Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
149 Cards in this Set
- Front
- Back
How do you check the viscous dampers?
|
With a flashlight and mirror
|
|
What is the limitation for the bubble in the viscous damper?
|
refer to daily deck and mims
|
|
What must be done to the viscous damper prior to a wash job?
|
Wrap with barrier paper or bag to prevent water intrusion.
|
|
Why do you look at the ADB prior t starting a Daily?
|
For duplicate MAFs and what maintenance has been performed
|
|
What is used to clean the aircraft?
|
MIL-PRF-85570, Aircraft cleaning compound (MRC-350, 14 Day)
|
|
What is the number of flame detectors in each engine bay?
|
2; 1 on the deck and one on the bulkhead
|
|
What is the number of flame detectors in the APU compartment?
|
1 on the bulkhead
|
|
If there is a missing fastener on the TGB cowling, what must you do prior to launching?
|
Perform an immediate FOD search, replace if in a corner position or write a MAF against it.
|
|
What is the fastener policy?
|
Refer to the SOP in the front of the NATOPS (look up for answer)
|
|
How long do you have to wait to check the engine oil after shutdown?
|
20 minutes
|
|
How long do you have to wait to check the APU oil after shutdown?
|
1 hour
|
|
What does IRAC stand for?
|
Interim Rapid Action Change
|
|
What does the letter "C" stand for in the MRC daily deck?
|
Corrosion prone areas
|
|
State the definition of a warning
|
Steps that are not followed may result in death or serious injury
|
|
State the definition of a caution
|
Steps that are not followed may result in damage to equipment
|
|
State the definition of a note
|
Steps that require extra emphasis
|
|
What is the 36 inch rule?
|
It means you should check all areas that are within 36 inches of the area that you are working in.
|
|
What is a windmill?
|
when the tail rotor spins out of control due to the lack of a tail boot or TR indexer
|
|
What is the first step in folding the tail?
|
Install tail rotor boot
|
|
Name 3 areas that have copper-beryllium on the rotor head
|
Pitch horn bushings (where the pitch locks drive in)
Droop stops Lock pin pullers |
|
What should be done if any blade drops during a blade fold evolution?
|
Notify maintenance control and perform conditional inspection
|
|
Where should the NC-10 or 108 be parked when in use on aircraft?
|
Outside the rotor arch to prevent the exhaust from burning the blade
|
|
What must be done if the yellow blade stops movement 3/4 of the way around during blade fold evolutions with APU running?
|
Shut down APU or go back to spread
|
|
On what cards would you use a Duel Chuck Stem Gauge?
|
Cards 6.1, 12.1, and 15.2
|
|
What is the limitation for folding the tail?
|
45 knots
|
|
What PPE is required when installing the BF crutches and clamps?
|
Cranial
|
|
Can you daily an aircraft then wash the same aircraft and then fly the aircraft?
|
No. Wash jobs are major maintenance
|
|
How do you check the flame detectors?
|
With a red lens and a flashlight. Looking for the appropriate "T" handle to light up in conjunction with the fire warning light on the Master Warning Panel
|
|
How do you perform the fire detection test in the cockpit?
|
Rotate the fire detection knob to position 1 and then to position 2 and checks for the appropriate "T" handle to light up in conjunction with the fire warning light on the Master Warning Panel
|
|
How long is the TA good for?
|
24 hours
|
|
What drives the 24 hour period of a TA?
|
the fuel samples
|
|
how long is a Daily good for?
|
72 hours
|
|
What are the four things to look for on a daily?
|
FOD, Corrosion, Security, and Integrity
|
|
What form is used to document SE pre-op checks?
|
OPNAV 4790/52 card
|
|
who signs the "A" sheet?
|
Plane Captain, qualified Safe for Flight, and the Pilot
|
|
What is the OPNAV 4790/141?
|
"A" sheet, Acceptance Sheet
|
|
What qualified persons are required for an aircraft move?
|
Plane Captain, brake rider, and the tow tractor driver
|
|
What is the max speed to tow an aircraft?
