T-Boat Cfr

Front 1

What Are Vital Systems

Back 1

1. Fuel System
2. Fire Main
3. CO2 and Halon Systems
4. Bilge Systems
5. Steering System
6. Propulsion System and Aux controls
7.Ships Service and emergency generation system
8. any engineering system identified by the OCMI.
182.710

Front 2

What vsls are required to have a fire pump

Back 2

A vsl more than 65 feet, a vsl that carries more than 49 passengers, or a ferry vsl
181.300

Front 3

A vsl that carries more than 49 passengers or is greater than 65 ft must have a pump of at least _____ and a pressure of _____?

Back 3

50 GL per min, pressure not less than 60 psi at the pump outlet.

Front 4

Diesel fuel piping of aluminum is acceptable on aluminum hull vessels if it is a minimum of?

Back 4

Schedule 80 wall thickness. 182.455 (a) (1) (i)

Front 5

In addition to adult life jackets a number of child size life jackets equal to at least ____ of the number of persons permitted must be provided

Back 5

10%, 180.71

Front 6

On a vsl less than 65 carring more than 50 pax the minimum capacity o fa fire pump must be?

Back 6

50 gallons per minute, not less than 60 psi at pump outlet and fitted with a gugage. 181.300 (b)

Front 7

In addition to adult life jackets a number of child size life jackets equal to at least ____ of the number of persons permitted must be provided

Back 7

10%, 180.71

Front 8

Lead holes for wood screws should be about ___% of the root diameter of the screw for hardwood and about ___% of the rood diameter for softwoods.

Back 8

90% 70%
NVIC 7-95

Front 9

What is considered wet wood?

Back 9

Above 18% moisture content. NVIC 7-95

Front 10

What vsl's are required to have load lines?

Back 10

79 feet or more, constructed after 7/2/68, on other than domestic voyage. 175.122

Front 11

Who is the prime assigning and issuing authority for loadlines.

Back 11

ABS

Front 12

Who is required to have draft marks?

Back 12

Any vsl with one of the following greater than 65, more than 12 on an international voyage or more than 1 deck above the bulkhead deck exclusive of a pilot house.

Front 13

What are the VA no discharge zones?

Back 13

Smith MT. Lake, Lynnhaven River, Broad Creek.

Front 14

What are the harbors of safe refuge for VA?

Back 14

Rudee Inlet, Cape Charles/Cape Henry, Chincoteague, Ocean City
CID 15

Front 15

What is the required nominal pipe size for bilge pipe?

Back 15

1 in for vsls less than 65 ft, 1.5 for greater.
182.510

Front 16

A CO2 cylinder may be inclined not more than ___ from vertical unless fitted with a flexsible or bent siphon tubes, in which case they may be inclined not more than ____ from vertical.

Back 16

30 deg, 80 deg
181.410 (c)(ii)(7)

Front 17

What are flare and smoke signal requirment for various routes?

Back 17

3 and 3 for lakes bays and sounds, and rivers. 6 and 6 for oceans, coastwise and limited coastwise.

Front 18

What is the definition of Coastwise?

Back 18

A route not more than 20 NM offshore. (Exposed)

Front 19

What is the definition of an exposed route?

Back 19

A route greater than 20 nm from a harbor of safe refuge. (Oceans, Coastwise and Great Lakes)

Front 20

What is the definition of high seas?

Back 20

Greater than 3 nm offshore

Front 21

What is the definition of an Oceans route.

Back 21

Greater than 20 nm offshore (Exposed)

Front 22

For most portions of a steel vessel, without other weakening factors, a local thickness deterioration of up to about ___% may be accepted.

Back 22

25%
NVIC 7-68

Front 23

Steal vsl's built to less than commercial scantlings should generally be replaced when wasted more than ____%

Back 23

15%
NVIC 7-68

Front 24

What is the Steel NVIC?

Back 24

7-68

Front 25

What is Subchapter T part 176?

Back 25

Inspection and Certification

Front 26

What is Subchapter T part 177?

Back 26

Construction and Arrangement

Front 27

What is Subchapter T part 178?

Back 27

Intact Stability and Seaworthiness

Front 28

What is Subchapter T part 179?

Back 28

Subdivision, Damage Stabiliity and Watertight Integrity.

Front 29

What is Subchapter T part 180?

Back 29

Lifesaving Equipment and Arrangements

Front 30

What is Subchapter T part 181?

Back 30

Fire Protection Equipment

Front 31

What is Subchapter T part 182?

Back 31

Machinery Installation

Front 32

What is Subchapter T part 183?

Back 32

Electrical Installation

Front 33

What is Subchapter T part 184?

Back 33

Vessel Control and Miscellaneous Systems and Equipment

Front 34

What is Subchapter T part 185?

Back 34

Operations

Front 35

When doing an air test as field testing for a weld, spaces should be pressed up with ____ psi.

Back 35

1.5-2 PSI

Front 36

What is the maximum allowable for insets?

Back 36

1 in per linear foot up to 4 in.
Inland Barge Guidance

Front 37

When using a drill stop repair, drill holes should be ______?

Back 37

Approx 2 plate thicknes beyond ends of crack. diameter shold be equal to plate thickness.

Front 38

For full pen welds on steel vsl, if greater than ___ the plate must be beveled at ____.

Back 38

1/4" / 60 deg AWS 4.3

Front 39

For salt water service what are the standards for sampling fasteners.

Back 39

10th year of age and every 5th after.
NVIC 7-95

Front 40

Durring the scope of random samplings of fasterings remove a minimum of ___ fastenings pers side.

Back 40

8
NVIC 7-95

Front 41

For wood boats as a rule of thumb, a replacement plank should extend how many frame spaces?

Back 41

At least 6
NVIC 7-95

Front 42

When is a collision bulkhead required?

Back 42

More than 65 feet, carries more than 49 pax, operates in exposed waters, is more than 40 ft and operates on partially protected waters, or constructed of wood after March 11 2001 and operates in cold water.
46 CFR 179.115

Front 43

Any penetration in the hull less than _____ above the deepest load waterline must have _______________?

Back 43

6'' means to prevent water from entering the vsl.
179.350