
1/4"T
|
|
|
|
T or F. The three categories of primers are sacrificial, barrier, and corrosion–inhibitor
|
True
|
|
|
|
The TMU/70 has a 50–gallon dewar tank and a ___ liter dewar transfer tank.
|
15 liter
|
|
|
|
The P–16 is powered by a what
|
2 cycle diesel engine
|
|
|
|
What are the two active ingredients in a lead–acid battery?
|
Lead and sulfuric acid
|
|
|
|
A micron is equivalent to
|
0.0000394
|
|
|
|
When bleeding brake systems where do you start first?
|
longest brake line
|
|
|
|
Anode is positive or negative
|
positive
|
|
|
|
Cathode is positive or negative
|
negative
|
|
|
|
What part of the NSN break down is the national item identification number (NIIN) 1560–00–123–4567
|
123–4567
|
|
|
|
A tachometer on a V8 engine is wired to the ________.
|
coil
|
|
|
|
What are the types of auto timing advance mechanisms?
|
centrifugal and vacuum device
|
|
|
|
The gear type oil pump is driven by the
|
camshaft gear
|
|
|
|
The crankshaft and camshaft stay timed by the use of what
|
belts and chains
|
|
|
|
What are the valve positions when a 4 stroke engine is on the power stroke?
|
Intake is closed, exhaust is closed
|
|
|
|
The battery ignition system consist of how many circuits
|
two
|
|
|
|
The principle parts of any steering gear unit consists of
|
sector and worm gear
|
|
|
|
How many complete revolutions must you have when taking a compression test?
|
4
|
|
|
|
The subject classification of publications in group 17 is
|
machinery, tools, and test equipment
|
|
|
|
The presence of stress corrosion in metal is indicated by _________.
|
cracks
|
|
|
|
A open in a rotor shows which of the following readings on a ohmmeter
|
infinite
|
|
|
|
When the selected mode on the A/M32C–17 Air Conditioner is in the ventilating mode what drives the blower?
|
belt
|
|
|
|
The process of heat treating a metal in order to change it's ductility is called
|
annealing
|
|
|
|
T or F. Double–action hand pumps are those in which a flow of fluid is created with every two strokes of the pump handle.
|
False
|
|
|
|
The bourdon tube pressure gage is operated by
|
fluid pressure
|
|
|
|
T or F. The manifold bypass valve is only used when recharging the system
|
True
|
|
|
|
What has happened when you notice that there is bubbles in the radiator?
|
cracked head or cylinder head gasket
|
|
|
|
Which of the following metals is used to construct spark plug electrodes?
|
Nickel
|
|
|
|
How many diodes rectify the alternating current?
|
6
|
|
|
|
What are the three categories of formal TD's?
|
urgent, routine, immediate
|
|
|
|
Tor F. The purpose of breaker points is to open the primary circuit, causing the magnetic field to collapse.
|
True
|
|
|
|
The TMU–70 storage tank should not be allowed to rise above what pressure.
|
55 PSI
|
|
|
|
A closed center fluid system is a
|
fluid system that remains pressurized from the pump to the directional control valve while the pump is operating
|
|
|
|
A open center fluid system has fluid but no
|
internal pressure when the actuating mechanisms are idle
|
|
|
|
Closed center systems are most widely used because
|
due to the fact that they require instantaneous operation to the directional control valve
|
|
|
|
Torque tie–bolts using a criss–cross pattern in
|
increments of 25% of the specified torque until torque is reached
|
|
|
|
Acceptance and shelf life of synthetic rubber hoses are as follows
|
acceptance life– 32 quartersshelf life– 20 quarters
|
|
|
|
A engine FOD incident report shall be submitted
|
within 5 working days after discovery
|
|
|
|
What gets entered in Section V of the 4790/51
|
NDI and proofload testing
|
|
|
|
TMU–70 Leading ParticularsWorking Pressure
|
Storage tank– __ PSI
|
Transfer tank– __ PSI
|
|
|
TMU–70 Leading ParticularsRelief Valve Settings
|
Storage tank vent line– __ psi
|
Fill line– __ psi
|
|
|
TMU–70 Leading ParticularsSafety Device Burst Pressure
|
Storage tank– __ psi
|
Transfer tank– ___ psi
|
|
|
TMU–70 storage tank is a
|
50 gal double walled Dewar
|
|
|
|
TMU–70 Transfer tank is a
|
15 liter double walled Dewar and is permanently attached to the storage tank
|
|
|
|
TMU–70 Storage pressure gage has a safe operating load pressure of 0–50 PSI indicated
|
by a green band and 50–100 PSI is indicated by a red band
|
|
|
|
TMU–70 storage tank liquid level gage has a safe operating level of up to 50 gallons indicated by a green band and unsafe operating level of more than 50 gallons
|
indicated by a red band
|
|
|
|
What is the function of the expansion valve?