|
5 MPH or as fast as the slowest wing walker
|
|
What mixture is used with below 32 degrees in the windshield washer reservior?
|
50% alcohol and 50% water
|
|
What is the mandatory hand signals that the pilots must obey?
|
Hold and wave off
|
|
What is liquid FOD?
|
any liquid like oil or hydraulic fluid
|
|
What does MSDS stand for?
|
Material Safety Data Sheet
|
|
What items can you find on MSDS sheets?
|
Required PPE, health hazard, emergency spill procedres, manufacturer, emergency first aid procedures
|
|
What is the only servicing you check for during a daily inspection?
|
Air Cycle Machine
|
|
Areas that require extra attentioin during a daily after an aircraft returns from a CAL-LZ?
|
bottom of aircraft for abrasions, punctures, dents, broken lights, etc.
tires for damage and landing gear windscreens for cracks rotor head and hydraulic bay |
|
How do you check oil on the air cycle machine?
|
with an inspection mirror
|
|
Where is the Gland Nut?
|
tail landing gear strut
|
|
What is the NAVAIR 00-80T-109?
|
Aircraft refueling NATOPS Manual
|
|
What are the Primary fuels used in the aircraft?
|
JP-5/JP-8; NATO code: F44, F-34, F-35 See NATOPS 3-6for MIL-SPEC and Commerical grades
|
|
What three publications do you use when washing an aircraft?
|
01-1A-509, MRC-350, Plane Captains Manual
|
|
What is the minimum flash point of the fuel in the aircraft fuel cell to be moved into the hangar bay?
|
above 120 degrees F (01-80T-109)
|
|
What oil is used in the aircraft engine?
|
MIL-PRF-23699
|
|
What is the alternate engine oil?
|
MIL-PRF-7808 (NATOPS 3-14)
|
|
What oil is used in the APU?
|
MIL-PRF-23699
|
|
What is the alternate APU oil?
|
MIL-PRF-7808 (use only in temperatures below -13F/-25C
|
|
How many times do you check your tools?
|
A minimum of 5 times
|
|
Who is responsible for maintaining your plane captain qualification?
|
the plane captain
|
|
what must be done prior to starting your Daily inspection?
|
Review the ADB
|
|
What does ADB stand for?
|
Aircraft Discrepancy Book
|
|
Can you take fuel from an unmarked fuel truck?
|
yes, check the paperwork to verify what fuel is in the truck.
|
|
Who is authorized to ride in the cain during an aircraft move?
|
nobody
|
|
how many position lights are on the SH-60R?
|
3; Tail, Port stub wing and STBD stub wing
|
|
How do you determine the correct pressures on the fire bottles?
|
Use the "Temperature vs Pressure Plate" located on the fire bottle and the "Free Air Thermometer" located on the center windscreen
|
|
How many people are required to fold the tail pylon?
|
5
|
|
What are the positions?
|
3 on the pole, 1 on the stab and 1 on the crack wrench
|
|
What oil is used in the Main Transmission?
|
DOD-PRF-85734
|
|
What is the rag policy on the boat?
|
Rags must be checked out even though the rags come in bundles
|
|
Can you fuel an aircraft with no electrical power?
|
Yes, unless you need to monitor fuel load
|
|
What is the teeter test?
|
Refer to T/A for Procedures
|
|
What oil is used in the Intermediate Gearbox
|
DOD-PRF-85734
|
|
Can PRIST be used in the MH-60R?
|
yes in the pre-mixed form. Not the Aerosol can
|
|
Name 2 dangers of the RAST probe
|
The RAST probe has a CAD. The emergency down actuation of the probe can cause serious injury or death
|
|
Where should you wing walk if the blades are folded?
|
outside the imaginary rotor arch
|
|
Where do you chock an aircraft if there is a M-299 with the Hellfire or a CATM loaded?
|
STBD main mount or the tail
|
|
How many people are authorized to be on the engine bay work platform?
|
1 man 300 lbs max
|
|
How many quarts of oil will an empty engine require?
