Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
298 Cards in this Set
- Front
- Back
- 3rd side (hint)
|
which squadrons form the MXG? |
Maintenance Operation sq, Maintenance sq, AC Maintenance sq, & QA |
001 |
|
|
Who does QA directly work for? |
MXG Commander |
|
|
|
how does QA identify negative trends and problem areas? |
Through evaluation and/or inspection |
|
|
|
The maintenance operations sq is directly responsible to the MXG commander for a variety of tasks in order to support the group production effort? Which tasks are these? |
Administration, analysis, training management, and programs and resources |
|
|
|
What are main functions of the MOC? |
Monitor and coordinate sortie production, maintenance production, and execution of flying and maintenance schedules, and maintain visibility of fleet health indicators |
|
|
|
In order for the MOC to comply with requirements and to identify potential problems, what type of exchange is crucial? |
Detailed info |
|
|
|
Which two squadrons may the maintenance sq be divided into? |
CMS and EMS |
|
|
|
If you are assigned to the MXS or CMS/EMS, to which flights might you be attached? |
Propulsion and maintenance flight |
|
|
|
What does the type of tasks does the propulsion flight perform? |
Maintain AC engines, propellers, and their components; engine/modular/propeller/ accessory assembly, disassembly, test, and repair |
|
|
|
If you are assigned to a specialist flight in the AMXS, which engine tasks would you be required to accomplish? |
Trouble shooting w fine malfunctions, component removal and replacement, compressor washes, performing inspections, and servicing |
|
|
|
What is the purpose of the CFETP? |
Provide career field managers, commanders, training managers, supervisors, and the trainers |
002 |
|
|
What does the fourth position of the AFSC 3A652 represent? |
Skill level |
|
|
|
What is your title when you obtain the 5 skill level? |
Journeyman |
|
|
|
What skill level would you posses when you obtain the title of Superintendent |
9 |
|
|
|
How many months must you have in the AF before you may attend Airman Leadership School? |
48 months |
|
|
|
Why should you keep your CDC's after you've completed them? |
You will need to study the material for promotion tests |
|
|
|
When are you promoted to the rank of TSgt, what school must you attend? |
NCOA |
|
|
|
At what skill level is an Airman expected to fill positions such as flight chief or production supervisor? |
9 |
|
|
|
What is the purpose and goal of the AFOSH program? |
To ensure safety |
003 |
|
|
What series of AFOSH standards govern occupational safety? |
91 |
|
|
|
What series of AFOSH standards govern occupational safety?
|
|
|
|
|
Who would you contact if you have questions regarding unsafe conditions? |
Supervisor or unit safety rep |
|
|
|
What is the purpose of safety in the work area? |
To prevent personal injury, save time and money |
|
|
|
How can most hazardous situations be avoided? |
Wearing PPE, following procedures, and asking for help |
|
|
|
Lost four good housekeeping practices: |
Rid of clutter, place oily rags in containers , clean spills asap, and dispose of FOD |
|
|
|
How should you lift a heavy or bulky object? |
Using leg and arm muscles while squatting |
|
|
|
What AFI outlines the responsibility of every position in the chain of command? |
AFI 21-101 |
|
|
|
What AFI outlines the responsibility of every position in the chain of command? |
AFI 21-101 |
|
|
|
On what aspects of performing maintenance must all levels of supervision place emphasis? |
Safety, quality, and timeliness |
|
|
|
What types of maintenance actions are prohibited? |
Shortcuts and incompleteness |
|
|
|
What types of maintenance actions are prohibited? |
Shortcuts and incompleteness |
|
|
|
What does maintenance discipline require of personnel? |
Integrity and compliance |
|
|
|
What types of maintenance actions are prohibited? |
Shortcuts and incompleteness |
|
|
|
What does maintenance discipline require of personnel? |
Integrity and compliance |
|
|
|
What will happen to personnel who fail to uphold maintenance discipline? |
Accountability |
|
|
|
What two things should you check to ensure the aircraft is safe for you to perform maintenance? |
AC forms and personnel onboard and around the aircraft |
004 |
|
|
Which AC forms should you check for entries that may prevent you from starting your assigned task? |
AFTO 781H, aerospace vehicle flight status, maintenance discrepancy and work document, maintenance documents |
|
|
|
