Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
124 Cards in this Set
- Front
- Back
What is the width of a PEL line? |
4 Inches |
|
What is the periodicity of ESD compliance inspections? |
Annual, except during LCI years. |
|
What is the periodicity of ESD Logistics Compliance Inspections? |
Triennial (Every 3 years) |
|
What is a Type 1 Radhaz Sign used for? |
Advised personnel of an RF hazard. Shall be posted at the boundary of an area, being which the PEL may be exceeded. |
|
What is a Type 2 Radhaz Sign used for? |
Excludes personnel from proceeding past a designated point. |
|
What is a Type 3 Radhaz Sign used for? |
Informs personnel that contact current and/or RF burn hazards may exist on metallic objects in this area. |
|
What is a Type 4 Radhaz Sign used for? |
Informs personnel that an RF hazard exists and to check with commands authority prior to fueling operations. |
|
What is a Type 5 Radhaz Sign used for? |
Provides a blank area in which special instructions necessary for safe operations can be specified. |
|
Which type of Radhaz sign has a blank area for writing special instructions? |
Type 5 |
|
What constitutes a Category 4 CASREP? |
Total loss of one current mission and unable to operate as directed by TACON and/or significant risk to cutter/crew survivability, which outweighs the gain in mission execution. |
|
What constitutes a Category 3 CASREP? |
A major degradation in the primary mission. |
|
What constitutes a Category 2 CASREP? |
Partial degradation in any primary mission or major degradation or complete loss of a secondary mission. |
|
How often does an ESD Compliance inspection occur? |
Annually, except during LCI years. |
|
How often does an ESD Logistics Compliance Inspection occur? |
Triennially (every 3 years) |
|
During an ESD Supervisor relief, the ESD Compliance checklist must be completed. How long does the new Supervisor have to report discrepancies? |
14 days |
|
Following an ESD Compliance inspection, how long does the ESD have to submit a plan to correct discrepancies? |
30 days |
|
What is the Cognizant code for DOD Mandatory Turn-in Parts? |
"7" |
|
What is the Acquistion Advice Code for DOD Owned parts? |
D |
|
What is the code for MTI parts?
|
XB |
|
What funds are used by CGTEP to pay for calibration? |
AFC-30 for CG equipment. AFC-80 for NTNO. |
|
What funds does the CGTEP use to replace Test Equipment? |
AFC-42 |
|
What does a unit that participates in the CGTEP have to pay for? |
Shipping to (not from) the Loan Pool or Calibration facility. |
|
When an ESD is assigned responsibility for a new asset, how does the ESD request Test Equipment for the Asset's maintenance? |
Submit an ACR (allowance change request) with justification from new asset's maintenance requirements. |
|
Who is responsible for supplying Test Equipment for new systems? |
The Core Technology or Product Line introducing the new system. |
|
How far outside of the drip range must ground rods be installed? |
2-6 feet (0.6-1.8meters) extending 125 feet (37.5) meters) |
|
How often is an Ordnance Technical Inspection conducted? |
18 months with NTNO ordnance equipment, annual otherwise. |
|
How soon does a re-inspection have to be conducted if Major or Multiple discrepancies are discovered during the Ordnance Technical Inspection? |
90 days |
|
How long once reporting aboard a cutter does a new technician have to complete indoctrination? |
2 months |
|
Who has authority to approve an engineering change to begin the TCTO process? |
Surface Forces Configuration Control Board (SFCCB) |
|
A booking chit for Article 134 must articulate a violation of one of ___ aspects. |
Good Order and Discipline |
|
In an area where exposure exceeds ___ times the PEL warning lights are required. |
10 times |
|
Antenna resistance measurements are recorded on what document? (form number of an antenna resistance card) |
NAVSEA 9210/19 |
|
What reading, in megohms, indicates a good antenna? |
200 megohms |
|
An antenna with a megohm reading of ____ or less requires emergent attention. |
5 megohms |
|
When applying a correction of 5 degrees on a heading sensor, what light indication displayed?