|
To change the high pressure liquid into a low pressure as it enters the evaporator.
|
|
|
|
What is wheel camber?
|
Number of degrees that the wheels are tilted in or out at the top
|
|
|
|
What is the MDR for FOD?
|
MDR 10
|
|
|
|
What is the MDR for corrosion?
|
MDR 11
|
|
|
|
What is the MDR for No Defect?
|
MDR 12
|
|
|
|
When energy is transferred between a solid surface and a moving gas or liquid the process is called?
|
convection
|
|
|
|
When blasting aluminum alloys do not allow the blast stream to dwell on the same spot longer than
|
15 seconds
|
|
|
|
What is the distance the nozzle should be from the metal surface
|
46 inches in the glove box12 inches in the walk–in booth
|
|
|
|
MDR's1=Daily, 2=monthly , 3=JCN, 4= TD's, 5= Bureau/SN#, 6= system and component, 7= BCM, 8= failed parts, 9= repair cycle data, 10= FOD, 11= Corrosion, 12= A–799 No defect, 13= When Discovered
|
acronym cheat Did My Job Today But Still Believe Fleet Reserve Fat Chiefs Are Worthless
|
|
|
|
Refrigeration system Out of compressor ___________ to condenser From Condenser ___________ to expansion valve From expansion valve ________ to evaporator From evaporator ________ to compressor
|
1. HP gas2. HP liquid3. LP liquid 4. LP gas
|
|
|
|
What is the maximum nitrogen output pressure of the A/U26U–4 nitrogen–servicing cart?
|
3,000 psi
|
|
|
|
The storage tank on the TMU–70 can hold a maximum of how many gallons of LOX?
|
50 gallons
|
|
|
|
What type of transfer system is incorporated on the TMU–70?
|
closed–loop
|
|
|
|
What parts are installed on a vehicle frame to provide additional strength at the point where the frame members are joined together?
|
Cross members
|
|
|
|
What is the preferred method of installing new members in a vehicle frame when replacement is required?
|
Oxyacetylene welding
|
|
|
|
The axle in a vehicle that transmits power from the transmission to the driving wheels is known as what type of axle?
|
A live axel
|
|
|
|
On a vehicle that uses coil springs in the suspension system, you can reduce pitching by taking which of the following actions?
|
By adding shock absorbers
|
|
|
|
What component(s) are added between the springs and the frame to eliminate squeaking?
|
Shock absorbers
|
|
|
|
Why are rubber mountings used for fastening shock absorbers to the frame and axle of a vehicle?
|
To provide controlled flexing of the springs
|
|
|
|
What is the major difference between the two types of power steering systems?
|
The manner in which the power steering pump is connected to the engine
|
|
|
|
In a steering system, what is the purpose of the tie rod?
|
To keep the front wheels in proper alignment
|
|
|
|
The ratio between the number of turns of the steering wheel and the number of degrees of movement of the pitman arm is the function of what component?
|
The sector gear only
|
|
|
|
Excessive play in a strong system is caused by which of the following conditions?
|
Low air pressure in the tires
|
|
|
|
Pivot inclination, caster, camber, toe–in and toe–out refer to which of the following terms?
