Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
120 Cards in this Set
- Front
- Back
What are the Air Force core values?
|
Integrity, service before self, and excellence
|
|
Careerism and self-interest can do the most damage when displayed by the
|
leader
|
|
When people are taught the right way to do something, they're being taught the
|
safe way
|
|
How should you treat safety, when its integrated into your job training
|
As a separate item from training
|
|
If you see people who outrank you walking around with tools in their pockets or using equipment improperly, you should
|
alert them to the potential hazards
|
|
A major cause of accidents is
|
horseplay
|
|
Which item may be worn when performing maintenance on electrical equipment or aircraft electrical systems?
|
plastic rim glasses
|
|
If the load is to heavy or bulky for two people to carry safely, what should you do
|
Use a hand truck or forklift
|
|
Which is not a sign of fuel vapor inhalation?
|
Emotional irritability
|
|
When using comppressed air for cleaning, use s diffuser nozzle and make sure the pressure does not exceed how many pound per square inch (psi)
|
30
|
|
You use compressed air to clean clothing when
|
it is not on the body
|
|
when are the grounding procedures for the hand-operated hydraulic servicing cart during servicing operations
|
Do not need to ground
|
|
During engine runup, all unnecessary personnel and equipment will be kept clear at least what distance from the rotary wing aircraft
|
A distance equal to its length
|
|
Exercise caution when approaching the plane of rotation of the main rotor blades, especially during engine runup and shut down, because the rotor blades tend to
|
droop at decreased speeds
|
|
Radiation hazards vary based on the
|
strength of emission and time of exposure
|
|
What is normally a safe distance to the front and side of the intake duct when a jet engine is operating
|
25 feet
|
|
Which object would cause an aircraft to be considered "explosives-loaded"?
|
Flares
|
|
what precaution must be observed before moving a explosives-loaded aircraft into a hangar?
|
Remove all ammunition and explosives
|
|
The proper postioning of fire extinguishers is determined by
|
distance criteria
|
|
When possible, from where should you fight a fire?
|
the upwind side
|
|
A fire occurring in paints, cooking oil, grease, and petroleum products is a class
|
B
|
|
A fire occuring in electrical equipment is a class
|
C
|
|
A fire occuring in combustible metals such a magnesium, potassium, zinc sodium, and etc, is a
|
D
|
|
Which type of auxilary publication augments directive-type publications issued by higher headquaters
|
Supplement
|
|
Which visual aid gives examples of international aircraft marshalling signals
|
AFVA 11-224 International Aircraft Marshalling Signal
|
|
Which publication contains official and professional information on matters related to defense policies and programs of interest?
|
Staff digests
|
|
which type of technical order (TO)files normally are established and maintained by Air force bases and activities
|
Limited
|
|
Technical orders (TO) are filed and updated in accordance with
|
TO 00-5-1-WA-1, AF Technical Order System
|
|
In general technical order (TO), which part of the number identifies an individual TO?
|
Third
|
|
Which technical order (TO) establishes functional-check-flight requirement for the HH-60G helicopter
|
1H-1(H)G-6
|
|
which technical order (TO) gives istructions for time compliance technical orders (TCTO)?
|
TO 00-5-15-WA-1, Air Force Time Compliance Technical Order System
|
|
An urgent action time compliance technical order (TCTO) must be completed within one to
|
10 days
|
|
What time compliance technical orer (TCTO) is issued for deficiency that constitutes a hazard through prolonged continued usage?
|
Routine action
|
|
Which device or publication enables you toi accomplish scheduled inspections on aircraft efficiently?
|
Inspection workcards
|
|
How soon should you submit a technical order (TO) deficiency report if you discover an error in the TO that involves flight safety that would result in serious injury
|
Immediately
|
|
Which level of maintenance perform off-equipment maintenance for direct support of using organization
|
Intermediate
|
|
Who uses the Maintenance Information System (MIS) to identify and track Repeat/Recur discrepancy trends, and documents the discrepancies accordingly on the Air Force Technical Order (AFTO) Form?IMT 781A, after an aircraft flight is completed
|
Aircrew and Maintenance Debrief Section
|
|
What must units develop to insure crashed, damaged, or disaled aircraft recovery (CDDAR) coverage after duty hours?
|
Emergency recall or mobilization rosters
|
|
Who appoints the crashed, damaged, or disabled aircraft recovery (CDDAR) Team Chief?
|
Maintenance Group Commander (MXG/CC)
|
|
During the fix phase of an aircraft inspection, besides performing maintenance found during the look phase, what other maintenance is performed?
|
Preplanned maintenance
|
|
Who establishes the requirements for the development of 3-level, career development course (CDC), and exportable training courses?
