As Rate March 2016 Advancement Exam

Front 1

The A/M32C-21 is designed to provide what for electronic equipments?

Back 1

Ventilation, dehumidification, cooling, and filtration

Front 2

Which parts of an aircraft does the A/M32C-21 provide cooling for?

Back 2

Cabins and equipment compartments

Front 3

The A/M32C-21 is mobile, _____-mounted, _____-powered, and self-contained.

Back 3

Trailer-mounted; Electric-powered

Front 4

The A/M32C-21 is powered by a ___ volt, ___ phase, ___ Hz electric motor.

Back 4

440 volt; 3 phase; 60 Hz

Front 5

The refrigerant system of the A/M32C-21 uses an accessible _____, ___ cylinder compressor, and a drive motor in a _____ housing.

Back 5

Hermetic; six cylinder; single housing

Front 6

Maximum towing speed capacity of the A/M32C-21

Back 6

15 mph

Front 7

Type of refrigerant used on the A/M32C-21

Back 7

R-22

Front 8

Cooling capacity of the A/M32C-21

Back 8

23 tons

Front 9

Operating ambient limits of the A/M32C-21

Back 9

0-100 °F

Front 10

A/M32C-21 condenser type

Back 10

Two tubes and a fin

Front 11

The drive motor of the A/M32C-21 condenser fan is a ___ horsepower, ___ volt, ___ phase, ___ Hz electric motor.

Back 11

10 horsepower; 440 volt; 3 phase; 60 Hz

Front 12

If the head pressure of the A/M32C-21 condenser coil drops to ___ psig, the condenser fan will cut out to reduce amount of condensing.

Back 12

175 psig

Front 13

A ___ KVA transformer is used to lower the voltage from ___ VAC to ___ VAC of the A/M32C-21.

Back 13

0.3 KVA; 440 VAC to 110 VAC

Front 14

The A/M32C-21 unit is started by placing the MODE switch in the ______ position.

Back 14

Vent

Front 15

The A/M32C-21 supplies conditioned air at temperatures greater than ___ °F to dehumidify.

Back 15

90°F

Front 16

On the A/M32C-21, the fan cycling switch closes and the condenser fan operates at compressed pressures greater than ___ psig.

Back 16

245 psig

Front 17

The A/M32C-21 provides cool, dry conditioned air at ___ °F.

Back 17

45 (+/- 5) °F

Front 18

The maximum dewpoint temperature of the A/M32C-21 is ___ °F.

Back 18

40°F

Front 19

The A/M32C-21 is designed to deliver conditioned airflows up to ___ pounds per _____.

Back 19

100 lbs per minute

Front 20

What is the nomenclature of the nancart?

Back 20

A/M26U-4B

Front 21

When not in use, the A/M26U-4B shall be parked with the _____ removed and placed in the _____, the swivel caster in the _____ position, and parking brake engaged.

Back 21

Jack removed; placed in the toolbox; full down position;

Front 22

The A/M26U-4B is normally shipped in what condition?

Back 22

Fully assembled, lubricated, tires inflated, and all components operational

Front 23

Proper inflation of the A/M26U-4B front and rear tires.

Back 23

35 psig front; 65 psig rear

Front 24

Do not charge the A/M26U-4B system nor interchange any components with _____.

Back 24

Oxygen components

Front 25

Do not use the A/M26U-4B to purge _____ components or systems.

Back 25

Oxygen

Front 26

Do not use the A/M26U-4B to charge nor purge systems that require an _____ source of nitrogen.

Back 26

Oil-free

Front 27

The A/M26U-4B cylinders is charged with _____ nitrogen.

Back 27

Oil-free

Front 28

The nitrogen cylinders on the A/M26U-4B can be shipped in what condition?

Back 28

Fully charged

Front 29

The nitrogen cylinders of the A/M26U-4B can be charged up to ___ psig.

Back 29

3500 psig

Front 30

What is the commercial item description of the gaseous nitrogen used for recharging the A/M26U-4B?

Back 30

Type 1 (gaseous), Class 2 (oil tolerant), Grade B (99.5% pure, low moisture content)

Front 31

What is the first step for recharging the cylinders of the A/M26U-4B?

Back 31

Ensure all six cylinder manifold lever control valves are CLOSED.

Front 32

What must be completed before the operational test is performed on the A/M26U-4B?

Back 32

Servicing and charging

Front 33

When not in use, how is the A/M26U-4B parked or stowed?

Back 33

Jack removed and placed in toolbox, swivel caster in full down position, and parking brake engaged

Front 34

Which pub should be consulted to prepare the A/M26U-4B unit for air shipment?