|
Front–end geometry
|
|
|
|
Pivot inclination is a term referring to what position of the kingpin?
|
The number of degrees it is tilted from vertical towards the center of the vehicle
|
|
|
|
Positive caster is achieved when the knuckle pivots are tilted in what direction?
|
To the front of the vehicle
|
|
|
|
In a vehicle steering system, how is camber obtained?
|
By tilting the spindles slightly upward on the steering knuckle
|
|
|
|
You should check which of the following items to ensure proper operation when you servicing a vehicle with power steering?
|
The drive beltThe hoses and fittingsThe fluid level
|
|
|
|
To correct toe–in of a vehicle, you must adjust what component(s)?
|
The steering arm knuckle
|
|
|
|
If low weight is the major factor, which of the following materials should be used as a conductor?
|
Copper
|
|
|
|
What material is MOST widely used as a conductor in electrical equipment?
|
Copper
|
|
|
|
Resistance of a conductor will increase with which of the following changes to the cross–sectional area and length of the conductor?
|
Cross–sectional area is decreased, length is decreased
|
|
|
|
A material whose resistance decreases as the temperature increases has what temperature coefficient?
|
Negative
|
|
|
|
A material whose resistance remains constant as the temperature increases has what temperature coefficient?
|
Neutral
|
|
|
|
Resistance bears which, if any, of the following relationships to conductance?
|
A direct relationship
|
|
|
|
Which of the following electronic devices operates by virtue of the movement of electrons within a solid piece of semiconductor material?
|
TransistorJunction diodeSolid–state device
|
|
|
|
Which of the following electronic devices is a minute piece of semiconductor material that can produce complete electronic circuit functions?
|
Integrated circuit
|
|
|
|
Which of the following terms is used for the decrease in resistance as the temperature of the semiconductor increases?
|
Negative temperature coefficient
|
|
|
|
In addition to rectifying properties, selenium has the property of being light sensitive. How is selenium's resistance affected by light?
|
It increases with an increase in light intensity
|
|
|
|
One of the most sensitive elements of semiconductor materials is galena. Galena is a crystalline form of what material?
|
Bismuth
|
|
|
|
What significant discovery caused a breakthrough in the development of semiconductor devices?
|
The junction diode
|
|
|
|
Which of the following devices is frequently used to regulate power supply voltages at precise levels?
|
Zener diode
|
|
|
|
Which of the following solid–state devices has both gain and fast–switching capabilities?
|
Junction diode
|
|
|
|
One of the prime dangers to the semiconductor diode is heat. Excessive current generated by heat which eventually destroys a diode is called ________________.
|
thermal runaway
|
|
|
|
When replacing a diode in a circuit, which of the following safety precautions should you observe in removing the diode from the circuit?
|
Do not: Pry the diode from the circuit
|
|
|
|
As you make a front–to–back ratio check of a diode with an ohmmeter, your first measurement (forward) is a low resistance reading, and your second measurement (reverse) is also a low reading. What should be your evaluation of the diode?
|
It is good
|
|
|
|
What are normally the front–to–back ratio of (a) a power rectifier and (b) a signal diode?
|
(a) 300:1 (b) 10:1
|
|
|
|
What test is best when checking a diode?
|
A forward and reverse resistance check with an ohmmeter
|
|
|
|
What series of OPNAV instructions provides detailed instructions on a wide range of safety concerns?
|
5100
|
|
|
|
Which of the following types of capacitors are referred to as self–healing?
|
Oil
|
|
|
|
A substance that cannot be reduced to a simpler form by chemical means is called a/an __________.
|
element
|
|
|
|
For which of the following purposes is a cathode–ray oscilloscope used?
|
To visually analyze waveforms
|
|
|
|
What term applies to the difference between the speed of the rotating stator field and the rotor speed?
|
Slip
|
|
|
|
What term is used to indicate current gain in a common–collector configuration?
|
Gamma
|
|
|
|
The ability of a material to retain magnetism is called ____________.
