Aviation Maintenance Ratings (Chapter 03 - Aviation Supply)

Front 1

State the composition of the Project code.

Back 1

Alpha/alpha/numeric.

Front 2

What FAD is assigned to most fleet operating activities?

Back 2

FAD II or III

Front 3

Aircraft repair usage statistics are used by the supply department for what purpose?

Back 3

Usage statistics justify stocking replenishment parts.

Front 4

What are the two types of part numbers?

Back 4

Definitive and non-definitive.

Front 5

What is the correct nomenclature for what is commonly referred to as the “manufacturer’s code?”

Back 5

Commercial and Government Entity Code (CAGE).

Front 6

What term is used for a part, component, or system in which the requisitioned part is used?

Back 6

Next higher assembly.

Front 7

What are the two primary technical manuals used by the maintenance technician to order replacement parts?

Back 7

The illustrated parts breakdown (IPB) and the maintenance instruction manual (MIM).

Front 8

What information is contained in the "Introduction" of the IPB?

Back 8

General information and instructions for using the publication.

Front 9

What part of the IPB contains information concerning detailed parts that make up a component?

Back 9

The group assembly parts list.

Front 10

What position(s) of the SM&R code indicate(s) the source from which you can acquire the item?

Back 10

The first position.

Front 11

Which NAVSUP publication provides cross-reference information from a reference number to its national stock number (NSN)?

Back 11

Master Cross-Reference List (MCRL).

Front 12

What NAVSUP publication provides information on exceptions to the one-for-one turn-in rule?

Back 12

Consolidated Remain in Place List (CRIPL).

Front 13

How often is the ICRL-A revised?

Back 13

Quarterly.

Front 14

What is the purpose of the Aviation Consolidated Allowance List (AVCAL)?

Back 14

AVCAL lists the items & quantities of aeronautical material authorized to be stocked by an aircraft carrier to support the maintenance and operations of embarked aircraft.

Front 15

What are the first two-digits of the nine-digit NIIN called?

Back 15

The National Codification Bureau (NCB) code.

Front 16

What two instructions describe the procedures for allowance and inventory of the AMMRL program?

Back 16

NAVAIRINST 13650.1 for IMRL items and
NAVAIRINST 13630.1 for tailored outfitting list (TOL) items.

Front 17

How is Naval Air Systems Command (NAVAIRSYSCOM) involved in the AMMRL program?

Back 17

NAVAIRSYSCOM exercises overall program management and authority.

Front 18

What are the five major sections of the IMRL?

Back 18

Employment data, change list, index, main body, and the activity inventory record.

Front 19

What section of the IMRL lists all of the items allowed for the activity along with allowance quantities?

Back 19

The IMRL main body.

Front 20

How often is the IMRL Activity Inventory Record reissued?

Back 20

It is reissued in its entirety each month.

Front 21

What work center is the point-of-contact for parts and material at the organizational maintenance level?

Back 21

Material control.

Front 22

DD form 1348, Standard Form 44, and an identiplate (DD 1896 or 1897) are all issued as part of what package?

Back 22

A flight packet.

Front 23

What level of maintenance orders the greater volume of parts?

Back 23

Intermediate level.

Front 24

The Individual Component Repair List (ICRL) is used by what work center to determine the repair capability of a component received by supply?

Back 24

Aeronautical material screening unit (AMSU).

Front 25

What are the two sections of the Aviation Support Division/Supply Support Center (ASD/SSC)?

Back 25

Supply Response Section (SRS) and Component Control Section (CCS).

Front 26

If a part is listed in the CRIPL, the maintenance activity has how many hours after receipt of the replacement component to furnish the unserviceable part?

Back 26

24 hours.

Front 27

What items are maintained in the pre-expended bins (PEBs)?

Back 27

High usage, low-cost, maintenance-related consumable materials that have a minimum demand frequency of three per month.

Front 28

How often does supply review stock records for the PEB?

Back 28

Quarterly.

Front 29

What section of Aviation Support Division/Supply
Support Center (ASD/SSC) manages local repair cycle assets (LCRA)?

Back 29

Component control section (CCS).

Front 30

How many workload priorities can be assigned to a LRCA storage unit?

Back 30

Four.

Front 31

If a squadron requisitions an NMCS component and the only other part on station is in the IMA for repair, what priority will be assigned?

Back 31

Priority 1, and the part would be designated "EXREP" or expeditious repair.

Front 32

What is the purpose of an illustrated parts breakdown?

Back 32

To allow supply and maintenance personnel to identify and order replacement parts for aircraft or equipment

Front 33

Information from which of the following sources is used by supply department personnel as justification for stocking material?

Back 33

Usage statistics

Front 34

What type of code identifies the agent or agency that has design control over an item?

Back 34

CAGE

Front 35

What section in an IPB contains general information and instructions for using the publication?

Back 35

Introduction

Front 36

Besides the introduction, each IPB includes what basic information?