Back 34

NAVSUP PUB 505

Front 35

The A/M26U-4B pump motor valve controls nitrogen flow from the _____ to the _____.

Back 35

Manifold Assembly to Boost Pump Preset Regulator

Front 36

What does the Booster Air Drive Pressure Gauge indicate in the A/M26U-4B?

Back 36

Nitrogen air pressure at motor inlet [0-200 psig]

Front 37

What is the range of the A/M26U-4B high pressure outlet gauge?

Back 37

0 to 5000 psig

Front 38

What is the range of the A/M26U-4B low pressure outlet gauge?

Back 38

0 to 600 psig

Front 39

What is the pub for A/M26U-4B?

Back 39

AG-750AO-OMM-100

Front 40

To prevent equalization of cylinder pressure of the A/M26U-4B unit, how many cylinder manifold lever control valves may be opened at a time?

Back 40

Only ONE

Front 41

The A/M26U-4B pump will stop automatically when regulator inlet pressure gauge reaches ___ psig.

Back 41

3500 psig

Front 42

A/M26U-4B pump drive pressure must be at least ___ psig.

Back 42

117 psig

Front 43

What does CSE stand for?

Back 43

Common Support Equipment

Front 44

What does PSE stand for?

Back 44

Peculiar Support Equipment

Front 45

What does TPDR stand for?

Back 45

Technical Publications Deficiency Report

Front 46

Which form is used to report a TPDR?

Back 46

OPNAV 4790/66

Front 47

What is a Warning?

Back 47

Operating procedure, practice, or condition which may result in injury or death

Front 48

What is a Caution?

Back 48

Operating procedure, practice, or condition which, if not strictly observed, may damage equipment

Front 49

What is a Note?

Back 49

Operating procedure, practice, or condition which is essential to emphasize

Front 50

"Shall" has been used only when application of a procedure is _____.

Back 50

Mandatory

Front 51

"Should" has been used only when application of a procedure is _____.

Back 51

Recommended

Front 52

"May" and "need not" have been used only when application of a procedure is _____.

Back 52

Optional

Front 53

"Will" has been used only to indicate _____.

Back 53

Futurity

Front 54

_____ are performed to verify a unit of SE is properly serviced and ready for use.

Back 54

Preoperational inspections

Front 55

Preoperational inspections are documented on which record?

Back 55

OPNAV 4790/52

Front 56

AIMD

Back 56

Aircraft Immediate Maintenance Department

Front 57

PKP

Back 57

Potassium Bicarbonate

Front 58

TYCOM

Back 58

Type Commander

Front 59

What is MIL-STD-882?

Back 59

System Safety Program

Front 60

Licensing shall be in accordance with _____ and _____ instructions.

Back 60

OPNAV 4790.2 and TYCOM

Front 61

The Chief of Naval Operation's "safety officer" is the _____.

Back 61

Commander of the Naval Safety Center

Front 62

Approach/Mech magazine is published ___ times a year.

Back 62

Four

Front 63

_____ is published bi-monthly to help people enhance their professional development with the NAVY.

Back 63

Safetyline

Front 64

_____ is the primary goal of a survey.

Back 64

Safety

Front 65

_____ reporting is the single most important way of preventing accidents that has happened before.

Back 65

Mishap reporting

Front 66

An accident report is sent to the _____ once an accident has been investigated.

Back 66

Naval Safety Center

Front 67

What does NSC stand for?

Back 67

Naval Safety Center

Front 68

Which form is used to report misuse and abuse?

Back 68

OPNAV 4790/108

Front 69

Who has the ability to revoke an SE operation's license?

Back 69

Commanding Officer

Front 70

_____ is chief among uncontrollable hazards.

Back 70

Weather

Front 71

What is the maximum noise level exposure that BUMED has established?

Back 71

85 dBA

Front 72

Maximum aircraft weight that the tow tractor can pull is ___ times the drawbar pull.

Back 72

10 times

Front 73

Fixed polyurethane chock blocks are used on _____ SE.

Back 73

Shipboard

Front 74

Polyurethane chock blocks joined by a line are used on _____ SE.

Back 74

Landbased

Front 75

What is the primary part number for a shop ambient oxygen monitor?

Back 75

3622AS100-1

Front 76

At which temperature does air condensation occur?

Back 76

-317° F

Front 77

What is the composition of air condensing into the liquid nitrogen container?

Back 77

50% oxygen, 50% nitrogen

Front 78

What is the boiling point of the liquid nitrogen?