|
No Lights |
|
When performing a SOVT, if the Transducer has a light illuminated on top... What is this an indication of? |
Proper Operation: flashes every 2 seconds |
|
How long do you have to return an MTI part upon receipt? |
48 Hours
|
|
Upon receiving a SPETRL, how long do you have to verify and submit it? |
2 Weeks |
|
How far from an exterior wall does a shielded red cable need to be? |
1 Meter (39.3Inches) |
|
If placed in the same rack, how far away from each other does red and black processing equipment need to be? |
30cm |
|
How far apart do a shielded black and red cable have to be if they run parallel for 30 meters? |
15cm |
|
Who signs a technician's travel card? |
The EPO or designated representative |
|
If a technician borrows a tool from a station's tool program and loses it, who does the final disposition go to?
|
The station. Report to ESD MS as well.
|
|
After how many days does a CASREP have to be updated? |
30 |
|
How many hours after a casualty do you have to submit a CASREP? |
24
24 hours if it cannot be repaired in 48. |
|
If a unit which is not currently part of the CGTEP wishes to join the CGTEP, what must they do? |
Apply and turn over AFC-30 funds budgeted for unit test equipment calibration. |
|
What does the CGTEP not pay for in regards to supported units? |
Shipping to Loan Pool or calibration facility (CGTEP pays for shipping back to unit) |
|
What is the length of a standard copper clad steel grounding rod? (In meters) |
1.90cm (3/4 in) diameter and 3 meters (10 feet) |
|
How many travel cards are generated for an ESD traveling to support an unmanned unit? |
One travel card for unmanned sites. One per trip leg for manned sites. |
|
How many travel cards are generated for an ESD traveling to support 2 manned units then returning to the ESD? |
3. One for each leg of the trip. |
|
How often must the resistance of a building's ground system be checked? |
Annually |
|
After applying a thin layer of Anti-Seize to a bolt and nut, what torque value must be applied to a ground system. Example: Harris Subsystem |
25 foot-pounds |
|
What type of test equipment would a multimeter that does not appear as a SCAT on a MPC be?
Note: It must also be labeled "For corrective maintenance only" |
FSTER Fleet Supplemental Test Equipment Requirement |
|
What items are required for a Tool Control Log?
|
Blank Log Sheets All Completed Log Sheets for the last 3 years Copies of all tool inventory sheets Blank Missing Tool Reports All pending and completed Missing Tool Reports for the past 3 years Method to record MS routine inventories and spot checks |
|
How long must 1149's be kept? |
3 fiscal years plus current year |
|
What items does the 1149 document number consist of? |
DODAAC, Julian date and requisition serial number. Coast Guard uses OPFAC for DODAAC |
|
What is the bulk allowed for a male's hair? |
1 1/2 inches
|
|
After submitting a MILSTRIP what must be recorded?
|
Z- Document Number |
|
What can a woman not have for nails in uniform?
a. Blue Nail Polish b.Nails longer than 1/4" d. Straight Shaped Nails |
Blue Nail Polish |
|
Which would be an improper choice of ribbons in Winter Blues?
|
All Up to nine of wearer's choice Three highest precedence ribbons authorized |
|
Which manual outlines voluntary education opportunities? |
COMDTINST M1500.10C |
|
How many months does the G.I. bill pay?
|
36 Months |
|
What are the four aspects that a good fitness plan addresses?
Muscle Strength, Flexibility, Cardiovascular health and _________ |
Body Composition |
|
Hearing test results stay in a member's record for the duration of employment plus how many years? |
. |
|
Who can authorize a permanent shaving chit? |
. |
|
Who can authorize a variation from the uniform of the day after conferring with competent medical authority?
|
. |
|
What is the power output range of an XTL-5000 at high power? |
20-25W |
|
What is the first corrective step if an XTL-5000 is outside of the proper power range? |
Reprogram transceiver |
|
What is the first corrective step if an XTL-5000 is more than 1% audio frequency deviation? |
Replace the mic |
|
What should you do if an SPS50 has good HV power and magnetron heater voltages but has low magnetron current? |
Replace magnetron |
|
What actions require QA checks in ALMIS? |
Corrective Actions |
|
During an ODU inspection, which would be considered a discrepancy?