|
reluctance
|
|
|
|
In a schematic diagram of a PN junction diode, which of the following symbols represents the cathode (N–type material)?
|
The vertical bar
|
|
|
|
Why is the Zener diode an ideal voltage regulator?
|
The voltage across the diode remains almost constant after breakdown
|
|
|
|
Restorative work performed on a item of support equipment is considered what type(s) of work?
|
Rework and upkeep maintenance
|
|
|
|
The left–hand rule for generators states that the thumb of the left hand points in the direction of motion of the ____________.
|
conductor
|
|
|
|
In a forward–biased PN junction, when an electron leaves the negative terminal of the battery and enters the N material, it becomes what type of carrier?
|
Majority
|
|
|
|
What type of bias makes a diode act as an open switch?
|
Reverse
|
|
|
|
At the intermediate level of maintenace, what copies of the VIDS/MAF are forwarded to the work center upon component induction for repair?
|
Copies 1, 4, and 5
|
|
|
|
An atom is the smallest possible particle that retains the characteristic of which of the following substances?
|
An element
|
|
|
|
Adjacent phase windings of a 3–phase motor stator are what total number of degrees apart?
|
120 degrees
|
|
|
|
Current in an electric circuit is caused by which of the following actions
|
*Electrons moving from negative to positive
|
|
|
|
How can the direction of rotation be changed in a dc motor?
|
By reversing either the armature connections or the field connections
|
|
|
|
What is the unit of measurement for inductance?
|
Henry
|
|
|
|
When the voltage applied to the armature of a DC shunt motor is decreased, what happens to the motor speed?
|
It decreases
|
|
|
|
What is/are the purpose(s) of the PN junction diode?
|
To rectify only
|
|
|
|
Voltage is induced in what part of an alternator?
|
The armature
|
|
|
|
What are the two junctions of a transistor?
|
Emitter–base and base–collector
|
|
|
|
What component cause(s) a generator to produce a DC voltage instead of an AC voltage at its output?
|
The commutator
|
|
|
|
The failure to start an engine is usually caused by which of the following systems?
|
Ignition
|
|
|
|
A vacuum gage reading indicates what?
|
The difference between atmospheric pressure and the pressure within the intake manifold
|
|
|
|
Breaker point spring tension that is too strong will affect high speed performance of an engine by causing point _________.
|
Bouncing
|
|
|
|
Which of the following items would be used to intensify the field force of an electromagnetic coil?
|
Iron core
|
|
|
|
Which of the following describes how the rotor coil is wound?
|
series
|
|
|
|
Where are the slip rings mounted in the alternator?
|
On the rotor shaft
|
|
|
|
The central junction in the eye stator is called whaat junction?
|
neutral
|
|
|
|
T or F. In AC generators the armature can be the rotor or stator.
|
True
|
|
|
|
In a DC generator, the load receives current from which of the following components?
|
brushes
|
|
|
|
What unit of the air conditioner removes and dissipates latent heat from the compressed gas?
|
condenser
|
|
|
|
What is the color of the drying agent in the chemical drier?
|
white
|
|
|
|
What is the color of the indicating agent in the chemical drier?
|
blue
|
|
|
|
Presence of moisture will change the color of the indicating agent to ________.
|
pink
|
|
|
|
What term implies that an expenditure has been authorized?
|
Appropiation
|
|
|
|
When are OPTAR funds provided by TYCOM?
|
FIscal Quarters
|
|
|
|
T or F. Etching is the initial process of eating away the surface of a metal.
|
True
|
|
|
|
Etching is generally evidenced by _____________.
|
dull appearance
|
|
|
|
The two types of surface corrosion are ___________ and ___________.
|
etching and pitting
|
|
|
|
Intergranular corrosion attacks the _________________________________
|
grain boundaries of an alloy.
|
|
|
|
T or F. Intergranular corrosion is difficult to detect because it attacks the surface of a metal and is camouflaged by a powdery deposit.
