Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
27 Cards in this Set
- Front
- Back
In the toolpath chainmanager: selecting chains in a certain order has no effect on the toolpath outcome (true or false) |
False |
|
when creating an efficient toolpath, the programmer should consider how much the tool is machining in air. (true or false) |
True |
|
When programming a new setup from a different plane, it is best to create a new WCS and leave the part at its original orientation. (true or false) |
True |
|
A viewsheet can use bookmarks to set an active WCS. (true or false) |
True |
|
You can merge geometry files in mastercam using the File, Merge function. (true or false) |
True |
|
Viewsheet bookmarks can can make levels visible and active. (true or false) |
True |
|
In a toolpath's parameters dialog box, use the preview toolpath button to: A. Hide all toolpaths except the one you are working on. B. Check that your linking parameters are correct. C. Both A and B. D. Neither. |
B. Check that your linking parameters are correct. |
|
Viewsheet bookmarks can: A. Set active view B. Set Visible levels C. set active WCS D. All of the above |
D. All of the above |
|
A vewsheet can use bookmarks to save a certain graphics view. (true or false) |
True |
|
You can preview your toolpaths before exiting teh 2D toolpath dialog box. (true or false) |
True |
|
The Radial Chip Thinning (RCTF) allows for: A. longer tool life B. Use the entire flute length C. Less tool deflection D. All of the above |
D. All of the above |
|
For a toolpath to be valid, you must visit and edit each page of the parameters dialog box. (true or false) |
False |
|
The radial chip thinning factor is based on: A. Chipload B. Step over C. Feed per minute D. Depth of cut |
A. Chipload |
|
On the linking parameters page for for the contour toolpath, when depth is set to incremental that means:\ A. It is measured from the bottom of the part B. It is relative to the location of the origin C. It is relative to the location of the chained geometry D. It is measured from the origin 0,0,0 |
C. It is relative to the location of the chained geometry. |
|
You can translate only one entity at a time. (true or false) |
False |
|
when using the file, merge function. you can reselect the position of the file to be merged when using the file merge function. (true or false) |
True |
|
use the verify feature to: A. Ensure that your part's geometry is valid B. inspect operations to find areas that need to be machined or possible gouges C. check that the toolpaths are displayed on the part D. None of the above |
B. inspect operations to find areas that need to be machined or possible gouges |
|
When copying an operation in the toolpaths manager, it is best if the source operation is similar to the toolpath you want to create. (True or false) |
True |
|
In machine group properties which box needs to be checked to show stock? |
display |
|
When copying operations in the tool path manager you should: |
be sure to edit the comment so it matches the new one. |
|
large stepovers create thinner chips and lowers chipload (T or F) |
False |
|
the mastercam standalone tool manager will open a new session for every tool library open (T or F) |
True |
|
Mastercam help in non context sensitive |
False |
|
Which tool path motion directly proceeded dynamic motion? |
Part geometry offset base |
|
On the linking parameters page for the contour toolpath, when depth is set to incremental that means: |
It is relative to the location of the chained geometry |
|
if you edit an operation and use preview toolpath, it is necessary to regenerate the operation to make it clean (T or F) |
False |
|
In the level manager, what function do you use to remove empty levels: |
purge empty levels |