Why should you check with other people working inside or outside of the AC prior to starting maintenance? |
They may have changed info on the forms |
|
|
|
Why are interim TCTOs issues in Ann electronic message format? |
To speed delivery and implementation |
|
|
|
How are hard copies of immediate action TCTOs identified? |
"Immediate Action" is printed in red at he top of the first page along with a series of red "X"s along the borders of the first page |
|
|
|
What TCTOs are issues when potentially hazardous safety conditions cloud result in injury to personnel? |
Urgent action |
|
|
|
Wh would a routine TCTO be issues |
For any condition not covered under urgent or immediate |
|
|
|
What are ways, or formats in which TOs are issued? |
By hard copy or compact disk |
|
|
|
Why is it important to ensure you are using the most cuffing TO for your particular job |
Bc working with outdated info could result in serious injury and or damage to tools/ equipment |
|
|
|
What factors are needed for a TO revision |
Impact of changes and supplements on the usability of the TO, urgency of need for update, cost, and quantity of stock at hand |
|
|
|
If a TO change contains new material that cannot be included jean existing page, how are added pages assigned |
The preceding page number and suffix |
|
|
|
How can you tell when the year or a pic in a TO has been changed |
Bold vertical black line alongside the affected text, or pointing hand figure |
|
|
|
What form is used to recommended improvements to TO's |
AFTO IMT form 22 TM change recommendation and replacement |
|
|
|
What are primary factors that create static electricity? |
Motion and different movement |
|
|
|
What are potential results of an approved TO recommendation? |
Connect error, insert omitted fact, and improve procedure |
|
|
|
Paper copies of the AFTO IMT 22 will not be accepted without prior approval from whom |
Supervisor of person submitting |
|
|
|
What is reliability centered maintenance |
Disciplined method to I.d preventative maintenance to ensure equipment meets life expectancy minimum cost to gov |
|
|
|
What is the goal of RCM |
To optimize ETUW |
|
|
|
What are the two classifications of failures |
Potential and functional |
|
|
|
What is the process of trying to match modules with approx the same amount of time left on them when assembling engines |
Module matching |
|
|
|
What is the ET&D program |
Integration of hw, sw, maintenance, and diagnostic process to quantify and monitor engine health |
|
|
|
List the purposes of ET&D |
Predict, detect, conduct, diagnostic process to ensure equipment forecast time and material requirement to minimum ENMCS status |
|
|
|
What is the primary goal of the ET&D program |
Reduce shop slowness and increase spare engine levels |
|
|
|
How do flight line personal use ET&D |
Reduce flight cycle costs and improve reliability |
|
|
|
What is effective grounding? |
Consists of providing a path for static electricity to flow to a grounding point in the earth |
|
|
|
How do depot and product center engineers and technicians use the ET&D |
Increase average ETOW and eliminating time based removals |
|
|
|
What is the ET&D used to determine |
If maintenance must be performed before next flight and or scheduled TC |
|
|
|
What are CFRa designed for and what type of support do they provide |
To take advantage of existing repair centers to sustain deployed forces |
|
|
|
What does the centralized rotatable pool CPR provide |
Sufficient #'s of spare asserts to meet timely placement of serviceable assets where needed |
|
|
|
Operating CRP rules should be mutually agreed upon by whom |
Lead commanders |
|
|
|
How are CIRF assets accounted for and tracked |
AF portal |
|
|
|
What is depot maintenance |
Maintenance on material in need of overhauling part, assemblies, and conditions |
|
|
|
Why does depot maintenance stock serviceable equipment |
More extensive repair facilities |
|
|
|
What type of maintenance does depot perform |
Engine overhaul, JEIM, disassembly, inspection, repairs, replacement, assemble, and tests |
|
|
|
From where does the AF obtain depot maintenance |
Organic department of deference facilities and prior sec contrtuctio s |
|
|
|
What is the purpose of bonding? |
To eliminate differentials in electrical changes that exist, or are grounded between a component and AC or 2 components |
|
|
|
List the most common forms of depot level assistance |
Depot field and contract field teams |
|
|
|
What is the primary objective of the CEMS |
Obtain info or status, conditioning and location of engine, gearboxes, and modules |
