Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
190 Cards in this Set
- Front
- Back
Name the four main areas under which hazards are classified. |
Biological, Chemical, Ergonomic, Physical |
|
A tool that is not working properly and not taken out of service would be classified as what type of hazard? |
physical. |
|
You are working on a roof top unit and find dead pigeons inside the unit. What classification of hazard have you found? |
Biological |
|
The hazard classification that best describes back injuries due to a poor fit between you and your work environment is: |
Ergonomic |
|
When you work with solders that contain lead you should wash your hands before eating. This procedure reduces the risk of which hazard? |
Chemical |
|
When entering a confined space where harmful fumes or a deficiency of oxygen may occur, a plumber must: |
wear respiratory equipment. |
|
When working in confined spaces, it is recommended that torches be ignited and extinguished: |
outside the confined space. |
|
Before entering a vessel to make repairs, a plumber should insist on testing the vessel for: |
fumes and oxygen deficiency. |
|
Hydrogen sulphide gas (H2S), found in oil and gas wells in concentrations as low as 0.07% (700 ppm), may cause: |
unconsciousness and death. |
|
Who is responsible for making available personal protective equipment specified by a provision in the OH & S Act, Regulation and Code? |
your employer |
|
Who is responsible for the actual usage of the personal protective equipment supplied? |
You the employee |
|
When working around welding operations you must wear eye protection due to three types of harmful rays that you may encounter. What are the three types of harmful rays? |
Visible, Infrared , Ultraviolet |
|
When must your employer ensure that you are wearing safety footwear? |
Where danger of injury to your feet exists |
|
identify the three elements necessary for fire to occur. |
Air, Heat, fuel |
|
What is the minimum amount of oxygen needed in the atmosphere to sustain fire? |
16% |
|
Class A fire is classified as: |
Ordinary Combustibles |
|
A 4A ULC rated extinguisher can extinguish a fire that is how much larger than the base amount? |
4 times |
|
What must take place in solids and liquids before burning can occur (before the fuel can ignite into flames)? |
Vaporization of the surface must take place. |
|
Who is responsible for maintenance of a portable extinguisher once it is in service? |
the owner/operator |
|
What is the primary safety feature of an industrial plant site? |
automatic sprinkler system |
|
When is it safe to enter the building after a fire? |
when the all-clear signal is given |
|
When are you ineligible for compensation as the result of an accident? Workers' Compensation Act Section 19(1)(a) |
if the injury is attributable primary to your serious and wilful misconduct |
|
If an accident disables you for part of a day, how much regular salary do you receive? Workers' Compensation Act Section 20(1) |
full day |
|
How soon should you report a personal injury accident? Workers' Compensation Act Section 27(1) |
as soon as practicable after the accident |
|
If you are an apprentice and are entitled to Workers' compensation because of an accident, how much compensation will you receive? Workers' Compensation Act Section 62(2) |
an amount that may be adjusted during the time you have become qualified in your trade |
|
Above what height must an employer have a guardrail erected for a temporary work area? |
3.5 metres |
|
Where a worker is to enter a confined space that is impractical to ventilate, when shall a worker perform tests to check for harmful substances? |
before entering and periodically while the worker is inside |
|
A load on a scaffold must not exceed what percent of the designed load for the scaffold? |
25% |
|
A scaffold plank must be constructed of number one grade lumber of what minimum size? |
51 by 254 mm (2" by 10") |
|
According to Handi Guide 136(b), the base of an inclined ladder shall be no further away from the base of a wall than: |
one quarter of the vertical height where the ladder contacts the wall. |
|
According to Handi Guide 171(b), the employer shall ensure that cylinders containing acetylene are: |
secured in a vertical position. |
|
The side rails of every ladder shall extend what minimum distance above any platform or landing? |
3 feet/ 1 meter |
|
|
1 Meter |
|
At what height must guardrails be installed on scaffold platforms? |
Guardrails should be not less than 0.92 nor more than 1.07 metres |
|
Class B fire is classified as |
Flammable liquids and gases |
|
If platforms are a specified height, a toe-board must be installed when there may be workers below. What is the platform height that requires toe-boards to be installed? |
Where it is possible for materials to fall more than 1.8 metres or 3.5 meters from a temporary platform. |
|
What is the minimum distance from the edge of the trench that the material removed from an excavation (spoil pile) must be kept? |
3.28 ft or 1 meter |
|
On hard compact soil, trenches must be cut back _____ degrees from vertical. |
30 |
|
On all other soils, it must be cut back _____ degrees from the vertical. |
45 |
|
Class C fire is classified as: |
Electrical |
|
When is it necessary to install guardrails around the perimeter of the roof? |