|
The career field
|
|
Which individual or activity determines the inspection method used to inspect aircraft?
|
Local or major command (MAJCOM)
|
|
How many authorized inspection concepts are used by Air Force?
|
Five
|
|
When an H-60 is scheduled to fly after being idle for 48 hours, what type of inspection should you perform?
|
Pre-flight
|
|
When an aircraft lands following the last flight of a flying period what type of inspection should you perform?
|
Basic Post-flight
|
|
What type of inspection is performed when a newly assigned aircraft arrives on station?
|
Acceptance
|
|
Which form is the source document for logging flight activity for individuals
|
Air Force technical order (AFTO) Form 781, AFORMS (Air Force Operations Resource Management System) Aircrew/Mission Flight Data Document
|
|
Which form is used to record aircraft time, engine data, and includes operating times?
|
AFTO Form 781J, Aerospace Vehicle-Engine (operating time, cycle, and oil added) Flight Document
|
|
Who is responsible for maintaining the binder of Air Force Technical Order (AFTO) 781- series forms?
|
Crew Chief
|
|
The technical orders (TO) that authorize the use of abbreviations for use in Air Force Technical Order (AFTO) 781-series form are listed in
|
TO 00-20-1-WA-1, Aerospace Equipment Maintenance Inspection, Documentation, Policies and Procedures
|
|
which symbol represents an unknown condition and a more serious condition may exist?
|
Red dash
|
|
Which Air Force form is used to show physical presence or absence of -21 equipment?
|
AF Form 2691, Aircraft/Missle Equipment Property Record
|
|
Which Air Force Technical Order (AFTO) form serves as a permanent history of significant actions for an aircraft?
|
AFTO Form 95, Significant Historical Data
|
|
The maintenance data documentation (MDD) system provides a mechanism for
|
collecting, storing, and retrieving base-level data
|
|
Which is not an intended user for maintenance data documention (MDD) data?
|
Worldwide Data Collection Center (WDCC)
|
|
Individual Intergrated Maintenance Data System (IMDS) identification (ID) passwords should be changed whenever compromise is suspected or not more than every
|
60 days
|
|
Critical items are generally small numbers of items that cause the largest number of
|
not mission capable supply (NMCS) conditions
|
|
Critical items may be designated by local chief
|
of supply
|
|
Which expendability, recoverability, reparability codes (ERRC) are considered repair asset codes
|
XD or XF
|
|
Which form is used for internal control of a repair cycle asset item
|
AFTO Form 350, Reparable Item Processing Tag
|
|
To verify the Daily Document Register (D04), a requesting organization or shop should retain what Air Force (AF) Form
|
2413, Supply control log
|
|
Within how many hours is a submission of a Category I deficiency report required?
|
24
|
|
What are the three classifications of defects for material and equipment?
|
Critical, major, and minor
|
|
What preferred method is Microsoft Access to draft and submit deficiency reports?
|
DREAMS II
|
|
A commander assures that property is receiving proper care and is being properly safeguarded by
|
making frequent visits to base activites
|
|
Which type of responsibility is assumed by an individual who has acquired physical possession of government property?
|
Custodial
|
|
When using a 12 inch torque wrench handle with a 3 inch extension to torque a flight control bolt to 120 inch-pounds, what is the proper torque setting?
|
96 inch-pounds (T x La/La + Ea)
|
|
When setting your torque wrench prior to torquing a self-locking nut for a tail drive shaft clamp, you must figure out the
|
nut friction torque and add it to the required torque value
|
|
The proper way to store a torque wrench is with the
|
handle at the lowest setting
|
|
The C-8 type tensiometer is capable of measuring cable tension from
|
10 to 200 pounds with an accuracy of 95 percent
|
|
Which special tool is used to measure the flight control surfaces in degrees of travel?
|
Propeller protractor
|
|
What happens when the battery voltage on the digital protractor drops below 7 volts?
|
The LCD displays "LOW BAT"
|
|
How many threads must be showing through a self-locking nut for maximum locking effect?
|
2
|
|
Left hand threads on a turnbuckle can be idenitifed by the
|
groove on the end of the barrel
|
|
When securing widely spaced bolts by double-twist safetying method, how many bolts may be wired in a series?
|
3
|
|
How many turns per inch are allowed on .020 guage safety wire?
|
9-12
|
|
What is the purpose of Air Force Technical Order (AFTO) Form 245, Industrial/Support Equipment Record (Continuous Sheet)?
|
A continuance sheet for AFTO Form 244, Industrial/Support Equipment Record
|
|
What Integrated Maintenance Data System (IMDS) roster shows a documented record of your certified powered support equipment qualifications?