|
|
|
What is used to collect and store info provided by different engine reporting system |
CEMS collects info and stores in central database |
|
|
|
What are the primary objectives of the reporting engine system |
Maintain accurate and timely inventory |
|
|
|
What section monitors engine removals and replacements and tracks components at base level |
Base level management section |
|
|
|
What are some functions of CEMS |
Provide readiness through collection of info that indicates view of op capability |
|
|
|
What are the two categories of status reporting |
Engines and modules and tracked components |
|
|
|
What is the purpose of AFTO IMT 95 |
Maintain history of significant maintenance actions on and items of equipment |
|
|
|
What should you do if an automated data system is not available for engine status reporting |
AFTO IMT 95 |
|
|
|
What conditions should be documented on the AFTO IMT 95 |
Condition that have bearing on future maintenance |
|
|
|
At the locations where a bonding wire is attached, what surface requirements must be met? |
Clean and unpainted |
|
|
|
What is the purpose of the lead the fleet program |
To track stress of engine and sub systems |
|
|
|
What is the lead the fleet program |
An accelerated mission usage program |
|
|
|
What type of info does the lead the fleet provide |
Early Intel in equipment reliability, integrity, and maintain ability |
|
|
|
List lead the fleet objectives |
Accelerate pacer items ahead of operational fleet, update scheduled maintenance, advance item max life, provide analysis of trending data, i.d hw service life deficiencies, detect unique durability problems, evaluate engine controls, provide lead time for solving maintenance issues |
|
|
|
How do participating units manage pacer engines |
Accelerate pacer engines at twice the rate of normal flying until items are 2 years ahead of fleet engines |
|
|
|
Which program does the lead the fleet support |
Overall engine life cycle management plan |
|
|
|
Why shouldn't you use a greasy tool |
Slippery and loose grip |
|
|
|
Why shouldn't you put tools in your pockets |
Increases chances of loss |
|
|
|
At what times should your toolbox be inspected |
Start and end of each shift, and when leaving the area |
|
|
|
What should you check for when inspecting your toolbox at the beginning of each shift or before leaving the tool crib section |
Missing damaged corroded and dirt tools or FOD |
|
|
|
What should you do if the clothing you are wearing becomes soaked with fuel? |
Remove clothing in safe area and shower |
|
|
|
What should you do with your toolbox when it is not in use and why |
Lock and secure it to lessen chances of losing items |
|
|
|
What can you use when your toolbox can't be located within arms reach |
Toolbag |
|
|
|
How is the torque value of a torque wrench expressed |
Inch pound and foot |
|
|
|
What is the most common type of torque wrench used in the AF |
Breakaway |
|
|
|
How do you reduce torque setting on a torque wrench |
Turn the handle clockwise |
|
|
|
If you drop a torque W wrench what action must you take |
Recalibrate |
|
|
|
You're torquing a castellated nut. The mmmm torque value is 50 inch pings and the max torque values 60 inch pounds the slot in the castellated but can't be aligned with the locking hole in the bolt corrective action should you take |
Replace bolt or nut |
|
|
|
In the following durations use the given information to determine the desired torque their then information provided you wish to exert 200 inch pounds at the end of a extension the length of the handle is 12 inches and the extension is 8 inches what should be the desired torque handle setting |
12 inch pounds |
|
|
|
For what purpose should you use a thickness gauge |
Measurement between 2 surfaces |
|
|
|
When using the thickness gauges to check the gap between two surfaces what important point regarding accuracy should you always remember |
Accurate of gauge depends on pressure or tension recognition |
|
|
|
What conditions could result from excessive inhalation of fuel or chemicals? |
Dizziness, headaches, unconscious, and loss of muscular coordination |
|
|
|
What are the parts of an outside micrometer |
Frame anvil spindle lock vernier scale barrel and thimble |
|
|
|
What are the three basic types of micrometers and their purpose |
Outside- measure out Depth -measure forth Inside - measure inside |
|
|
|
What is the longest calibrated movement possible between then spindle and the anvil of a 6 inch outside micrometer and what is the movement called |