Where it is possible for a worker to fall a vertical distance greater than 3.5 metres from a temporary work area or 1.2 metres from a permanent work area. |
|
Is it possible for workmen to remain on scaffolds while they are being moved if The height of the work platform does not exceed twice the shortest base dimension and the surface over which it will travel is firm, level and free of hazards that may cause the scaffold to topple. True / False |
True |
|
Planks must extend a minimum of _____ mm and not more than _____ mm beyond all edges. |
150 mm, 300 mm |
|
Known safety hazards that could cause injury and cannot be controlled have to be brought to the attention of workers. True or false |
True |
|
Workers shall not smoke within 3 metres of a vehicle while it is being refuelled. True or false |
True |
|
It is a worker's responsibility to ensure that he is wearing appropriate eye protection when there is a danger of injury to the eye. True or false |
True |
|
The height of rise must be uniform throughout the length of a stairway. True or false |
True |
|
When a worker is using equipment that has not been properly maintained, it is permissible to use it as long as adequate care is taken. True or false |
False |
|
Workers may work without industrial protective headwear where a danger to their head exists, if their employer has provided an alternative method of protecting their head. True or false |
True |
|
An employer must make available at the work site any equipment that a worker is required to wear to perform in accordance with the regulations. True or false |
True |
|
A worker shall not work under a raised vehicle unless it is supported by substantial stands or blocks other than jacks. True or false |
True
|
|
A worker who is not competent must be directly supervised by a competent worker. True or false |
True |
|
It is a violation of the regulations for a worker to use personal protective equipment that is not in good condition. True or false |
True |
|
A worker has forgotten to remove a lockout device and has left the work site. The employer can remove the lockout device as long as no worker will be endangered by the removal. True or false |
True |
|
One part of a code of practice for entry into a confined space is that there must be rescue procedures and a list of rescue equipment. True or false |
True |
|
A worker using an electric arc welder is responsible to see that fellow workers are protected from the flash. True or false |
True
|
|
A worker must be protected from falling from a permanent work area if the fall could be greater than 1.2 metres. True or false |
True |
|
A worker shall not use more than 10 psi of compressed air to blow dust from clothing. True or false |
False |
|
A competent worker must inspect all respiratory protective equipment that is not used routinely, at least once per month. True or false |
True |
|
A positive means must be installed to prevent a press or shear from operating while the worker's body is in the danger zone. True or false |
True |
|
The load to which a scaffold is subjected should at no time exceed the equivalent of ½ of the load for which it is designed. True or false |
False |
|
A worker shall not shift a belt on a machine by hand while the belt is in motion. True or false |
True |
|
A trench could be a confined space. True or false |
True |
|
When there is danger of an injury, a worker must use a push stick or block for feeding materials into cutting or shaping machinery. True or false |
True |
|
When installing shoring in a trench, a worker shall use a ladder and work upward from the bottom of the trench. True or false |
False |
|
A worker shall not work one metre from the top of a portable single or extension ladder. True or false |
False |
|
In an immediate dangerous to life situation where respiratory protective equipment is required, a worker must wear air purifying type respiratory protective equipment. True or false |
False |
|
Signallers on a work site must be _____ _____, and made visible by the wearing of a _____. |
Clearly distinguishable, Highly visible vest |
|
The signallers shall be designated by the _____. |
Employer |
|
The equipment operator is required to take all signals from the _____ _____ except a 'STOP' signal. |
Designated signaller |
|
Sufficient illumination of the work site to ensure safe working conditions shall be provided by the _____. |
Employer |
|
Housekeeping which provides safe working conditions shall be ensured by the _____. |
Employer |
|
Generally, lumber used to meet requirements in these regulations must be _____ or better and must be at least _____ grade. |
Spruce, # 2 grade |
|
Workers and equipment shall not operate within _____ metres of live overhead power lines. |
7 meters |
|
Machinery which is out of service for repair must be _____. |
Locked out and tagged |
|
Operators of explosive activated fastening tools must be _____ , and _____ in the use of each model of tool the operator may be called on to use. |
Instructed and trained |
|
The maximum revolutions per minute of a grinder output shaft is identified on the grinder and is used to select the proper abrasive wheel or disc, as recommended for safe use in the manufacturer's specifications and is identified on the wheel or disc. True or false |
