Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
45 Cards in this Set
- Front
- Back
What is the reference designator of the BITE module? |
1A1A11 |
|
What is the frequency range of the AN/WSC-3? |
225.000 MHz to 399.975 MHz |
|
What is the transmit power output in AM? |
30 Watts |
|
What ratio of VSWR is the transmitter protected from? |
4:1 Ratio (found in Chapter 1 in the Tech Pub) |
|
What is the operating temperature of the AN/WSC-3? |
0-50 Celsius |
|
30 Watts is equal to how many dbw (decibel watts)? |
14.8 dbw |
|
What is the function of the TEST KEY switch when in the ON position? |
Continuously keys the transmitter |
|
What is the function of the CARRIER ON indicator? |
Indicates that the AN/WSC-3 transmit carrier is present |
|
What is the reference designator of the Receiver Front End? |
1A1A18 |
|
What mode of operation is modulated in the 1A1A8 Synthesizer? |
FM |
|
What three voltages do external shutdown NOT shut off? (Which voltages are present in standby?) |
+225,+68,+28 |
|
The L.O. frequency from the 1A1A8 is _______MHz offset from the window frequency. |
70 |
|
What is the model number of the handset unit? |
H-169/U (Not found in Tech Pub) |
|
What does meter 1A1M1 indicate? |
Total Operating Time |
|
How many amperes is fuse 1A1F1? |
15 Amps |
|
What does 1A1DS5 indicate? |
Malfunction |
|
How many preset channels can be programmed into the AN/WSC-3? |
20 |
|
The BITE Summing Circuit in the 1A1A2 outputs which BITE? |
BITE 1 |
|
1A1A2 A2J10 measures which voltages? |
+19.5 VDC |
|
When measuring 1A1W27J9 INT STD, what will be seen? |
5 MHz |
|
A logic level low at 1A1A25 P1-17 will select what? |
Secure |
|
What is the output of 1A1A6 P5? |
70 MHz |
|
Is the AM RF Carrier already modulated when it passes through the 1A1A6? |
No |
|
What is the next card that the ALC goes to after it leaves the 1A1A1A10? |
1A1A1A9 Distribution Board |
|
In normal operation, with nothing faulty, what logic level should be seen at 1A1A1A10 J1? |
5 VDC |
|
What does BITE 12 monitor? |
VSWR |
|
Does FM plain voice pass through the 1A1A15 AM detector? |
Yes |
|
Does AM plain voice pass though the 1A1A14 FM detector? |
No |
|
Which BITE signals leave the 1A1A15 and go directly to the 1A1S5B? |
15,16 |
|
BITE 17 enters the 1A1A21 as 1.2 KHz and leaves as........ |
RF Noise |
|
If the EMP Protect SW on the 1A1A21 goes bad, would there be any noticeable indications? |
Only if a nuclear bomb was detonated nearby |
|
When conducting BITE tests 13, 14, 15, or 16, 1A1A18 P1-14 should read what logic level? |
High (12 VDC) |
|
With a receive RF frequency of 250 MHz what will the 1st L.O. frequency be? |
320 MHz |
|
With a receive RF frequency of 320 MHz what will the 1st L.O. frequency be? |
390 MHz |
|
What is the frequency of the 1st I.F.? |
70 MHz |
|
What is the frequency of the 2nd L.O.? |
44.5 MHz |
|
Which module contains the BITE detector for BITE 14? |
1A1A16 |
|
BITE 16 and FM IF leave the 1A1A16 at what point? |
P7 |
|
A logic level low (-11 VDC) at 1A1A14 P1-2 will cause the FM output gate to... |
Shut Off |
|
A logic level low at 1A1A12 P1-22 will cause what to be seen on J2? |
1.2 KHz Square Wave |
|
A logic level high (6.2 VDC) at 1A1A12 P1-30 will cause what to be seen on J3? |
Logic Level Low |
|
When transmitting, what signal is present at test point 1A1A9 A2J11? |
Logic Level Low (Ground) |
|
With a logic level low at the input of 1A1A8 P1-14 what mode of operation will be selected? |
Transmit |
|
Which BITE tests require the use of 1A1S7 (Test Key)? |
10, 11, 12 |
|
1A1A23 is the reference designator of which module? |
RF Oscillator |