1 inch |
|
|
|
List four of the precautions too while take when using s micrometer |
Do not close too tightly never swung by thimble do not handle roughly and always told frame stationery |
|
|
|
Which other measurement tool can you use while practicing with a micrometer in becoming proficient in using the micrometer |
Feeler gauge |
|
|
|
How many revolutions would you have to turn the thimble of a micrometer to read 0.025 inch |
One |
|
|
|
Which part of the micrometer has graduations that represent tenths of an inch |
Barrel |
|
|
|
What measure does the vernier scale on the micrometer provide |
Accurate to ten thousands of an inch |
|
|
|
What type of device is a dial indicator |
Mechanical motion amplifying device |
|
|
|
Which two indicators within one dial face one dial indicators, what does the smaller under indicator measure |
Revolutions |
|
|
|
When May a safety net be used? |
When Above 25 ft |
|
|
|
Which control switch in the kne 8025 A multimeter is used to set the Meyer to check for altering current direct Current and ohms |
Function selector rotary switch |
|
|
|
Which control switch is here to take measurements in a circuit that's difficult to reach |
Hold push button |
|
|
|
On what side of the circuit js the black test lead connected |
Negative side |
|
|
|
Where are measurement results displayed on the meter |
Digital display |
|
|
|
What do the letter OL Indicate |
Input over the meter is over the range being used |
|
|
|
What's the most important safety precaution to observe when using the ohms function of the multimeter |
Do not hook to live circuit |
|
|
|
How is the multimeter connected to a component that's to be measured |
Black lead to negative Red lead to positive |
|
|
|
When using a multimeter what safety precautions must be followed |
Inspect avoid working alone and use one hand |
|
|
|
What is the max voltage that can be measured or the decimal point is at 300 on the digital display |
320 volts |
|
|
|
What is the purpose of the borescope inspection |
To perform visual internal inspection |
|
|
|
Why should AF personnel be so concerned about FOD? |
Loss f resources |
005 |
|
|
What are some limitations of the borescope |
Access parts, serviceability, and experience |
|
|
|
What types of borescopes are used on today's engines |
Rigid flexible and video image |
|
|
|
The rigid and flexible borescopes are similar except what |
Rigid doesn't have angulation lever |
|
|
|
What types of view are available with the distal tip of the rigid borescope |
Direct or lateral |
|
|
|
What factors determine whether or not someone is capable of being qualified for borescope operation |
Experience maturity and rank |
|
|
|
What type of damage results from a pinched fiber bundle or light guide cable |
Damaged fiber |
|
|
|
Where are bolt markings located |
the bolt head |
|
|
|
Where is the diameter of a bolt measured |
Grio |
|
|
|
What are fine thread bolts stronger than coarse thread |
Greater cores |
|
|
|
In what two general groups are nuts divided |
Non self lock and self lock |
|
|
|
What can happen when loose objects are blown or washed i Onto the runway? |
Engine intake will suck them in |
|
|
|
What is the maximum safe working temperature of non metallic self locking nuts |
250 Fahrenheit |
|
|
|
Which screw is made from high stencil material |
Structural |
|
|
|
Which screw is used for general purposes |
Fillister |
|
|
|
What are four types of machine head screws |
Roundhead flathead fillister socket head |
|
|
|
How do washers secure bolts and screws |
Spring action and sharp tempered edge |
|
|
|
In AC maintenance what are the most commonly used pins |
Tapered pins, flathead, cotter, roll, and quick release |
|
|
|
What type of pin is used in joints what Carry shear loads and where the absence of clearance is essential |
Tapered pins |
|
|
|
What type of pins is used in conjunction with cotter or safety pin |
Flathead |
|
|
|
How many times may you reuse a cotter pin |
Never |
|
|
|
What is the purpose of safe safetying devices |
To ensure torque is maintained |
|
|
|
Who is assigned as the FOD prevention program manager? |
Vice wing commander |
|
|
|
What form is documented to identify an armed AC |
AFTO 781 H |
|
|
|
When lock wiring two bolts together between what positions should the wire twist begin on the first bolt |
3 & 6 o'clock |
|
|
|
How many twists should be left on the braid when cutting off excess wire |
8-10 |
|
|
|
What advantage does steel tubing have over aluminum |
Withstands rough handling and high pressure |