|
Special certification roster
|
|
On a piece of powered support equipment that is operationally ready, but not required for use, a service inspection should be accomplished every
|
7 days
|
|
Which optional feature can be installed on the -86 to provide 28.5 volts direct current (VDC)?
|
Transformer rectifier
|
|
On the -86 generator control panel, the indication of a clogged air filter is a
|
yellow air service indicator flag
|
|
What is another name for engine wash cart
|
Spray unit cart
|
|
On the engine wash cart, the mixer assembly produces a water to soap ratio of
|
4:1
|
|
When you start the first high pressure pump motor in the A/M27T-2A hydraulic test stand, approximately how many seconds must must you wait before you proceed to the next system so that the motor can go into the "run" configuration?
|
3-4
|
|
With the motor running on the A/M27T-2A hydraulic test stand, which valve should you press to relieve any air that was trapped in the system from the fill and bleed operation?
|
Bleed
|
|
What is the maximum output of the MC-2A air compressor?
|
200 psi
|
|
Up to how many feet can the MA-3 ground air conditioner unit be self-propelled using battery power?
|
200
|
|
what must be replaced on the nitrogen cart after dehydrating 16 cylinders of gas?
|
Purifier Cartridge
|
|
What is the purpose of the cellophane wrap on the separation membrane on the Self Generating Nitrogen Servicing Cart (SGNSC)?
|
Necessary for proper function and nitrogen production
|
|
The hydraulic relief valves on the hydraulic filler and pressurization unit are set at what maximum and minimum levels to relieve the low and high pressure systems from excessive pressure?
|
100 psi (low); 3,300 psi (high)
|
|
What is the maximum height, in feet, of the B-1 stand?
|
10
|
|
What is the maximum weight, in pounds, allowed on the B-5 maintance stand
|
600
|
|
What is the maximum height, in feet, of the B-7 stand?
|
16
|
|
Prior to lowering jacks and helicopter, you must check
|
and remove all obstructions
|
|
What is the maximum lifting capacity, in pounds, of the J-1 hoist
|
5,000
|
|
The usual way of counteracting torque in a single rotor helicopter is to
|
use an anti torque tail rotor
|
|
A pilot would use autorotation
|
during an emergency landing with an engine failure
|
|
To correct for the dissymmetry if lift, the helicopter uses
|
a flapping hinge
|
|
Which helicopter flight characteristic usually develops during takeoff or landing and when the helicopter/tiltrotor is 87 to 95 percent airborne?
|
Ground resonance
|
|
What is incorporated into the cyclic system to prevent gyroscopic precession?
|
offset linkage
|
|
Which aircraft design allows for stronger and lighter structure?
|
Semi-monocoque
|
|
An aircraft weight and balance update is required
|
when a component weighting five or more is removed or installed.
|
|
The fuel servicing point is identified by a black
|
four-pointed star
|
|
What form of corrosion occurs from the combined effects of abrasion and wear and corrosion at the interface of two contacting surfaces?
|
Fretting
|
|
Which of these is not part of corrosion prevention
|
Removing rust
|
|
You should not clean exterior plastic surfaces with
|
cheesecloth
|
|
What method of cleaning aircraft can damage/deteriorate sealants, paint coatings, elastomers; disbond adhesives, and craze plastics?
|
Steam cleaning
|
|
When washing the engines and the outside air temperature is between 5 degrees fahrenheit and 40 degrees F, what should the percentage ratio mix of methanol or isopropyl alcohol in the water solution be?
|
60% water and 40% methanol or isopropyl alcohol
|
|
Lubrication charts showing what type of lubricant to use on aircraft components can be found in
|
the applicable -2-1 aircraft technical order (TO) or IETM for the CV-22
|
|
Lubrication that are stored in containers larger than 1 quart must first be
|
filtered before use
|
|
All of the following are publications that apply to aircraft towing except
|
AFI 21-101
|
|
What is the minimum number of tow crewmembers necessary for a normal towing operation
|
Three
|
|
To lessen the danger of a tripod jack pivoting while it supports helicopter, you should
|
make sure two legs of the tripod jack are parallel to the fuselage centerline
|
|
Who should remove the safety devices on live ammunition prior to launching an aircraft?
|
Qualified weapons personnel
|
|
What is the proper sequence to ground an aircraft after flight
|
Ground to aircraft
|
|
Pertaining to navy shipboard personnel, what color jersey does a safety officer wear?
|
White
|
|
When refueling, what is the minimum safe distance between aircraft?
|
50 feet
|
|
Before you move the aircraft into fuel cell, you first
|
purge and dry the tanks
|
|
To stay in constant contact with the aircrew during ground operations, you should
|
use the aircraft intercom system
|
|
Which troubleshooting aid is designed to promote understanding of the system?
|
Schematic
|