|
False
|
|
|
|
The corrosion that attacks between the lamination of metal is called ____________.
|
exfoliation
|
|
|
|
How may exfoliation corrosion be detected visually?
|
A blister–like raising or peeling on the surface of a metal
|
|
|
|
The corrosion that results when two different metals are joined in the presence of moisture is ______________.
|
galvanic
|
|
|
|
Stress corrosion is most likely to attack a metal structure at any point __________________________.
|
that is subject to flexing
|
|
|
|
What do the letters MFP indicate?
|
Moisture and fungus proofing
|
|
|
|
Type I oxygen is _________ form.Type II oxygen is _________ form.
|
gaseous, liquid
|
|
|
|
T or F. Cubic inches is the unit of measure when ordering gaseous oxygen.
|
False
|
|
|
|
T or F. Liquid oxygen will change to a gas when warmed to its boiling point which is –279F.
|
True
|
|
|
|
T or F. The expansion ratio of oxygen from liquid to a gas is 862 to 1.
|
True
|
|
|
|
The unit of measure for ordering liquid oxygen is the gallon.
|
True
|
|
|
|
Liquid nitrogen has a boiling of minus 320F.
|
True
|
|
|
|
Common types of micrometer are
|
inside, outside, and depth
|
|
|
|
Whats the purpose of a micrometer?
|
To make precision measurements in thousandths of a inch
|
|
|
|
T or F. The three types of micrometers are available in two models, which are the standard and the vernier model.
|
True
|
|
|
|
What is the recommended lubricant for oxygen fittings and equipment?
|
beeswax
|
|
|
|
Pivot inclination, caster, camber, toe–in, toe–out are terms referred to collectively as
|
wheel alignment
|
|
|
|
Steering knuckle tilt, forward or rearward, is called
|
caster
|
|
|
|
Positive caster is achieved when the knuckle pivots are tilted in what direction?
|
backward
|
|
|
|
The tilt of the wheels, either in or out at the top, is called
|
camber
|
|
|
|
To balance the effects, of camber, the wheels should be
|
toed–in
|
|
|
|
What two extinguishing agents are used on the P–16?
|
AFFF 375 gals. and Halon 400 lbs
|
|
|
|
What are the general subject classifications # assigned to SE
|
17 and 19
|
|
|
|
A routine message must be incorporated in a MIM within how many days?
|
5
|
|
|
|
CDI stamps may not be re–issued before a period of how many months?
|
3 months
|
|
|
|
What is the manual for the SE Basic Handling and Safety?
|
NAVAIR 00–80T–96
|
|
|
|
To insure proper thread grip at least how many threads shall protrude thru the nut?
|
2
|
|
|
|
What is the Tire Inflator Kit manual?
|
NA 17–1–123
|
|
|
|
What are three types of corrosion?
|
Light, moderate, and severe
|
|
|
|
T or F. The CTPL stamp that appears on the front of any manual must have the activity, copy#, and W/C.
|
True
|
|
|
|
QA Audits fall into the following categories.
|
Special and Work Center
|
|
|
|
Records of audits are kept for how long?
|
1 year
|
|
|
|
A CAT I TPDR must be submitted in what matter
|
Priority message within 24 hours
|
|
|
|
T or F. CAT II QDR's are submitted by Naval Message
|
False
|
|
|
|
CAT I QDR will be submitted by
|
Urgent Message within one working day
|
|
|
|
Class I water pumped nitrogen are marked how
|
2 black stripes
|
|
|
|
What pub would provide info on identification of SEC's required for SE equipment?
|
NA–00–500SE
|
|
|
|
What does the letters SM&R stand for?
|
Source, Maintenance, and Recoverability
|
|
|
|
The DOD single line item requisition system document form is what?
|
DD 1348
|
|
|
|
T or F. Crossover ducts direct the compressed air from the first–stage to the second stage impellers.
|
True
|
|
|
|
T or F. A turbocharger uses wasted exhaust energy to increase the amount of air taken into an engine.