|
|
|
Why are flexible hose assemblies used instead of metal tubing in some applications |
Carry fluids |
|
|
|
Why should the bend radii on hoses be bent as large as possible |
Avoid kinking the line |
|
|
|
What is used to I.d the hose and tubing system after installation |
Close coded bonds |
|
|
|
What size fitting should be used for a piece of tubing that is 5/8 inch |
10 |
|
|
|
What types of connectors can be used in any system no matter what the pressure is |
Flared sleeve and swags |
|
|
|
What causes most nicks and scratches on engine plumbing |
Careless handling of tools |
|
|
|
How should dust caps be installed on open lines |
Over tube ends |
|
|
|
Who is responsible for preventing FOD by looking for and removing hazards that could cause damage to equipment or loss of life? |
Everyone |
|
|
|
What is the allowable limit for a dent in a straight line |
Less than 20% |
|
|
|
What is a max distance w hose can go w max support |
24 inches |
|
|
|
What is the purpose of leaving 11/2 inches of slack in a hose that conveys to an engine component |
Prevents hoses being pulled off |
|
|
|
When an engine is sent to the engine shop with a known discrepancy what should you do before you being corrosive action |
Review AC and engine forms |
|
|
|
Why is it important to have a clean container to catch oil when checking the main oil filter for contamination |
To avoid false contaminations |
|
|
|
Why should a prelim inspection of the engine be performed prior to correcting a known discrepancy |
So no unknown discrepancies slip by |
|
|
|
What are possible consequences of a dirty work area |
Contamination and subsequent engine failure |
|
|
|
How are hints on maintenance procedures highlighted in maintenance manuals |
In the form of warnings and cautions |
|
|
|
Why should you never stack engine parts with precision finishes on concrete floors |
It may lead to knicking and marring that would lead to cracks in metal and leaks in exhaust gasses during engine operations |
|
|
|
Before you prepare an engine for air shipment, what precaution do you take for engine fuel and oil systems |
Seal all drain openings, open lines, and fittings Use caps to seal make and female flared type fittings Use O ring seal plugs to seal stand screw thread openings Torque all plugs and caps |
|
|
|
What must all workers account for at the start and end of each shift and action? |
Tools |
|
|
|
What precaution should be taken during aid shipment of engines attached to trailers, trucks, stands, or in containers |
Torque all bolts cap screens and nuts Secure w locking device Check tires condition and inflation |
|
|
|
What is the most common type of shipping container for components |
Cardboard box |
|
|
|
A flexible environmental container can be used for what type of shipment |
Air and surface |
|
|
|
What type of cover can be opened by using a zipper |
Prefabricated |
|
|
|
Which Manila covers reporting an engine that was improperly shipped |
AF MAN 24-204 |
|
|
|
What types of inspections are performed on engines after they are involved in mishaps or are dropped |
Visual |
|
|
|
If an engine was dropped en route and an inspection revealed only minor damage to the engine which level of maintenance would be performed |
Intermediate maintenance |
|
|
|
How is dehydration accomplished in a metal shipping container |
Placing pre determined amount of bagged dehydration agent in baskets with pressurizing nitrogen |
|
|
|
How does the flexible environmental container differ from metal containers |
They do not provide mechanical and physical protection |
|
|
|
Empty storing and shipping containers should be pressurized to what pressure |
5+/-1 pounds per sq inch |
|
|
|
What should you do when you suspect that an item is lost on an AC, and it is an area where it can cause damage? |
Red X on AC |
|
|
|
What warming is found on all engine and module storage and shipping containers |
Release pressure before opening container |
|
|
|
Where is the filler valve located |
Front end of the container |
|
|
|
What could happen if you remove the lid from a storage and shipping container without releasing internal pressure |
Damage to the container and yourself and your workers |
|
|
|
What direction are the turn lock fasteners turned when removing the lid |
Counter clockwise |
|
|
|
After the lid is removed from the container where should it be placed |
On wooden blocks |
|
|
|
Which end of the engine is placed over the front of the container |
The aft end |
|
|
|
