Reading...
Play button
Play button
Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
55 Cards in this Set
- Front
- Back
|
SPREADER-OPERATING CONTROLS
|
LEFT-OPEN, 9 SECONDS
RIGHT- CLOSED, 5 SECONDS |
|
|
SPREADER-OPENING DISTANCE
|
28"
|
|
|
SPREADER-OPERATING SPEED
|
OPEN AND CLOSED AT A CONSTANT RATE
|
|
|
SPREADER-MAXIMUM SPREAD FORCE
|
20,026 lbf
|
|
|
SPREADER-MAXIMUM PULL FORCE
|
9,840 lbf
|
|
|
SPREADER-WEIGHT
|
54.9
|
|
|
SPREADER/ CUTTER-COUPLINGS
|
QUARTER-TURN AUTOMATIC LOCKING COUPLING
(MAKE SURE NOT UNDER PRESSURE) |
|
|
TNT C-25 CUTTER
OPERATING CONTROLS |
LEFT-OPEN, 4 SECONDS
RIGHT- CLOSED, 5 SECONDS |
|
|
TNT CUTTER
OPERATING SPEED |
OPEN AND CLOSE AT A CONSTANT RATE
|
|
|
TNT CUTTER
OPENING DISTANCE |
6.375"
|
|
|
TNT CUTTER
MAX CUTTING FORCE (BOLT NOTCH) |
109,098 lbf
|
|
|
TNT CUTTER
MAX CUTTING FORCE ( BLADE CENTER) |
55,000 lbf
|
|
|
TNT CUTTER
WEIGHT |
41 LBS
|
|
|
TNT TLS-50- RAM
operating controls |
LEFT-OPEN, 59 SECONDS AVERAGE
RIGHT- CLOSED, 29 SECONDS AVERAGE |
|
|
TNT TLS-50- RAM
OPERATING SPEED |
OPEN AND CLOSED AT A CONSTANT RATE
|
|
|
TNT TLS-50- RAM
CLOSED LENGTH |
21.5"
|
|
|
TNT TLS-50- RAM
EXTENDED LENGHT |
50.32"
|
|
|
TNT TLS -50 RAM
MAXIMUM 1ST PUSH FORCE |
51,500 lbf
|
|
|
TNT TLS-50-RAM
MAXIMUM 2ND PUSH FORCE |
18,500 lbf
|
|
|
TNT TLS -50-RAM
WEIGHT |
46.3
|
|
|
TNT TLS RAMS ARE NOT DESIGNED TO DO WHAT?
|
AS A TOOL FOR PULLING
|
|
|
TNT TLS -25-RAM (HEAVY RESCUE)
OPERATING CONTROLS |
LEFT-OPEN, 31 SECONDS AVERAGE
RIGHT- CLOSE, 15 SECONDS AVERAGE |
|
|
TNT TLS-25-RAM
CLOSED LENGHT |
16.75"
|
|
|
TNT TLS - 25-RAM
EXTENDED LENGHT |
32.75"
|
|
|
TNT TLS - 25-RAM
MAXIMUM 1ST PUSH FORCE |
51,5000 lbf
|
|
|
TNT TLS - 25-RAM
MAXIMUM 2ND PUSH FORCE |
18,500 lbf
|
|
|
TNT TLS - 25-RAM
WEIGHT |
40 lbs
|
|
|
QUICK-CUT AIR HAMMER
DEFINITION |
HEAVY-DUTY CHISEL AND A LIGHT DUTY PNEUMATIC BREAKER FOR USE ON
RESCUE OPS EXTRICATIONS FORCIBLE ENTRY |
|
|
QUICK CUT
WEIGHT |
5 lbs
|
|
|
QUICK CUT
LENGHT |
10 INCHES
|
|
|
QUICK CUT
MAXIMUM OPERATING PRESSURE |
300 PSI
|
|
|
QUICK CUT
OPERATES ON WHAT SOURCE |
ANY AIR SOURCE, CYLINDER OR COMPRESSOR
|
|
|
QUICK CUT
AIR CONSUMPTION AT 100 PSI |
8 CFM AVERAGE
|
|
|
QUICK CUT
BLOWS/ MINUTE |
2200
|
|
|
QUICK CUT
NORMAL OPERATING PRESSURE |
150-200
|
|
|
CUTTING PLASTIC
|
50-100
T 11" |
|
|
CUTTING FIBERGLASS
|
50-100
T 11" |
|
|
CUTTING LIGHT SHEET METAL
|
80-120
CURVED, DUAL, T PANEL 7, 11, 18 |
|
|
CUTTING BUILDING METAL SKIN
|
90-130
CURVED, DUAL 7, 11, 18 |
|
|
CUTTING METAL ROLLING DOOR
|
90-150
CURVED 7,11,18 |
|
|
CUTTING AIRCRAFT SKIN
|
100-150
CURVED, DUAL, T PANEL 7, 11, 18 |
|
|
BREAKING CONCRETE BLOCK
|
120-150
POINTED, FLAT 18" |
|
|
BREAKING CONCRETE
|
140-200
POINTED, FLAT 18" |
|
|
CUTTING CAR DOOR POST
|
150-175
CURVED 7, 11, 18 |
|
|
CUTTING DOOR HINGES
|
175-250
CURVED 7, 11, 18 |
|
|
HYDRA RAM
DEFINITION |
PRESSURIZED FORCIBLE ENTRY TOOL FOR INTERIOR SWINGING DOORS CARRIED ON THE LADDER TRUCK
|
|
|
HYDRA RAM
MAX OPENING WIDTH |
4"
|
|
|
HYDRA RAM
GAINS |
3/4 WITH EACH PUMP
|
|
|
HYDRA RAM
PUMPS FOR FULL EXTENSION |
7
|
|
|
HYDRA RAM
DOORFRAME |
SOLID
|
|
|
HYDRA RAM
CLEAN AND LUBRICATE |
AFTER EACH USE
|
|
|
HYDRA RAM
LUBRICATE PISTON WITH |
3 IN 1 OIL
|
|
|
HYDRA RAM
CLEANING PISTON |
WIPE WITH CLEAN RAG AND OIL AGAIN
|
|
|
HYDRA RAM
AFTER COMPLETION OF OILING |
RETRACT AND EXTEND TOOL A FEW TIMES TO DISTRIBUTE OIL
|
|
|
HYDRA RAM
BUILT UP DIRT |
USE AIR GUN TO BLOW OFF OR WASH WITH WATER
SUBMERGE TOOL IN SOAPY WATER, FLUSH WITH CLEAN WATER, ALLOW TO DRY, THEN LUBRICATE AS DESCRIBED |