|
True
|
|
|
|
T or F. Superchargers and turbochargers are lubricated internally.
|
True
|
|
|
|
To check the secondary ignition system you should hold the wire how far apart
|
1/4"T
|
|
|
|
T or F. The three categories of primers are sacrificial, barrier, and corrosion–inhibitor
|
True
|
|
|
|
The TMU/70 has a 50–gallon dewar tank and a ___ liter dewar transfer tank.
|
15 liter
|
|
|
|
The P–16 is powered by a what
|
2 cycle diesel engine
|
|
|
|
What are the two active ingredients in a lead–acid battery?
|
Lead and sulfuric acid
|
|
|
|
A micron is equivalent to
|
0.0000394
|
|
|
|
When bleeding brake systems where do you start first?
|
longest brake line
|
|
|
|
Anode is positive or negative
|
positive
|
|
|
|
Cathode is positive or negative
|
negative
|
|
|
|
What part of the NSN break down is the national item identification number (NIIN) 1560–00–123–4567
|
123–4567
|
|
|
|
A tachometer on a V8 engine is wired to the ________.
|
coil
|
|
|
|
What are the types of auto timing advance mechanisms?
|
centrifugal and vacuum device
|
|
|
|
The gear type oil pump is driven by the
|
camshaft gear
|
|
|
|
The crankshaft and camshaft stay timed by the use of what
|
belts and chains
|
|
|
|
What are the valve positions when a 4 stroke engine is on the power stroke?
|
Intake is closed, exhaust is closed
|
|
|
|
The battery ignition system consist of how many circuits
|
two
|
|
|
|
The principle parts of any steering gear unit consists of
|
sector and worm gear
|
|
|
|
How many complete revolutions must you have when taking a compression test?
|
4
|
|
|
|
The subject classification of publications in group 17 is
|
machinery, tools, and test equipment
|
|
|
|
The presence of stress corrosion in metal is indicated by _________.
|
cracks
|
|
|
|
A open in a rotor shows which of the following readings on a ohmmeter
|
infinite
|
|
|
|
When the selected mode on the A/M32C–17 Air Conditioner is in the ventilating mode what drives the blower?
|
belt
|
|
|
|
The process of heat treating a metal in order to change it's ductility is called
|
annealing
|
|
|
|
T or F. Double–action hand pumps are those in which a flow of fluid is created with every two strokes of the pump handle.
|
False
|
|
|
|
The bourdon tube pressure gage is operated by
|
fluid pressure
|
|
|
|
T or F. The manifold bypass valve is only used when recharging the system
|
True
|
|
|
|
What has happened when you notice that there is bubbles in the radiator?
|
cracked head or cylinder head gasket
|
|
|
|
Which of the following metals is used to construct spark plug electrodes?
|
Nickel
|
|
|
|
How many diodes rectify the alternating current?
|
6
|
|
|
|
What are the three categories of formal TD's?
|
urgent, routine, immediate
|
|
|
|
Tor F. The purpose of breaker points is to open the primary circuit, causing the magnetic field to collapse.
|
True
|
|
|
|
The TMU–70 storage tank should not be allowed to rise above what pressure.