What is the purpose of the wire basket located in the bottom half of a shipping container particularly important |
Both halves are a match set and must be kept together |
|
|
|
What markings are used on shipping containers |
Status of item and date of inspection and activity |
|
|
|
What must you do before loosening the adjusting screws |
Release all pressure from the container |
|
|
|
What secures an F100 core modules front and rear adapters to the container support |
4 pins |
|
|
|
What should you wear when entering the intake or exhaust? |
Bunny suit |
|
|
|
What preservation treatment is required for engines that will not be operated for 48 hours |
Corrosion preventative |
|
|
|
What fluid is used to preserve oil system for extended periods of engine idleness |
Normal engine oil |
|
|
|
What type of fluid is used in the preservation of the fuel system |
MIL L 6081 grade 1010 |
|
|
|
What is the general engine depreservation procedure |
Service the oil reservoir with lubricating oil |
|
|
|
What are the depreservation steps for fuel |
Flush system w fuel Rotate engine rotor and energize main fuel system Drain fuel filter And clean them |
|
|
|
What are the two types of corrosion |
Direct chemical attack by corrosive liquid and gases Electromechanical action in which the metal being corroded becomes part of an electrolytic cell |
|
|
|
Where does chemicals corrosion start |
On the surface where metal is exposed to the environment |
|
|
|
What is the corrosion product of iron alloys |
Red iron rust |
|
|
|
What is electromechanical corrosion |
It's when dissimilar metals are connected by an electrolyte such as water |
|
|
|
What are two basic methods of corrosion prevention |
An oil like protective coating using desiccants |
|
|
|
To whom should you report damaged paving in the AC parking areas and taxiways for immediate repair? |
Base airfield manager |
|
|
|
What TO gives procedures for cleaning a jet engine |
TO 2J 1 13 |
|
|
|
How are internal salt deposits removed from engines |
Using fine spray of water directed into the inlet duct and compressor sections |
|
|
|
What is the purpose of maintenance stands |
To provide working platforms at varying heights |
|
|
|
What are the normal parts of a stand |
Base assembly hydraulic system and platform |
|
|
|
What is the purpose of sweaty pins that are installed in the platforms |
To prevent the stand from lowering while it is in use |
|
|
|
What are the five commonly used platforms |
C1 B1 B2 B4 and B5 |
|
|
|
Which of the maintenance platforms is nonadjustable |
C1 |
|
|
|
What prevents movement of the B4 stand while in use |
Wheels have brakes that lock at 90• |
|
|
|
What is the height range for each platform |
C1: 4ft B1: 7 to 10 ft B2: 13 to 20ft B4: 3 to 7ft B5: 7 to 12 ft |
|
|
|
What is the purpose of the AFTO form 244 |
Provides a means to document equipment delayed discrepancies and corrective actions , record services, periodic and special inspection status, and historical data |
|
|
|
In what two categories are hazardous materials divided? |
Health and physical |
006 |
|
|
What is the purpose of the AFTO form 245 |
Documents discrepancies and corrective actions |
|
|
|
What is the purpose of the hazed communications program? |
Establishing guidance on training employees health safety |
|
|
|
Toxic materials are divided into what three general physical classifications? |
Solids, liquids, and gases/vapors |
|
|
|
What type of gas are we frequently exposed to on the flight line and test cell ops? |
Carbon monoxide |
|
|
|
Which physical form of hazardous material enters the body and can cause rapid toxic reactions? |
Gaseous forms |
|
|
|
What are three types of equipment that produce radio frequency radiation? |
Radio, low frequency radio transmitter, and countermeasure device |
|
|
|
What is the key factor in making PPE program successful? |
Acceptance |
007 |
|
|
What is a critical factor in PPE maintenance? |
Inspection of PPE before and after use |
|
|
|
What is normally used to clean most PPE? |
Soap and water |
|
|
|
When you store PPE, what are you protecting it from? |
Sunlight, excessive heat and cold, and moisture |
|
|
|
What should the design of a storage area allow for? |
Inspection of each container |
|
|
|
When removing spilled or leaking hazardous materials from the storage area, what should you never do? |
Mix incompatible materials/ wastw |
|
|
|
What info must hazard warning labels include? |
I.d of chemicals and appropriate warnings |
|
|
|
For stationary hazard containers, what can be used in place of a label? |
A placard |
|