Back 78

-321° F

Front 79

_____ are caused by thermal contraction of materials.

Back 79

Thermal stresses

Front 80

Smoking, flames, sparks, or combustible materials should be avoided within ___ feet of liquid oxygen.

Back 80

50 feet

Front 81

Keep the oxygen concentration in the air between ___ and ___ percent when handling liquid oxygen.

Back 81

18-24%

Front 82

Two types of nitrogen systems contamination

Back 82

Solid particulates and hydrocarbons

Front 83

Type 1 oxygen is ______

Back 83

gaseous oxygen

Front 84

Type 2 oxygen is ______

Back 84

liquid oxygen

Front 85

Grade _____ oxygen is used in fuel cells which requires a 99.995% purity.

Back 85

Grade A

Front 86

Grade _____ oxygen is used for breathing purposes.

Back 86

Grade B

Front 87

Grade _____ oxygen is used as a propellant.

Back 87

Grade C

Front 88

Contamination limits for breathing oxygen is governed by Military Standard MIL____________

Back 88

MIL-PRF-27210

Front 89

_____ cleaners are usually employed as heated baths.

Back 89

Alkaline cleaners

Front 90

Publication for SE corrosion control

Back 90

NA 17-1-125

Front 91

Publication for Aviation Hose and Tube Manual

Back 91

NA 01-1A-20

Front 92

Publication for cleaning and corrosion control

Back 92

NA 01-1A-509 series

Front 93

Publication for SE Storage Batteries

Back 93

NA 17-15BAD-1

Front 94

NAMP Publication

Back 94

COMNAVFORAIRINST 4790.2

Front 95

Corrosion is the _____ deterioration of metal because of its reaction with the surrounding environment.

Back 95

electrochemical

Front 96

_____ is a liquid solution containing ions.

Back 96

electrolytes

Front 97

The _____ is a dissimilar conductive material that has less tendency to corrode than the anode.

Back 97

cathode

Front 98

An _____ contact between anode and cathode must exist for electrons to move.

Back 98

electrical

Front 99

_____ results from direct chemical attack on metal surface that proceeds uniformly over the entire exposed surface.

Back 99

Uniform surface corrosion

Front 100

_____ corrosion occurs when different metals are in contact with each other.

Back 100

galvanic corrosion

Front 101

_____ corrosion leaves a white or gray powdery deposit that blotches the surface.

Back 101

Pitting corrosion

Front 102

_____ corrosion is an attack on the grain boundaries of a metal.

Back 102

Intergranular corrosion

Front 103

_____ corrosion occurs when the surface grains of a metal are lifted up by force of expanding corrosion products occurring at the grain boundaries.

Back 103

Exfoliation corrosion

Front 104

_____ occurs when the electrolyte in a crevice has a different concentration than the area adjacent to the crevice.

Back 104

Crevice corrosion

Front 105

_____ is the intergranular cracking of a metal caused by the combined effects of constant tensile stress and corrosion.

Back 105

Stress corrosion cracking

Front 106

_____ corrosion is a special form of crevice corrosion that occurs on metal surfaces having an organic coating system.

Back 106

Filiform corrosion

Front 107

_____ corrosion occurs in when corrosion products increase the wear of a surface, and the wear exposes more bare metal surfaces to be corroded.

Back 107

Fretting corrosion

Front 108

_____ corrosion is the increase in the rate of attack on a metal due to the action of a corrosive fluid against the metal surface.

Back 108

Erosion corrosion

Front 109

Low alloy steel corrosion

Back 109

Reddish brown (rust)

Front 110

Aluminum alloy corrosion

Back 110

white to gray powder

Front 111

Stainless steel corrosion

Back 111

red, brown, or black uniform stain

Front 112

Copper, brass, or bronze corrosion

Back 112

blue or blue-green powder

Front 113

chromium corrosion

Back 113

blistering due to rusting

Front 114

Powder coating must be stored in an air conditioned space less than ____ degrees and humidity less than ____%.

Back 114

75 degrees; 50%

Front 115

Recommended cured film thickness for topcoats is from ___ to ___ mils

Back 115

2.0 to 2.5 mils

Front 116

During normal Level ___ and ___ preservation, the clock stops for MRCs and is started again upon depreservation.

Back 116

Level II and III

Front 117

Preservation of SE is recorded on the SE ___________ OPNAV Form ____.

Back 117

SE Custody and Maintenance History Record, OPNAV 5790/51

Front 118

_____ is the combination of two or more metals

Back 118

Alloy

Front 119

_____ is the electrode where corrosion occurs,

Back 119

Anode

Front 120

Publication for Tire and Wheel

Back 120

NA 17-1-129

Front 121

Publication for Tire Inflator Kit

Back 121

NA 17-1-123

Front 122

Low pressure tire kit one is up to ___ psi with ___ psi pop off pressure.