|
7.3 quarts (GAI-010, engine servicing)
|
|
What does it mean to have a NON-CRITICAL ONLY Flight Deck Physical?
|
it means that you can do Daily and Turn Around inspection but cannot be on the flight line during flight evolutions
|
|
How long do you have to wait to cycle blade fold motor?
|
10 minutes, to not burn out the motor
|
|
What instruction gives a daily requirement?
|
4790.2b NAMP
|
|
What oil is used in the Tail Gearbox?
|
DOD-PRF-85734
|
|
What is the Hydraulic fluid that goes into the Hydraulic Reservoirs?
|
MIL-PRF-83282
|
|
What is the access numer for the ESC access panel?
|
6.2.5
|
|
What is the access numberfor the right MLG strut access panel?
|
2.2.5
|
|
List the CB that must be pulled prior to starting Daily inspection
|
Daily Deck, 3.3, 3.4, 3.5, and 3.6
|
|
What does the warning state concerning the AAR-47 sensors?
|
Daily deck card 4.5
|
|
What are the 2 areas on the MLG that require liquid "A"?
|
Exposed areaof shock strut piston and the jack pads
|
|
What type of Enine does the MH-60R have?
|
T700-GE-401C
|
|
With the TR pylon folded, what steps are required only at sea?
|
Clean canted bulkhead
spray canted bulkhead with CPC inspect lockpin lug and hinge lugs for disruption in sealant Daily Deck Card 10.4 Note |
|
What are the warnings associated with the inspection of the disconnect jaw?
|
daily deck card 10.8 and 10.9
|
|
what is a hydraulic swivel fitting?
|
a swivel fitting that allows hydraulic fluid to b transferred from the aircraft to the TR pylon.
|
|
What is done to the stabilator actuator on each daily inspection?
|
wipe exposed piston with low lint and liquid A
|
|
Where are the leak limitations for the TRIM/BOOST servos located?
|
GAI-000 WP013 Daily deck card 18.1
|
|
Where are the potential chaffing locations on the MGB radiator and fan located?
|
daily deck card 23.3 note
|
|
What is the A1-H60CA-MRC-100?
|
turnaround checklist
|
|
What must be done is Sonobuoys are installed on the aircraft during a TA?
|
ensure rotary valve is in the vent postiion and the rotary lockpin is in the locked position.
TA card step 2.8 |
|
How many fire extinguishers are on the MH-60R?
|
2; TA card 2.10
|
|
When do you check exterior lighting?
|
during the TA. TA step 11
|
|
What is the APU accumulator pressure?
|
2700-3100 psi. TA card step 15
|
|
When do you check the tail bumper skid pad?
|
During the TA. TA card step 25
|
|
what could cause erroneous fuel readings?
|
shorting plug. TA card step 33. warning
|
|
how much time should elapse after engine shutdown before oil can be checked?
|
20 minutes
|
|
what is the MLG tire pressure?
|
100 +/- 5psi
|
|
what are the TLG tire pressures?
|
105 +/- 5psi
|
|
What is the A1-H60RA-NFM-000?
|
NATOPS
|
|
What is the A1-H60CA-GAI-010?
|
Plane captain's manual
|
|
What order do you install crutches and clamps to a folded aircraft?
|
red, black, blue, yellow
|
|
What areas wshould be wrapped during an aircraft wash?
|
refer to GAI-010 aircraft wash procedures
|
|
What is the cleaning solution for heavy duty washing?
|
1 part aircraft cleaning compound to one part fresh water
|
|
Can you fuel an aircraft without the aircraft battery installed?
|
no. GAI, refueling, step i
|
|
How many seconds should it take for the high level sensors to significantly reduce the flow of fuel or stop it completely?
|
5-10 seconds
|
|
What is the max fuel cell capacity of the 2 main cells?
|
592 gallons
|
|
What is the proper way to ground an aircraft
|
install ground first then aircraft, remove: aircraft first then ground
|
|
what do you service the engine oil to?
|
approximately 1 inch below the full mark.
|
|
what is the TD-1B?