Back 36

Table of contents or alphabetic index
Group assembly parts list
Numerical index

Front 37

What section of the IPB contains an explanation of the source or SM&R codes used in the IPB?

Back 37

Introduction

Front 38

What listing in the IPB lists aircraft assemblies and identifies the pages or figure numbers where the assemblies are shown in the IPB?

Back 38

Alphabetical index

Front 39

What section of the IPB contains a description of a component listed in the IPB?

Back 39

Group assembly parts list

Front 40

What section of the IPB lists supplementary handbooks to which you may refer?

Back 40

Introduction

Front 41

What is the purpose of an index number in an IPB?

Back 41

To establish the relationship between parts in the illustration and the corresponding parts list

Front 42

An SM&R code is an alphanumeric code containing how many digits?

Back 42

Five or six.

Front 43

What part of a part’s SM&R code indicates how the part is to be acquired?

Back 43

Source code only

Front 44

What position of the SM&R code identifies the maintenance level assigned to completely repair an item?

Back 44

Fourth

Front 45

What Aviation Supply Office (ASO) publication contains a complete list of Navy-managed material that is classified as mandatory turn-in repairables (MTR)?

Back 45

Master Repairable Item List (MRIL)

Front 46

What information does the third position of an SM&R code provide?

Back 46

The lowest maintenance level authorized to remove, replace, and use an item

Front 47

What two instructions govern policies, procedures, and definitions applicable to SM&R codes?

Back 47

NAVSUPINST 4423.14 and NAVAIRINST 4423.3

Front 48

When removal of a component from an aircraft is not feasible or advisable until a replacement is on hand, its part number is listed in what document?

Back 48

Consolidated Remain In Place List (CRIPL)

Front 49

What type of material is listed in the Consolidated Remain In Place List (CRIPL)?

Back 49

Material exempt from the one-for-one turn-in rule

Front 50

The reference number on a master cross reference list refers to what number or numbers?

Back 50

Either a manufacture’s part number, a drawing number, or a design control number

Front 51

The Master Cross-Reference List (MCRL) is used to provide a cross reference between what items of information?

Back 51

Reference number and NSN

Front 52

What is the purpose of the ICRL-A?

Back 52

To provide a list of repairables and the local IMA's capability to repair them

Front 53

An ICRL-A is revised at what specified interval?

Back 53

Quarterly

Front 54

What ICRL Capability code is used for check and test only?

Back 54

A1

Front 55

Within the ICRL listing, what code is equivalent to Beyond Capability of Maintenance (BCM)-3?

Back 55

X3

Front 56

To what reference should you refer to obtain an NSN or reference number for an item when you only know the description?

Back 56

Afloat Shopping Guide (ASG)

Front 57

What is the 13–digit number called that identifies an item of material in the supply system?

Back 57

National stock number (NSN)

Front 58

What is the title of the overall program that provides the data required for effective management of support equipment at all levels of maintenance?

Back 58

Aircraft Maintenance Material Readiness List (AMMRL) program

Front 59

What command exercises overall program management for the AMMRL program?

Back 59

NAVAIRSYSCOM

Front 60

What information is provided by the first two digits in the FSC code number?

Back 60

Manager that controls the category of material

Front 61

The NSN is comprised of what total number of digits?

Back 61

13

Front 62

Which of the following acronyms identifies equipment that is required on the ground to make a system, subsystem, or end item of equipment operational?

Back 62

SE

Front 63

Within an activity, personnel in what rating normally maintain the IMRL?

Back 63

LS

Front 64

The IMRL contains how many major sections?

Back 64

Five

Front 65

At the organizational maintenance level, the point of contact for all material requirements generated by a squadron is located in what organization?

Back 65

Material control center

Front 66

What Material Condition code tells you that an item of supply is fast moving and in high demand?

Back 66

F

Front 67

To determine whether an intermediate maintenance activity has capability to test/check or repair an item, what I-level supply area screens all components turned into ASD/SSC?

Back 67

Aeronautical Material Screening Unit (AMSU)

Front 68

The Aviation Support Division/Supply Support Center (ASD/SSC) is composed of what section or sections?

Back 68

supply response section (SRS) and
the component control section (CCS).

Front 69

The supply response section (SRS) limits the quantity of any item in the pre-expended bin to a supply of how many days?

Back 69

30-days

Front 70

Within an activity, what officer must approve the item of PEB stockage when it costs more than $150?

Back 70

The commanding officer

Front 71

Supply will remove an item from the PEB if there has been no demand for the item within what total period of time?

Back 71

12 months

Front 72

What is the purpose of the component control section (CCS) within the supply department?

Back 72

To manage the LRCA at the ASD/SSC
(Aviation Support Division/Supply Support Center)

Front 73

A local repair cycle assets (LRCA) is assigned a workload priority. The priority assigned is one of what total number of priorities that can be assigned to the LRCA?

Back 73

Four

Front 74

An aircraft is in NMCS/PMCS status. What priority is assigned to an LRCA in support of this aircraft?

Back 74

Priority 1