|
55 PSI
|
|
|
|
A closed center fluid system is a
|
fluid system that remains pressurized from the pump to the directional control valve while the pump is operating
|
|
|
|
A open center fluid system has fluid but no
|
internal pressure when the actuating mechanisms are idle
|
|
|
|
Closed center systems are most widely used because
|
due to the fact that they require instantaneous operation to the directional control valve
|
|
|
|
Torque tie–bolts using a criss–cross pattern in
|
increments of 25% of the specified torque until torque is reached
|
|
|
|
Acceptance and shelf life of synthetic rubber hoses are as follows
|
acceptance life– 32 quartersshelf life– 20 quarters
|
|
|
|
A engine FOD incident report shall be submitted
|
within 5 working days after discovery
|
|
|
|
What gets entered in Section V of the 4790/51
|
NDI and proofload testing
|
|
|
|
TMU–70 Leading ParticularsWorking Pressure
|
Storage tank– __ PSI
|
Transfer tank– __ PSI
|
|
|
TMU–70 Leading ParticularsRelief Valve Settings
|
Storage tank vent line– __ psi
|
Fill line– __ psi
|
|
|
TMU–70 Leading ParticularsSafety Device Burst Pressure
|
Storage tank– __ psi
|
Transfer tank– ___ psi
|
|
|
TMU–70 storage tank is a
|
50 gal double walled Dewar
|
|
|
|
TMU–70 Transfer tank is a
|
15 liter double walled Dewar and is permanently attached to the storage tank
|
|
|
|
TMU–70 Storage pressure gage has a safe operating load pressure of 0–50 PSI indicated
|
by a green band and 50–100 PSI is indicated by a red band
|
|
|
|
TMU–70 storage tank liquid level gage has a safe operating level of up to 50 gallons indicated by a green band and unsafe operating level of more than 50 gallons
|
indicated by a red band
|
|
|
|
What is the function of the expansion valve?
|
To change the high pressure liquid into a low pressure as it enters the evaporator.
|
|
|
|
What is wheel camber?
|
Number of degrees that the wheels are tilted in or out at the top
|
|
|
|
What is the MDR for FOD?
|
MDR 10
|
|
|
|
What is the MDR for corrosion?
|
MDR 11
|
|
|
|
What is the MDR for No Defect?
|
MDR 12
|
|
|
|
When energy is transferred between a solid surface and a moving gas or liquid the process is called?
|
convection
|
|
|
|
When blasting aluminum alloys do not allow the blast stream to dwell on the same spot longer than
|
15 seconds
|
|
|
|
What is the distance the nozzle should be from the metal surface
|
46 inches in the glove box12 inches in the walk–in booth
|
|
|
|
MDR's1=Daily, 2=monthly , 3=JCN, 4= TD's, 5= Bureau/SN#, 6= system and component, 7= BCM, 8= failed parts, 9= repair cycle data, 10= FOD, 11= Corrosion, 12= A–799 No defect, 13= When Discovered
|
acronym cheatDid My Job Today But Still Believe Fleet Reserve Fat Chiefs Are Worthless
|
|
|
|
Refrigeration system Out of compressor ___________ to condenser From Condenser ___________ to expansion valve From expansion valve ________ to evaporator From evaporator ________ to compressor
|
1. HP gas2. HP liquid3. LP liquid 4. LP gas
|
|
|
|
What is the purpose of the NC–10C MEPP?
|
It is designed for shore station use and supplies power for servicing, starting, and maintaining helicopters and jet aircraft
|
|
|
|
What protects the NC–10C MEPP's electrical system from overload?
|
By output circuit contactors, circuit breakers, over voltage and undervoltage relays, over frequency and under frequency relays, thermal overload relays, and fuses
|
|
|
|
What supplies NC–10C with dc power?
|
A six–phase, full–wave transformer–rectifier, by using three–phase, 400–Hz, 115/200–volt generator output as a power source
|
|
|
|
What are the four functional groups of instruments that the control panel of the NC–10C contains?
|
The electrical receptacles and adjustable resistors, the ac controls, the dc controls, and the engine controls
|
|
|
|
What is the ac output of the NC–10C MEPP?
|
90 kVA at 0.8 PF, 115/200 volt, three–phase, four–wire, 400–Hz
|
|
|
|
What component of the NC–10C MEPP supplies total power to the ac generator field circuit and regulates the output voltage within 1 percent no load to full load?
|
The ac voltage regulator
|
|
|
|
NC–10C engine shutdown faults are
|
High coolant temp; low lube oil pressure(10psi); overspeed 2150 +/– 50; and low fuel
|
|
|
|
NC–10C faults that bring engine to idle are
|
Over/under AC output voltage; over/under AC output frequency; DC output over voltage
|
|
|
|
The AN/USM–128 is used to monitor what
|
DC, three phase AC output voltages, and frequency
|
8 |
