Sodium chloride

Laboratory Manual is a chart on suggested liquids and the inference if the compound is soluble [1]. When then checked the pH of the solution by using pH strip. The solution had a pH>7. Then we did an anion test and discovered the compound reacted with chloride by producing a white precipitate. The precipitate that formed was an insoluble solid because Cl of NaCl reacted with Ag of AgNO3, creating a Cl- ion above the aqueous solution [3], results on Table 2. Finally we used a cation flame…

and barium chloride. If a sulfate anion was present in the unknown solution, then the anion would combine with the barium and form the precipitate, BaSO4, and the chlorine ion would combine with the unknown’s cation. In this case a sulfate anion was present in the unknown so the sulfate combined with barium in the form of a precipitate, and the potassium combined with the chloride ion as an aqueous solution. The same fundamentals are used when testing for a chloride anion. If a chloride anion…

This lab used techniques in steam distillation to extract crude oil from cloves. The cloves were boiled in a round bottom flask and using a hydrodistillation apparatus, the crude oil was separated from the cloves and sent into a clean flask. This step was used to separate the essential oils from the cloves (Setzer, W., 2008). The distillate was poured into a separatory funnel and extracted three times with dichloromethane to extract the water. After being extracted three times, a fifth of the…

In our experiment we evaluated which liquid yeast would produce gas the fastest by measuring how long it took for certain liquids to inflate a balloon. We hypothesized that if the yeast and sugar were placed in a warm,sugary environment like apple juice, then the yeast will produce more CO2 and cause the balloon to inflate faster. The control was the room temperature Throughout the experiment the type of balloons, size of the erlenmeyer flasks, amount of yeast, volume of each liquid, and the…

Red Dye 1 Red dye 1 is most likely a polar covalent molecule since we have found that it dissolves into water but does not break apart into ions. Just because it dissolves in water does not make it solely polar covalent, but since it has a relatively low conductivity, 534 mS/cm in the 0-20000 range, then it most likely is polar covalent. This is further confirmed with the fact that it does not react with NaOH, NaCl, or AgNO3, all ionic substances. The red dye does not react with NaOH since…

Amnion Tissue In this project, I also with amnion tissue collection, ChIP preparation and Real-time PCR technique. The aim of this work was to determine the gene activating H3K4me3 and gene repressing H3K27me3 levels and their ratios at the promoter regions of NAMPT inflammatory gene. Collection of Tissue Fetal membranes were collected from women undergoing elective cesarean section at absence of labour [not in labour (NIL), n = 5], during active labour [in labour (IL), n = 4] and preterm (n=5)…

nitrate and 1.0 mL of nitric acid were used for the ion test. Ammonium chloride and calcium chloride were the two compounds that were tested on to see if either were the unknown compound. After obtaining a balanced chemical equation that would allow for the synthesis of calcium chloride, it was determined that 0.858 g of magnesium chloride and 0.902 g of calcium carbonate needed to be used in order for 1.000 g of calcium chloride to…

DISCUSSION 6.1 FTIR SPECTROSCOPY It was observed from the FTIR graph that there was no shifting of peaks of metronidazole i,e., characteristic peak of the amine group (N-H streching) present in imidazole nucleus at 1030 cm-1 and presence of NH2 group at 3298 cm-1 in formulation. Hence, there was no interaction between drug and polymer. 6.2 METRONIDAZOLE MICROSPHERES 6.2.1 Optimization of speed (rpm) for preparation of microspheres Metronidazole microspheres were prepared using emulsion…

I. Abstract The experiment was about using a method of recrystallization to reform benzoic acid and unknown compound, and identifying that compound. The main principle is the polarity and solubility of compound. The compound was dissolved completely with distilled water in hot temperature and reformed back in cold environment. After the experiment, there were up to more than 50% of the compound being recrystallized and the unknown compound had the melting point at 165.2oC. The experiment…

Likewise, if the DCM was to be extracted with HCl, the sodium acetylsalicylate will not form and therefore the DCM layer will have contents of sodium acetylsalicylate which means that the inclusive percentage of Aspirin and the overall percentage of the unknown substance would be moderately superior. Sodium bicarbonate will remain in an alkaline state which means the acidic properties will be also be removed and therefore the extraction of sodium bicarbonate will be fairly weak during the…