Reading...
Play button
Play button
Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
61 Cards in this Set
- Front
- Back
|
Forward Armament Interconnection Box does what?
|
- Provides SARJ
Selection, Arming, Release, Jettison of Bomb Bay stores. - Enables the torpedo pre-setter control - Contains the Jettison programmer module |
|
|
Aft Armament Interconnection Box does what?
|
-Selection, Arming, Release, Jettison of Wing stores.
-Dependent on thephysical presence of the forward armament Interconnection Box |
|
|
Arm/Ord Test Panel provides what functions?
|
-monitors continuity of the Aircraft's online armament and ordnance circuits
-If power is removed, online functions of the ARM/ORD systems will be inhibited. -interface between the centeral computer and the A275 -Tested through Arm/Ord sygnog |
|
|
-Pilot Armament control panel has what switches and indications on it?
|
CUE Lights- Master Arm , Bomb Bay, Search PWR
Switches- MASTER ARM (on/off/reset) , BombBay (open/close), Search PWR (on/off) INDICATION- (ARM HAZARD--KILL READY--SONO DISABLE) |
|
|
What does a ARM HAZARD LIGHT indicate?
|
Indicates a malfunction in the MASTER ARM system.
If the light does not extinguish after reset, then the OFF-LINE mode must be utilized. The ARM HAZARD light will not illuminate if MASTER ARM switch is in the ON position. |
|
|
On the Pilots armament control pannel which switch is utilized for the jettison procedures.
|
TOP Jettison switch is for WIng Stores.
BOTTOM Jettison switch is for Bomb Bay stores. |
|
|
What is the DS-ICU for?
|
"Direct Search - Interface Control Unit"
Has no external controls and operates as a link between the Directed Search Mode Select Panel and Weapons in the Bomb Bay. |
|
|
What is the DSMSP?
|
"Direct Search Mode Selector Panel"
Used for Directed (circle) search torpeado launch. To use other Bomb bay stores the switch must be off. Faults-- Flashing light = operator ERROR Steady light = Hardware Fault |
|
|
Armament Safety Circuit Disable Switch is for?
|
FECB - Used to Bypass the landing gear lever switch, permitting kill stores power when landing gear lever is selected down.
Master arm must be on to hold the relay for the dissable switch energized. |
|
|
Can a conventional weapon selected for release be jettisoned at any time?
|
Yes no need to do anything other than toggle the jettison release switch.
|
|
|
Forward Armament Interconnection Box does what?
|
- Provides SARJ
Selection, Arming, Release, Jettison of Bomb Bay stores. - Contains the Jettison programmer |
|
|
Aft Armament Interconnection Box does what?
|
-Selection, Arming, Release, Jettison of Wing stores.
-Dependent on thephysical presence of the forward armament Interconnection Box |
|
|
Arm/Ord Test Panel provides what functions?
|
-monitors continuity of the Aircraft's online armament and ordnance circuits
-If power is removed, online functions of the ARM/ORD systems will be inhibited. -interface between the centeral computer and the A275 -Tested through Arm/Ord sygnog |
|
|
-Pilot Armament control panel has what switches and indications on it?
|
CUE Lights- Master Arm , Bomb Bay, Search PWR
Switches- MASTER ARM (on/off/reset) , BombBay (open/close), Search PWR (on/off) INDICATION- (ARM HAZARD--KILL READY--SONO DISABLE) |
|
|
What does a ARM HAZARD LIGHT indicate?
|
Indicates a malfunction in the MASTER ARM system.
If the light does not extinguish after reset, then the OFF-LINE mode must be utilized. The ARM HAZARD light will not illuminate if MASTER ARM switch is in the ON position. |
|
|
On the Pilots armament control pannel which switch is utilized for the jettison procedures.
|
TOP Jettison switch is for WIng Stores.
BOTTOM Jettison switch is for Bomb Bay stores. |
|
|
What is the DS-ICU for?
|
"Direct Search - Interface Control Unit"
Has no external controls and operates as a link between the Directed Search Mode Select Panel and Weapons in the Bomb Bay. |
|
|
What is the DSMSP?
|
"Direct Search Mode Selector Panel"
Used for Directed (circle) search torpeado launch. To use other Bomb bay stores the switch must be off. Faults-- Flashing light = operator ERROR Steady light = Hardware Fault |
|
|
Armament Safety Circuit Disable Switch is for?
|
FECB - Used to Bypass the landing gear lever switch, permitting kill stores power when landing gear lever is selected down.
Master arm must be on to hold the relay for the dissable switch energized. |
|
|
Can a conventional weapon selected for release be jettisoned at any time?
|
Yes no need to do anything other than toggle the jettison release switch.
|
|
|
During Bomb bay jettison is it nessecary to open the bomb bay before you select the jettison switch?
|
No, the open cycle of the jettison procedure is in the first 10 seconds but doors open at 3-4 seconds.
|
|
|
During the Jettison BOMB Bay cycle the bomb bay starts to close at what point in the 20 second timer?
|
The 11th second
|
|
|
when the wings only jettison is done how long does it take to complete?
|
8 seconds and they are released in pairs.In 2 second intervals
|
|
|
True or False the ordanance stations must be visually inspected to ensure against a hung store.
|
True
|
|
|
The CDB provides what to the Harpoons system?
|
supplements the AFT ARM Interconnection box for harpoon missle control capability.