|
aircraft tie down chain NA 17-1-537
|
|
What publication would you find the P/N for ordering chains?
|
NA 17-1-537
|
|
What towbar is used ot tow the MH-60R?
|
24 ALBAR
|
|
What publication would you find information on the 24 ALBAR?
|
NA 17-1-537. ACsecuring and handling procedures
|
|
What position should the tail lockpin be in during aircraft moves?
|
down. NA 17-1-537
|
|
What is the NA 00-80T-109?
|
aircraft refueling manual
|
|
What is the NA 00-80T-113?
|
aircraft signals NATOPS
|
|
What is the NA 00-80R-14?
|
aircraft firefighting and rescue manual
|
|
What is OTTO fuel II?
|
a stable liquid mono-propellant used in the propulsion of the MK 46 Torpedo
it is bright red, freeflowing, oily liquid that is heavier than water a deadache lasting for several hours after exposure is the chief symptom of vapor inhallation, although nausea may develop after prolonged exposure. skin absorption of OTTO fuel may also cause headaches |
|
What should be performed for interal engine fire?
|
internal engine fires usually result when residual fuel is dumped into the engine on shutdown.
-these fires may be controlled by windmilling the engine. - if this procedure fails, an extinguishing agent must be directed into the engine - application of Halon 1211 or CO2 must be accomplished at a distance so that the Halon 1211 or CO2 enters the fire area in gaseous form. NA 00-80R-14, 6.3 |
|
How many PDI's are on the aircraft?
|
14; 2 on each hyd pump, 1 PAM, 2 each engine, 2 #4 reservior, 1 MGB
|
|
What servicing can you NOT check while the tail pylon is folded and why?
|
IGB, TGB
|
|
Before checking out the hydraulic PMU, what must you check?
|
check if a current hydraulic sample has been run that day
|
|
What is the maximum acceptable class for Hydraulic S.E.?
|
class 3
|
|
The foregn object damage prevention program NAMPSOP is found in what chapter of the 4790.2B?
|
chapter 10
|
|
Approximately how much fuel should be taken from the low point drain when taking hydraulic samples?
|
one pint
|
|
What is the plane captain disgnation form?
|
4790/158
|
|
what kind of inspection is an engine waterwash?
|
conditional inspection
|
|
what is the most corrosive metal on the MH-60R?
|
magnesium
|
|
what is the most common metal present on the MH-60R?
|
aluminum
|
|
Who's responsibility is it to maintain a FOD free environment?
|
all hands
|
|
what form of corrosion is an extremely localized attack that results in holes in the metal?
|
pitting 509 vol 1
|
|
what is the most common type of corrosion?
|
uniform surface corrosion
|
|
when slewing the stabilator to level postion, what kind of power must be used?
|
external power
|
|
based on average reaction time, acraft will continue to move how many after an unaticipated stop signal is given?
|
6 to 9 feet
|
|
when securing MRB while spread, tiedown deflection of blade tips shall be how many inches from static postion?
|
6-12 inches
|
|
Before applying pwer to the aircraft, the plane captain must ensure that all cockpit switches are in what position(s)
|
off safe or normal
|
|
who is the only person that can authorize an aircraft move with no brakes?
|
maintenance officer
|
|
what instruction and chapter defines the responsibilities, basic dutines, and qualifications of a plane captain?
|
4790.2B ch10
|
|
servicing units must be set to what maximum pressure before fueling?
|
55 psi
|
|
where would you find what constitues a corner fasterner on TGB cowling?
|
NATOPS SOP (front pages)
|
|
What are you testing when doing the BIM test ona daily inspeciton?
|
testing the operation on the BIM indicator
|
|
what is the lab bottle used for on a daily inspection
|
washing the gland nut with fresh water
|
|
what does corrosion look like on aluminum?
|
white to gray powder
|
|
what does corrosion look like on magnesium?
|
white, powdery, snow like mounds, and white spots on surface
|
|
how do you wash an aircraft?
|
start at the lower surfaces, working upward and out
|