Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
42 Cards in this Set
- Front
- Back
Minimum pipe size for building sewer connected to public sewer |
4” |
|
Minimum size for building cleanout in Canada? |
4” |
|
Minimum slope of a trap arm must be what %? |
2% |
|
Minimum main stack size for single family dwelling? |
3” |
|
If a sewer is opened and a characteristic rotten egg smell is detected which gas should be suspected? |
Hydrogen sulphide |
|
Maximum direction change on a trap arm? |
Dependent on type of discharge the fixture will have |
|
No water closet may be installed in a room that is not: a. Waterproof b. Properly lighted and ventilated c. Equipped with a lav d. Suitable for privacy |
B |
|
Minimum size of wet vent serving WC |
2” |
|
Maximum size of of trap arm draining into wet vent? |
2” with exception of emergency floor drain |
|
What type of valve is most widely used in the industry? |
Ball valve |
|
Two main types of checkvalves |
Lift check Swing check |
|
What type of valve is most suited for throtting? |
Globe valve |
|
4 disc types for globe valves? |
Conventional Composition Plug Needle |
|
Which 4 valves can accommodate flow in either direction? |
Gate Ball Plug Butterly |
|
What color is abs dwv? |
Black |
|
Which plastic DWV pipe has highest temp resistance? |
ABS |
|
Which plastic pipe is used for underground gas? |
High density polyethylene |
|
Nesting pipes refers to? |
Storing smaller diameter pipes in larger diameter pipes |
|
2 plastic tubes best suited for radiant panel heating? |
Pex Pe/al/pe |
|
When connecting plastic to metal pipe with a thread the plastic must have the _______ thread |
MIP |
|
What types of plastic produce toxic gases? |
PVC/ CPVC |
|
What is used to keep plastic pipe round when threading? |
A round wooden plug |
|
What are the 3 methods of joining cast iron pipe approved by the NPC? |
Lead and oakum Mechanical joint Compression joint |
|
When installing bell and spigot cast iron, in which direction should the sewage flow through the pipe? |
Out of the spigot into the hub |
|
When installing bell and spigot cast iron, in which direction should the sewage flow through the pipe? |
Out of the spigot into the hub |
|
2 methods of cutting cast iron? |
Snap cutters Hammer and chisel |
|
2 Disadvantages of cast iron vs copper pipe |
Heavier Poor resistance to shock |
|
How is glass pipe joined? |
Mechanical joint couplings |
|
List one advantage of glass pipe |
Low expansion rate |
|
List one advantage of glass pipe |
Low expansion rate |
|
List 2 methods for joining fibreglass pipe. |
Butt and strap Bell and spigot Flanged Threaded and bonded O ring bell and spigot |
|
What is the safety concern when using lead? |
It is known to cause cancer in the state of california |
|
Name 4 historical piping systems. |
Lead pipe Bituminized pipe Vitrified clay pipe Aluminum pipe Caulked cast iron Asbestos cement soil pipe Wood pipe |
|
Which grade of threaded pipe should be used with max pressure of 1000psi? |
XXS |
|
What does the schedule number on a pipe designate? |
Pressure/stress ration x1000 |
|
What are alloys in metal pipes? |
Other material mixed with iron to produce special qualities in pipe |
|
What is the angle on a national or american standard pipe thread? |
60 degrees |
|
Why is dope applied to threaded joints? |
Lubrication |
|
Two types of steel pipe cutters? |
Single wheel Multi-wheel |
|
As pipe size increases the number of threads per inch generally ____________. |
Decreases |
|
All pipe fittings have a _____________ thread |
Tapered |
|
Where would you see a parallel thread? |
A bolt |