Provides: Switching, Sequencion, and Interlock functions required to Select, Prepare, and Launch missiles singly or in pairs. |
|
|
Harpoon Interconnection Box is used for?
|
Contains and Routes WIRING between the DPC, CDB and HARPOON MISSILE SIM.
|
|
|
Connector P418 on the Harpoon Interconnection Box WHEN?
|
SLAM-ER is connected to (11, 13, 14, 16) failure to do so could result in inadvertant damage to Harpoon DPC.
|
|
|
Why is the Mad breaker on the NAV-J box important for the harpoon system?
|
Enables anolog-to-digital conversion of Pitch, Roll, and heading inputs to the DPC
|
|
|
How does the tacco check the fuse delay on the maverick missle.
|
The Fuselage door on the weapon momentarily must be removed. (instantaneous, Delay-1, Delay-2
|
|
|
what does SLAM-ER stand for?
|
Stand off Land Attack Missle - Expanded Response
|
|
|
Mixed load out requirements on the wing are what?
|
No mix with different harpoons. i.e. SLAMER and HARPOON. Harpoon and MAVERICK are OK and SLAMER and MAVERICK are ok,
|
|
|
what does he AMIB do?
|
( Advanced Missile Interface Box)
The AMIB is Used to route SLAMER, Maverick, and AIMS video, Missile status, Control and Launch signals, Armament interlock and KILL READY signals. |
|
|
The junction box is what (J-BOX)?
|
A mount for the AMIB and also provides interface requirements to the HACLCS
|
|
|
The Voyager requires what amount of warm up time?
|
6 mins
|
|
|
whats the stand off for the SLAMER AWW-13 POD when marriage checks are in progress?
|
4ft observer posed
|
|
|
what important to know when loading airspeed data for the SLAMER checks on the Ground?
|
Airspeed must be selected to under 100ft , because the system will turn on the burner to the true airspeed probe. Causing a burn hazard to personnel on deck.
|
|
|
What stations does the SLAMER POD attach too?
|
station 15
|
|
|
In the AIC-41 system what provides the function of the communications switching?
|
Data switch and the digital bus interface.
|
|
|
What do the UHF 1 and VHF FDCI bypass switches actually bypass?
|
The pilot bypass switch will
bypass the FDCI, Data Switch, Digital Bus, and Digital Audio Interface (DAI) Converter |
|
|
what is the purpose of the UHF2 panel assembly in the F RACK?
|
UHF-2 secure
FM imagery LOS transmission capabilities |
|
|
what is CDLS used for on the
P-3? |
Enables the AIP P-3 to downlink wide band sources, primarily imagery to theater friendly forces,
|
|
|
what is the terms RL and FL for the CDLS system?
|
Forward Link
Return Link |
|
|
How many different data rates are utilized with the CDLS system?
|
Standard - 10.71 Mbps
44.73 Mbps 2 Mbps 200 kbps - designed to only carry voice |
|
|
Were does the CDLS system amplify RF signals and provide antenna power from?
|
The RFE, Radio Frequency Electronics Assembly
|
|
|
Which component in the CDLs system interfaces with the VDC and the Tactical computer for transmission over a 10/100 base T ethernet connection?
|
AMA, Airborne Modem Assembly
|
|
|
the CDLS antenna assembly is designed to point at the STE and it has the capabuility to track a max of ____________ STE?
|
5 Surface Terminals
|
|
|
what is th stand off for the
ASC-39 system? |
2 feet
|
|
|
where is the CDLS signal to be transmitted converted in to RF?
|
In the AMA
|
|
|
How many modes of Operation do the ASN-179 INS have?
|
4, STBY, ALIGN, NAV, ATT REF
|
|
|
How long does it take to ALIGN the ASN-179 INS in the Normal mode?
|
4 mins
|
|
|
what 3 things does STBY mode in the ASN-179 system do?
|
1. BIT routine are RUN
2. Zero- Lock Laser Gyro lasers are fired 3. Instruments begin the leveling process |
|
|
what type of Alignments are there with the ASN-179 system?
|
4, Normal, Rapid, In-Flight, Hybrid
|
|
|
what two alignments are necessary with an ARN-151 GPS.
|
Inflight, Hybrid
|
|
|
At what speed in a normal alignment will the A/C switch to a hybrid alignment if motion is sensed?
|
20 knots
|
|
|
At what point in a hybrid alignment does it become to much speed and swap to an inflight alignment?
|
80 knots
|
|
|
what does ATT REF mode not give you?
|
A/C LAT and LONG
|
|
|
what are two differences that the GEM V Module porvides to the CN-1714 that the ASN-179 was not capable of?
|
Reciever Autonomous Integrity Monitoring (RAIM) and Fault Detection And Exclusion (FDE)
|
|
|
what is RAIM?
|
the ability of the Reciever to determine if the integrity of the Navigation solution meets the integrity requirements. requires to be tracking atleast 5 satellites.
|
|
|
What is FDE?
|
Is the ability of the reciever to detect and exclude a bad satellite.
|
|
|
What is a Y mode?
|
Eyncrypted, PPS- precise Positioning Service
|
|
|
Why is the AMIB important for TCDL?
|
Because it routes the inertial data from the RINU-G to the TCDL AMA for positioning data being sent to the STE.
|
