CHAPTER- 5 ANALYSIS OF STEEL LEAF SPRING ________________________________________________________________ The aim of this analysis is to study the multi-leaf steel leaf spring under loading conditions and verify those results within the allowable limits. ANSYS software is used to analyze the stresses and strains by performing static analysis for the given leaf spring specifications and modal analysis is performed to determine the natural frequencies and mode shapes to asses the behavior of the…
CHAPTER 5 EXPERIMENTATION 5.1 Spur gear terms and concept Fig. 5.1 Terminology definitions for spur gears The radial distance from the pitch circle to the outside diameter is called as addendum. The radial distance between the pitch circle and the root diameter is called as dedendum. The distance of the arc along the pitch circle from one side of a gear tooth to the other is called as circular thickness. The length of the arc of the pitch circle from one point on a tooth to the same…
Particle Deformation and Fragmentation: As compaction force increases, contact area between particles increases, particle deformation starts to occur. Elastic deformation: granules attempt to return to their original shape or form after stress is released. Plastic deformation: granules do not totally recover after stress is released. Fragmentation occurs when compaction force continues to increase Particles fracture, create multiple new surface sites, additional contact points and potential…
strength or intensity is the force which maintains the magnetic flux and produces a particular value of the flux density B at that point in a magnetic field. Therefore the flux density is the cause while the flux density (B) is the effect. The flux density can be assumed proportionally to the field intensity in a magnetic field which comes in three parts. First part is: Where U stands for the permeability of force (the measure of the degree to which the magnetic line of force can penetrate…
Model descriptions SWAN model The SWAN model [12,18] is based on the spectral action balance equation rather than the spectral energy balance equation. The evolution of the action density N is governed by Komen et al. [13]: ∂N/∂t+∇_x ⃗ ∙[((c_g ) ⃗+U ⃗ )N]+(∂c_θ N)/∂θ+(∂c_σ N)/∂σ=S_tot/σ where, N(σ.θ) is the action density spectrum, x is space, t is time,θ is wave direction, σ is relative frequency, S_tot is the source term total, and c_g represents the propagation velocity. The first term in the…
Bending Strength requirement This is the first body requirement and its task is to support all the vehicle subsystems. The body in static is going to suffer bending due to the weight of the components, passengers, fuel and cargo, Figure 42. Similar to a beam simple supported, the very first requirement is that the structure bend sufficient to absorb the energy due to the weight, but has to withstand the weight under different loading scenarios. Figure 42: Body loading under a static scenario…
dimensions are 10 mm × 10 mm × 55 mm and V- notch made at angle of 45° with a depth of 2 mm then the experiment was done and values were tabulated. 3.3 SHORE DUROMETER HARDNESS STRENGTH Hardness was defined as materials resisting property to prevent permanent indentation. Durometer is a measure of hardness in polymers, fibre and rubbers where it measures the indentation depth in the material. According to ASTM D2240 tests were conducted on specimen using Durometer in the room temperature [5].…
The most prominent motif in Shakespeare's Romeo and Juliet is the motif of light and dark. In this famous tragedy, beauty is often associated with light. Before Romeo meets Juliet his world is described as dark, gloomy and depressed, after he meets her, however, it is evident that Juliet brings him light. Essentially, Juliet is the healer of Romeo’s depression. The motif of light and dark in the Tragedy of Romeo and Juliet is shown to change over the course of five acts. The beginning of…
1. Derive the mathematical expression for the Lorentz transformation equation. relative orientation of the co-ordinate systems indicated in fig.2 A light-signal, which is proceeding along the positive axis of x, is transmitted according to the equation : x - ct = 0 _______ (1). Since the same light-signal has to be transmitted relative to K1 with the velocity c, the propagation relative to the system K1 will be represented by the analogous formula x' - ct' = 0 _______(2) therefore:…
three fins. The three wings were placed toward the very back of the rocket, causing the rocket to fly smoother, and creating less drag. Only three wings has been placed on the Twix Kix due to the mass needing to stay low enough for it to overcome the force of gravity. They were cut out of cardboard, and measured precisely so that the rocket does not swerve off course during the launch. The fins of the…