|
|
An MSDS is cross referenced to every type of material recorded on what document? |
Hazardous chemical inventory |
|
|
|
Where can you find the proper procedures for disposing hazardous waste material? |
MSDS |
|
|
|
What are the primary danger areas that exist around an operating engine? |
Propellers and engine intake |
|
|
|
What are the ways hazardous waste can be disposed of properly? |
Incineration, contracting, and land disposal |
|
|
|
What is the purpose of the maintenance supply system? |
To procure, stock, and issue millions of items to thousands of customers |
|
|
|
What areas of major weapons systems do GLSC's manage? |
AC, engine, communications, test stands, aerospace ground equipments and vehicles, and pads |
|
|
|
What manual prescribes standardized procedures for supplies by AF organizations? |
AF MAN 23-110 |
|
|
|
What are the four primary points of contact within base supply? |
Customer service, retail sales, demand processing, and equipment management |
|
|
|
What is the common term for repair cycle assets? |
DIFM |
|
|
|
What base supply function manages the repair cycle system? |
Repair cycle support system |
|
|
|
What is the purpose of the RCSS? |
To established a firm control over repair cycle assets |
|
|
|
When does the repair cycle time of an item start and stop? |
Starts at the removal from the engine and when demand is made at base supply; stops when returned to base supply |
|
|
|
When you route a part to be repaired through the RCSS which part of the AFTO form 350 do they need? |
Bottom portion, part 2 |
|
|
|
When a propeller is running, what are it's two most dangerous areas? |
Plane and axis of rotation |
|
|
|
What types of items generally require complete depot level overhaul? |
Time change items, items involved in a weapons system accident, items having evidence of contamination, items whose condition can't be determined |
|
|
|
List four of the important supply documents that you may utilize |
Daily document register (D04) Priority monitor report (D18) Repair cycle asset management listing (D23) Due out validation listing (M30) |
|
|
|
Which supply document provides a means for organizations to review all documents numbers processed during the day at the SBSS? |
Daily document register (D04) |
|
|
|
Which supply document provides data by which to monitor due ours and their corresponding status? |
Priority monitor report (D18) |
|
|
|
Why must base supply have a priority system in place? |
Bc they deliver numerous parts to numerous organizations on a daily basis and each mission is different |
|
|
|
What two priority systems does base supply use? |
Delivery priority system and uniform material movement and issue priority system (UMMIPS) |
|
|
|
What two factors determine the priority for an off base requisition? |
Urgency justification code and force activity designator |
|
|
|
What factor is adversely affected by the misuse of priority designators? |
Integrity of the supply system |
|
|
|
What is part 1 of the AFTO Form 350 known as and what is it used for? |
Repair cycle processing tag; attached to items determined to be repaired and forwarded to other activities for repaie |
|
|
|
Where is part 2 of the AFTO form 350 located and what purpose does it serve? |
Section below the perforation; production scheduling document |
|
|
|
What causes the danger area in front of the intake of an operating engine? |
Suction |
|
|
|
Where can you find a block by block explanation of how to document the AFTO form 350 tag? |
TO 00-20-2 |
|
|
|
When an item is sent to the RPC, which blocks are required to be completed by the originator of the 350 tag? |
1 through 14, 15A, and 29 |
|
|
|
When an item is not sent to the RPC |
Blocks 16,17, and 18 |
|
|
|
Where can you go to find detailed info concerning he AF IMT 2005 codes and entries? |
AF MAN 23-110 |
|
|
|
When are you required to enter the type, model, series, and serial number on the AFT IMT 2005? |
When a requirement is for an MCS or PMCS reportable item |
|
|
|
Which form should you submit if it's determined that a first time request part will become a recurring one and the stock level needs to be adjusted? |
AF IMT 1996 Adjusted stock level |
|
|
|
Where can you look to find info concerning how to use the condition tags and the required entries for each? |
TO 00-20-3 |
|
|
|
What conditions warrant use of the DD form 1575, suspended tag? |
When the part is awaiting maintenance or parts |
|
|
|
What is the purpose of the DD form 1577? |
To identify an unserviceable item |
|
|
|