True |
|
A worker shall grind on the side of an abrasive wheel but shall not adjust a tool rest while the grinder is in motion. True or false |
False |
|
A worker shall not work from the top _____ rungs or steps of a portable ladder. |
2 |
|
Where there is a danger created by the movement of a load during a hoisting operation the load may be controlled by the use of _____ lines. |
Tag |
|
Workers shall not ride on a material hoist. True or false |
True |
|
Rigging equipment should be thoroughly checked for safety before each ____ _____. |
Work shift |
|
Sharp edges which could cause damage to rigging equipment must be _____ . |
Guarded |
|
A hook used in a circumstance where the dislodgement of the hook could cause injury to workers must have _____ _____ _____ or _____ to prevent dislodgement. |
Safety latch, mousing and latch to prevent dislodgement |
|
Wooden scaffolding must be made of _____ _____ lumber and must have a strength _____ times the weight of the load. |
Unpainted, dressed, lumber and must have a strength 4 times the weight of the load. |
|
Metal scaffolding must be erected, used, maintained and dismantled in accordance with? |
Manufacturers specifications |
|
An "excavation" is defined as: Any dug out area of ground other than a trench, tunnel, underground shaft or an open pit mine. True or false |
True
|
|
A "spoil pile" means is defined as: material excavated from an open pit mine. True or false |
False |
|
A "temporary protective structure" is defined as: a structure or device designed to provide protection in an excavation, trench, tunnel or underground shaft from cave-ins, collapses or sliding or rolling materials, includes shoring, bracing, piles, planking or cages. True or false |
True |
|
A "trench" is defined as an elongated dug out area of ground whose depth is equal to its width at the bottom. True or false |
False |
|
Workers entering excavations and trenches which exceed 1.5 metres in depth must be protected from: _____ and _____ material. |
Cave-ins and slide material |
|
Where are you ineligible for compensation as the result of an accident? |
If the injury is attributable primarily to your serious and willful misconduct. |
|
How soon should you report a personal injury accident? |
As soon as practical after the accident. |
|
Above what height must an employer have a fall protection system (Guardrail, harness, etc) for a temporary work platform. |
3m |
|
Above what height must an employer have a toeboard erected for a temporary work platform? |
3.5M |
|
A tool rest on a fixed grinder must be: |
Set to a maximum of 3mm (1/8th") from the face of the wheel. |
|
A tool rest on a fixed grinder must be set within how many millimeters of the face of the wheel? |
3mm |
|
Guardrails made of lumber must be at least. |
38mm x 89mm (2" x 4") |
|
The lateral (Horizontal) spacing between vertical members of a guardrail system must be no more than: |
2m |
|
A free standing or rolling scaffold must not exceed ____ times the smallest base dimension. |
3 times |
|
A load on a scaffold must not exceed ____ percent of the designed load for the scaffold? |
25% |
|
A scaffold plank must be constructed of number one grade lumber of what minimum size? |
51mm x 254mm (2" x 10") |
|
What is the ratio for a ladder? |
4 vertically for every 1 horizontally. 4:1 |
|
If a portable ladder is used as a means of access to a platform, then the side rails of the ladder must extend above the platform at least: |
1M |
|
The employer shall ensure that cylinders containing acetylene are: |
Secured in a vertical position. |
|
Who is responsible for informing a new employee about the dangers of a controlled product? |
The employer |
|
A MSDS must be reviewed whenever new information becomes available, or at least how often? |
Every three years |
|
Where is the supplier label attached? |
To the container the product is shipped in. |
|
What precaution must be taken prior to any welding being initiated on enclosed or boxed-in sections? |
Determine if the interior contains a flammable substance. |
|
When entering a confined space where harmful fumes or a deficiency of oxygen may occur, you must: |
Wear respiratory equipment.
|
|
Before entering a vessel to make repairs, you should insist on testing the vessel for: |
Fumes and oxygen deficiency. |
|
Permanent eye damage in the form of cataracts may result from over exposure to which harmful light ray? |
Infared |
|
Which type of radiant energy can cause welding flash? |
Ultra violet. |
|
What must be done where the general public is exposed to harmful welding rays? |
Put up proper screens and warning signs. |
|
What should you do if you receive a major contact burn? |
Immediately cool the burned area by immersing it in cool, still water. |
|
Hearing protection should be worn where the noise level is above: |
85 decibels |
|
Which type of glove is recommended for oxyfuel cutting? |
Dry-tanned leather gauntlet style. |
|
A carbon dioxide fire extinguisher is best suited for: |
Class B or C fires |
|
a class C fire involves |
Electrical equipment |
|
A class D fire involves |
Combustible metals |
|
What type of fire can be extinguished with water? |
Class A |
|
When welding on metals plated with cadmium: |
Appropriate respiratory protective equipment should be used. |
|