Back 122

80 psi; 100 psi pop off

Front 123

Medium pressure tire kit two is from ___ to ___ psi with ___ psi pop off pressure.

Back 123

80 to 130 psi; 150 psi pop off pressure

Front 124

Tire pressure in excess of ___ psi is tire kit three with pop off valve set ___ psi above maximum required pressure.

Back 124

130 psi; 20 psi

Front 125

For high pressure SE aircraft tires, use a _____

Back 125

nitrogen servicing unit

Front 126

Publication for Diesel Hydraulic Power Supply (DHPS)

Back 126

NA 17-15BF-110

Front 127

Nomenclature of DHPS

Back 127

A/M27T-15

Front 128

The A/M27T-15 is a single system ______ pumping unit with a rated capacity of ____ gpm at ___ psi, and ___ gpm at ___ psi.

Back 128

hydraulic pumping unit; 32 gpm at 3000 psi; 22 gpm at 2000 psi

Front 129

The fluid reservoir of the A/M27T-15 has a capacity of ___ to ___ gallons.

Back 129

25 to 28 gallons

Front 130

The A/M27T-15 has two ___ volt batteries connected in _____.

Back 130

Two 12 volt batteries connected in series

Front 131

The A/M27T-15 has a ____ cylinder ____ cycle turbocharged engine.

Back 131

4 cyclinder 4 cycle

Front 132

Maximum towing speed for the A/M27T-15 is ___ mph.

Back 132

25 mph max

Front 133

Oil capacity of the A/M27T-15 is ___ quarts.

Back 133

11.5 quarts

Front 134

The low pressure filter of the A/M27T-15 uses a ___ micron element.

Back 134

10 micron

Front 135

Two types of pressure switches on the A/M27T-15.

Back 135

Boost pressure, and High pressure

Front 136

The boost pressure switch of the A/M27T-15 opens when pressure drops below ___ psi.

Back 136

below 10 psi

Front 137

The high pressure switch of the A/M27T-15 opens if the supply pressure exceeds ___ psi.

Back 137

Exceeds 1000 psi

Front 138

The high pressure relief valve of the A/M27T-15 opens at ____ psi.

Back 138

5500 +/- 50 psi

Front 139

The firing order of the diesel engine of the A/M27T-15 is ___.

Back 139

1-3-4-2

Front 140

The A/M27T-15 has two ___ gallon tanks.

Back 140

two 11 gallon tanks

Front 141

Publication for the Electric Hydraulic Power Supply (EHPS)

Back 141

NA 17-15BF-120

Front 142

Nomenclature for Electric Hydraulic Power Supply

Back 142

A/M27T-14

Front 143

The A/M27T-14 is supplied with ___ VAC, ___ phase, ___ Hz input power.

Back 143

440/460 VAC, 3 phase, 60 Hz

Front 144

Assembly and disassembly of the A/M27T-14 _____ or _____ is unauthorized.

Back 144

hose or tube disassembly

Front 145

Repair of the A/M27T-14 hose or tube is ______.

Back 145

unauthorized

Front 146

The bleed air flow of the MSU-200 is ___ lb/min

Back 146

204 lb/min

Front 147

A ___ amp generator is attached to the gearbox of the MSU-200 to deliver electrical power.

Back 147

55 Amp

Front 148

The ______ of the A/M27T-14 controls the airflow to the aircraft.

Back 148

Bleed Air Control Valve (BACV)

Front 149

The preoperational checklist for the MSU-200 is found in which publication?

Back 149

NA 19-600-306-6-1

Front 150

The maximum towing capacity of the MSU-200 is ___ mph.

Back 150

15 mph

Front 151

The unit batteries of the MSU-200 will not be able to start the unit if ambient temperature is below ___ degrees F.

Back 151

20 degrees F

Front 152

A _____ is used to supplement external power to the MSU-200.

Back 152

slave start socket

Front 153

The MSU-200 will not start if the starter temperature is greater than ___ °F.

Back 153

200°F

Front 154

The MSU-200 will automatically shutdown if the feeder tank is less than ___% full.

Back 154

30%

Front 155

The MSU-200 start button must be pressed within ___ seconds after pressing the ON button.

Back 155

120 seconds

Front 156

The MSU-200 needs a ___ minute warm-up period.

Back 156

2 minute warm up period

Front 157

If the MSU-200 oil temperature reaches ___°F before 2 minutes then it is ready to load.