a. Black unadorned sunglasses b. duty cell phone clipped to the belt |
. |
|
What tensile strength must all tower hardware be rated to? |
5000 for climbing gear. Probably the same |
|
What is the maximum free-fall distance that fall-arrest equipment can allow? |
6 feet |
|
A direction finder can be up to ____ degrees off before requiring re-calibration. |
+/-30 degrees |
|
When measuring a Direction finder's antenna. If you measure from the antenna to dipole and obtain a measurement of 9.5 megohms what should you do? |
Clean and re-measure If still less than 10 megohms, replace. |
|
How far can a topside shielded cable go before needing additional grounding? |
18 inches |
|
Who must the Maintenance Supervisor designation letter be provided to?
|
BOD ? |
|
What does Scat Priority Code 96 mean? |
Equipment is obsolete (Option on test is worded about military use/function) |
|
Where is the Maintenance Due list located in ALMIS? |
Decision Support Systems 4.5 |
|
What are "BK_" Series codes used for?
|
To track returns |
|
How long are completed MPC cards retained for? |
1 year |
|
How long does an ESD Compliance Inspection have to provide the results? |
. |
|
What funds are used to remove obstructions during dry dock? |
. |
|
What is the form number for an out of calibration tag? |
. |
|
Metal structures within ____ feet of a down rod most be tied into the ground system? |
. |
|
What chapter are punitive actions in? |
. |
|
What does SINAD test? |
. |
|
What is the frequency deviation tolerance for an audio test on the xtl-5000? |
. |
|
The function of a TDR in sending signals down the line and waiting for a return signal is most like a _____? |
Radar? |
|
What is the term for when sea time, surf time, and points begin accruing? |
Point Start Date |
|
What is the form number for a report of offense? |
CG-4910 |
|
How far can a topside double shielded cable go without additional grounding? |
. |
|
If a black and red cable travel alongside for 30m how far must they be separated by? |
. |
|
How far most a black and red power cable be separated? |
. |
|
At what voltage must you have a safety observer to work on equipment? |
. |
|
What is included in the man labor hours in ALMIS? (Time spent doing what would not be included) |
. |
|
Who is responsible for changing an asset's status to NMCM during long availabilities? |
. |
|
During an Electronics Technical Assessment what is provided to the port engineer to inclusion into the drydock package? |
. |
|
What is the text book definition of binge drinking? |
. |
|
When are staff symbols required in the To line of a memo? |
. |
|
How often should a downloaded PMS deck be validated? |
. |
|
How often most antennas and transmission cables be tested at a shoreside facility? |
. |
|
What alternate piece of equipment can be tested with a megger? a. Whip Antenna b. UHF/VHF Antenna c. Wire Antenna d. HF Antenna |
. |
|
If IFF calibration lapses, how is the calibration renewed? |
SESEF range |
|
What funds are used to complete TCTOs at drydock? |
. |
|
What goes on a Report of Offense? a. Education b. EMPLID c. Social security number |
. |
|
What UCMJ article would a person helping a deserter be charged under? |
92 ? |
|
What is the frequency of the SPS-50 X-band? |
9Ghz |
|
What is the frequency of the SPS-50 S-band? |
3Ghz |
|
What is the minimum priority that an underway cutter may send a CASREP as?
a. Z b. R c. P d. U |
c. Priority ? |
|
What division at BCD provides training and fleet trend analysis? |
FSD? |
|
Who does a QA designation letter get provided to? |
. |
|
What is the maximum number of recipients in an email "TO" line? |
. |
|
Large projects should be broken up into actionable chunks that should take no longer than ___ hours to complete.
|
(from the Process Improvement Guide) |
|
When installing an LS571 Transducer, how long must the QA wait to inspect for leaks?
|
3 Hours |
|
The RF transmission cable of a piece of equipment must be separated from other cables by how far? (except where it enters the equipment)
|
.
|
|
How far must red and black power cables be separated?
|
.
|
|
How many safety features does the SIG have?
|
.
|
|
How many trigger functions does the SIG have?
|
. |
|
How long do unit training plans have to be retained?
|
2 years |
|
How many elements does a unit training plan consist of?
|
5 distinct elements Formal Schools, Mandated Training, Individual Qualifications, Drills/Exercises, Professional Development |
|
What is the VA GI Bill pay out based on? a. number of credits being taken b. average housing for the state (some other options that I cannot recall) |
|
|
How long does QA need to wait to check for leaking on the FS something transducer?
|
3 Hours |