Which metal, when heated or welded, can produce metal fume fever if the fumes are inhaled? |
Zinc |
|
H2S found in oil and gas wells in concentration as low as 0.07% 700 PPM may cause: |
Unconsciousness and death |
|
Why is a fit test important when using a respirator? |
To prevent inward leaks of contaminated air. |
|
If you suspect that a fellow worker is overcome by hydrogen sulphide gas, what is the first thing you should do before attempting a rescue? |
Put on a pressure demand respirator. |
|
What is a red seal program? |
Allows you to work in any participating province as a journeyman. |
|
Who is responsible for safety in the workplace? |
Employer and the employee |
|
Who is responsible for determining the course outline for the steamfitter - pipefitter trade? |
The provincial apprenticeship committee |
|
Who is responsible for recommending that the apprentice receive time credit for past experience in the trade? |
The employer. |
|
Who is responsible for the blue book? |
The apprentice |
|
Inhaling metal fumes may result in: |
Zinc chills |
|
What is the formula to determine F.A. |
Throw - Tread engagement = Fitting allowance |
|
Spiral reamers can be used on power vises? True or False. |
False |
|
The safest way to use a wrench is to: |
Pull on it with steady pressure. |
|
When tightening fittings and pipe together, what should be used? |
A back-up wrench. |
|
When you use a knot in a rope it will decrease the rope strength by? |
50% |
|
Personnel lifts have a safety factor of? |
10:1 |
|
A material lift has a safety factor of? |
5:1 |
|
What is the minimum size wet vent for a toilet? |
2" |
|
When using wire rope clamps how are they to be installed? |
U-Shaped portion on the running end |
|
Which dimension would be the longer? Face to face Centre to Centre End to End Centre to End |
Centre to Centre |
|
How far past your FPNO BWV can you take off your 1st branch? |
24" or 2 feet |
|
Shock loading may lead to? 3 points. |
1. Bird caging 2. Damage to load 3. Rope breakage |
|
How many threads should you have on a threaded pipe? |
10-12 |
|
What is the minimum sling angle? |
30 degrees |
|
What is the recommended sling angle? |
60 degrees |
|
The three types of flared fittings are the 45 flar, inverted 45 flare, and the _______ 37 flare. |
SAE |
|
High pressure compression fittings are rated up to ____ PSI |
10,000 |
|
Schedule 40 black iron pipe is rated up to _____ PSI |
150 |
|
When transitioning form ABS to PVC do you need primer? |
Always the PVC fitting or pipe. |
|
What kind of knot would you use to join two dissimilar diameters lengths of rope? |
Sheet bend |
|
All threaded fittings have a tapered thread and are installed |
Clockwise |
|
A balanced oxy-fuel torch is best for |
Welding, Brazing, heating, Not cutting |
|
What should be done to a gas cylinder before protective caps are removed? |
Should be secured |
|
Why do you crack a cylinder before attaching the regulator? |
To clean dust from the valve. |
|
What colour are oxygen lines on an oxy-fuel set-up? |
Green |
|
On a kitchen sink, how many degrees change in direction are you allowed before a clean out must be installed? |
90 degrees |
|
It is good plumbing practice to install ____ at the base of every stack. |
A cleanout |
|
Building sewers in Calgary are to be no smaller than |
4" |
|
When flaring soft copper tubing, you must always ____ in order to form a proper flare. |
Ream the pipe |
|
Compression nuts are only manufactured in one style True or false |
False |
|
High pressure compression fittings are rated up to ____ psi |
10,000 |
|
When tightening flared fittings you should not to over _____ the joint and always use a back-up wrench. |
Tighten |
|
Do not use a sling if it: |
Does not have a tag seems unduly worn is frayed has cuts or gouges |
|
The "killer knot' is another name for the |
Square knot |
|
In a residential application, a cause of not enough hot water could be: |
Cracked dip tube on the HWT |
|
What is the most likely cause of a WC leaking at it's base. |
Wax seal damaged
|
|
A leaking T and P valve can be plugged until it can be fixed or replaced. True or false. |
False |
|
When threading 1" black iron pipe, what size chases are yo be put into the universal die head? |
1"-2" always go with the higher size. |
|
All pex and Poly-B are interchangeable if... |
You have an adapter fitting. |
|
What is the recommended number of turns after solvent welding plastic pipe and fittings? |
1/4 Turn |
|
Know dis |
|
|
What does this symbol mean? |
Stop |
|
What does this symbol mean? |
EMERGENCY STAHP |
|
What does this symbol mean? |
Dog everything |
|
What does this symbol mean? |
Hoist load |
|
What does this symbol mean? |
Lower load |
|
What does this symbol mean? |
Boom up |
|
What does this symbol mean? |
Boom down |
|
What does this symbol mean? |
Swing |
|
What does this symbol mean? |
Make movements slowly |
|
What does this symbol mean? |
Raise load slowly |
|
What does this symbol mean? |
Lower load slowly |
|
What does this symbol mean? |
Raise boom slowly |
|
What does this symbol mean? |
Lower boom slowly |
|
What does this symbol mean? |
Lower the boom and raise the load |
|
What does this symbol mean? |
Raise the boom and lower the load |
|
What does this symbol mean? |
Shorten the boom |
|
What does this symbol mean? |
Extend the boom |