Back 157

140°F

Front 158

Publication for the Fire Fighting vehicle

Back 158

NA 19-25-514

Front 159

Nomenclature for the Fire Fighting Vehicle

Back 159

A/S32P-25

Front 160

The dimension of the A/S32P-25 is _________ inches.

Back 160

64 x 70 x 190 inches

Front 161

The weight of the A/S32P-25 is ____ lbs.

Back 161

18,850lbs

Front 162

The A/S32P-25 has a turbocharged ___ cycle, ___ cylinder, liquid cooled, _____ air induction engine detroit diesel Model 6V-53TA.

Back 162

2 cycle, 6 cylinder, forced air induction

Front 163

The A/S32P-25 develops ___ BHP at ___ rpm.

Back 163

228 BHP at 2800 rpm

Front 164

The A/S32P-25 has a cold weather starting system, and employs a ___ plug to warm each fuel combustion chamber.

Back 164

glow plug

Front 165

The A/S32P-25 engine coolant consists of ___% fresh water and ___% ethylene alcohol.

Back 165

50/50

Front 166

The A/S32P-25 is augmented by ___ Halon 1211 portable bottles.

Back 166

3 bottles

Front 167

Water pump flow rate on the A/S32P-25 is selected manually by a __ to __ joystick pressure control valve.

Back 167

0-500

Front 168

The size of the National Fire Hose Thread Fittings on the A/S32P-25 is ___ inches.

Back 168

2.5 inches

Front 169

The handline of the A/S32P-25 is a ___ inch hose and ___ feet long with nozzle.

Back 169

1.5 inches; 100 feet long

Front 170

The A/S32P-25 has a ___ gallon water tank capacity.

Back 170

750 gallons

Front 171

The charge pump control of the A/S32P-25 operates at a constant hydraulic pressure between ___ to ___ psi.

Back 171

230 to 300 psi

Front 172

Nomenclature of the low loss closed loop liquid oxygen servicing trailer

Back 172

TMU-70/M

Front 173

Publication for TMU-70/M

Back 173

NA 19-25D-26

Front 174

The TMU-70/M has a ___ gallon dewar storage tank.

Back 174

50 gallon

Front 175

The TMU-70/M has a ___ liter dewar transfer tank.

Back 175

15 liter

Front 176

The TMU-70/M is to be used only for _____ and _____ of liquid oxygen.

Back 176

storage and transfer

Front 177

The storage tank working pressure of the TMU-70/M is ___ psig

Back 177

50 psig

Front 178

The transfer tank working pressure of the TMU-70/M is ___ psig

Back 178

90 psig

Front 179

Liquid oxygen boils at ____°C

Back 179

-183°C

Front 180

Nomenclature for Aircraft Towing Tractor

Back 180

A/S32A-31

Front 181

Publication for A/S32A-31

Back 181

Na 19-40-521

Front 182

Tires of the A/S32A-31 are set to ___ psi.

Back 182

60 psi

Front 183

What is the nomenclature of the Static Frequency Converter?

Back 183

A/M24M-5

Front 184

Publication of the A/M24M-5

Back 184

NA 19-40-524

Front 185

The A/M24M-5 converts ____ VAC __ phase __ Hz to ___ VAC ___ phase ___ Hz, ___ VDC and __ VDC

Back 185

440/220 VAC 3 phase 60 Hz to 115 VAC 3 phase 400 Hz, 270 VDC and 28 VDC

Front 186

The drawbar pull of the A/S32A-48 is ___ lbs

Back 186

35,000 lbs

Front 187

Maximum towing capacity of the A/S32A-48 is ___ lbs

Back 187

350,000 lbs

Front 188

Max and minimum forward and reverse speed of the A/S32A-48 are ___ and ___ mph

Back 188

17 and 7 mph

Front 189

The idle speed of the A/S32A-48 is ___ rpm

Back 189

850rpm

Front 190

The total engine system fluid capacity of the A/S32A-48 is ___ qts

Back 190

13.7 quarts

Front 191

The NC-10 provides ___ KVA at ___ PF ___ volts ___ phase ___ Hz alternating current at ____ rpm

Back 191

90 KVA 0.8 PF 115/200 volts 3 phase 400 Hz at 1846 rpm

Front 192

The NC-10 has a ___ gallon fuel tank capacity

Back 192

30 gallon

Front 193

The NC-10 limits speed to ___ at no load.

Back 193

2200

Front 194

The A/M32A-108 limits engine speed to ___ max

Back 194

2210 max

Front 195

The engine overspeed switch shuts down engine when speed exceeds ______ rpm

Back 195

2150 +/- 50 rpm