What is the purpose of DD form 1577-2? |
I.d defected but repairable items |
|
|
|
What is the minimum safe distance that should be established to avoid the effects of an exhaust blast? |
200 fewt |
|
|
|
What is the definition of a shelf life item? |
An item that posses deteriorative characteristics o the degree that storage time must be assigned to ensure the item will p satisfactorily |
|
|
|
What is the main difference between types 1 and 2 shelf life items? |
Type1: definite non extendible shelf life Type2: not extendable |
|
|
|
How is the info on DR's used |
To increase op capability by correcting defects in design, material, quality, or maintenance of equipment and to reflect last performance |
|
|
|
You receive a part from supply that does not fit correctly and the part is still under warranty. How does the change the DR process? |
It doesn't |
|
|
|
What are some of the justifications for initiating a DR? |
Safety; does not fit/ work ion receipt, fails before expected life cycle |
|
|
|
If you find a deficiency, that if Uncorrected would cause injury, which category submit the DR? |
Category 1 |
|
|
|
Within what timeframe must all category 2 DR' be forwarded |
3 work days |
|
|
|
List some examples of equipment authorization inventory data items |
Individual equipment, organized equipment, and special projects/ equipment |
|
|
|
EAID items require formal supply accountability must be reflected on what listing |
Custodian authorization/ custody receipt listinf |
|
|
|
Who provides you with the required equipment management training? |
Equipment management |
|
|
|
What is the best way to protect yourself from noise levels that can cause permanent hearing loss? |
Ear plugs and hearing equipment |
|
|
|
List the things you must accomplish if you serve as an equipment custodian |
Ensure you attend regular training; inventory and account for all equipment on current CA/ CRL |
|
|
|
Why are technical orders numbered? |
To provide sequence for filing, categorize by equipment type, and act library |
|
|
|
In the first section of TO number 1F-16C-1 what does the 1 represent |
AC |
|
|
|
I'm the first section of TO number 2J-F110-6-6 what does the J represent |
Jet |
|
|
|
In the TO number 2J-F110-6-14 what does the F110 represent? |
Engine model # |
|
|
|
How are index TO's identified |
Single 0 is first section of TO # |
|
|
|
What can USAF TO catalog database be used for |
Established and requisition TO requirement for maintenance of TO libraries; search for new updates and rescinded TO's |
|
|
|
List three examples of O&M TO |
Flight manual program, work package, and on equipment |
|
|
|
What do methods and procedures TO establish |
Policies, methods and procedures relating to TO system, main management, grand handling of aerospace vehicles m, maintenance practice and safe use of equipment |
|
|
|
What are abbreviated TO's |
Excerpts |
|
|
|
Why should personnel exercise caution when approaching the plane of rotation of a helicopters main rotor blades? |
Rotors droop at decreased speeds |
|
|
|
TCTOs are authorized method for doing whag |
Directing and providing instructions for modifying military systems |
|
|
|
Which technical manuals generally describe the overall AC and it's installed systems and subsystems? |
General equipment manuals |
|
|
|
What type of info do GA manuals provide? |
Detailed system and subsystem description |
|
|
|
What type of info do JG manuals provide? |
Detailed start to finish, step by step |
|
|
|
Which type of TM contains operational fault identification procedures and reporting instructions that allow the flight crew to describe the conditions pertaining to a malfunction? |
Fault reporting Manual |
|
|
|
Describe the process of troubleshooting equipment when using an FI manual |
The parts of a system tears in a logical sequence until a specific line replaceable unit fail is found |
|
|
|
Which type of manual illustrates, lists, and describes all part, modules, and special support equipment necessary to maintain AC engines? |
Illustrated parts breakdown |
|
|
|
If you me to look up a party number, which two sections of the illustrated parts breakdown manual could you use |
Group assembly parts list and numerical index |
|
|
|
How are TCTO instructions used? |
Mortifying military plays tens with specified time limits |
|
|
|
How can a TCTO be quickly identified |
By #5 or higher in third section |
|
|
|
When approaching or leaving a helicopter with blades rotating, what two things should personnel remember? |
Stay in pilots view and crouch |
|
