Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
87 Cards in this Set
- Front
- Back
Give the formula for propagation speed |
C= frequency * wavelength
|
|
Propagation speed is dependent on what?
|
The medium
|
|
If density increases what happens to the propagation speed?
|
decreases
|
|
Give the formula for wavelength
|
wavelength= c/ frequency
|
|
give the units for frequency
|
Hz or MHz
|
|
Give the units for Period
|
seconds or microseconds
|
|
Give the units for wavelength
|
meters or millimeters
|
|
Give the units for propagation speed
|
m/sec or mm/microsecond
|
|
Give the units for PRF
|
H or kHz
|
|
Give the units for PRP
|
seconds or microseconds
|
|
Give the units for Pulse Duration
|
seconds or milliseconds
|
|
Give the units for Duty Factor
|
Duty factor is unitless!
|
|
Give the units for SPL
|
millimeters
|
|
Give the units for Amplitude
|
Megapascals (MPa)
|
|
Give the units for Power
|
Watts or milliwatts
|
|
Give the units for Intensity
|
watts/cm^2
|
|
Give the units for the Beam Uniformity Ratio (BUR)
|
BUR is unitless!
|
|
Give the units for Attenuation
|
Decibels
|
|
Give the units for the attenuation coefficient
|
dB/cm
|
|
Give the units for Impedence
|
Rayls
|
|
Give the formula for SPL
|
SPL= n * wavelength
OR SPL= (n*c)/frequency |
|
Give the formula for Pulse Duration
|
PD= n * T
|
|
Give the formula for Duty Factor
|
DF= (PD/PRP) * 1000
OR DF= (PD*PRF)/1000 |
|
Give the formula for Intensity
|
Intensity= Power/Area
|
|
Describe the Temporal average intensity to the Peak average intensity
|
Intensity TA = Intensity PA * DF
|
|
Give the formula for Beam Uniformity Ratio
|
BUR= SP/ SA
|
|
Give the formula for Attenuation coefficient
|
Ac= 1/2 frequency
|
|
Give the formula for Attenuation
|
Attenuation= Ac * Length
OR Attenuation= 1/2frequency * length |
|
Give the formula for the Half Value Thickness Layer
|
HVTL = 3/ Ac
OR HVTL = 6/ frequency |
|
Give the formula for Impedence
|
Z= density * c
|
|
Give the formula for the Intensity Reflected Coefficient
|
IRC= [(Z2-Z1)/(Z2+Z1)]^2
|
|
Give the formula for the Intensity Transmitted Coefficient
|
ITC= 1- IRC
|
|
Give the formula for Snell's Law
|
[sine incident angle/ sine transmitted angle]= c1/c2
|
|
Give the formula to solve for the distance of the reflector
|
D= 1/2 [c * time]
t represents round trip time |
|
The average round trip distance of a reflector can be solved using which rule?
|
13microseconds/1cm Rule
aka the rule of 13 |
|
Define frequency
|
number of cycles per second
|
|
Define period
|
time it takes for one cycle to occur
|
|
Define wavelength
|
The length of one complete cycle
|
|
Define PRF
|
the number of pulses per second
|
|
Define PRP
|
Time from the begin of one pulse to the beginning of the next pulse
|
|
Define PD
|
time it takes for one pulse to occur
|
|
Define Duty Factor
|
Fraction of time the transducer is generating a pulse (when it's on)
|
|
Define SPL
|
Length of a pulse
|
|
Define Amplitude
|
Variation of a given sound wave, indicates strength
|
|
Define Power
|
Rate at which energy is transferred
|
|
Define Intensity
|
Rate at which energy passes through an area
|
|
Define the Beam Uniformity Ratio
|
unitless ratio that describes the distribution of the sound beam intensity
|
|
Define Attenuation
|
weakening of a sound beam
|
|
Define the Half Value Thickness Layer
|
distance intensity must travel to be reduced by half the original intensity
|
|
Define Backscatter
|
sound travels back in the direction it came from
|
|
How many pulses are in a pulsed wave cycle?
|
2-3
|
|
How many pulses are in a Doppler wave cycle
|
5- 30
|
|
Describe the relationship between power, intensity, and amplitude
|
Power is congruent to Intensity
Power is congruent to Amp^2 Intensity is congruent to Amp^2 |
|
Describe the purpose of Focusing a beam
|
Decreases the area of the sound beam therefore increases the intensity
|
|
Where is the Spatial Peak intensity found
|
At the beam center
|
|
What is the most common intensity used in pulsed wave?
|
SPTA
|
|
Where is SPTP used?
|
In continuous wave, is the highest intensity
|
|
What is the purpose of a hydrophone?
|
measures the intensity of a sound beam
|
|
When does a specular reflection occur?
|
When the wavelength is larger than the boundary and the surface is smooth
|
|
What kind of boundary does perpendicular incidence encounter?
|
A 90 degree angle
|
|
What kind of boundary does an oblique incidence encounter?
|
Any angle other than 90 degrees
|
|
Give the 3 criteria for Snell's Law
|
1. need 2 different c
2. need to hit at oblique angles 3. incident angle = reflected angle |
|
Give the 2 requirements for Refraction to occur
|
1. oblique incidence
2. different propagation speeds on each side of the boundary |
|
Refraction is strongly dependent on?
|
Impedence
|
|
What will cause scattering?
|
1. size of reflector is equal or less than the wavelength
2. a rough surface |
|
List the contrast agents used in the U.S
|
1. Definity
2. Imagent 3. Optison |
|
What are the purposes of contrast agents
|
1. improve lesion detection
2. improves weakened Doppler signals |
|
List the acoustic variables
|
1. Pressure
2. Density 3. Particle vibration |
|
Give the formula for NZL
|
NZL= (apeature)^2/(4*wavelength)
OR NZL= (aperature)^2*freq/4*c |
|
Give the formula for Q Factor
|
Q= operating freq./ Bandwidth
|
|
What is the purpose of damping material?
|
used to reduce number of cycles in a pulse to improve resolution
|
|
What is sacrificed with damping material
|
sensitivity
|
|
What is the damping material composed of?
|
epoxy resin and metal powders
|
|
What is another name for damping material?
|
Backing material
|
|
How thick are ultrasound elements typically?
|
0.2-1mm
|
|
Describe the relationship between crystal thickness and frequency
|
The thicker the crystal the lower the frequency
The thinner the crystal the higher the frequency |
|
Describe the matching layer in relation to the crystal wavelength
|
matching layer = 1/4 wavelength of the crystal
|
|
What determines the Near Zone Length?
|
aperature and operating frequency
|
|
What is another name for near zone?
|
Fresnel zone
|
|
Describe the relationship between NZL, aperature, and frequency
|
Increase aperature, increase NZL
Increase frequency, increase NZL |
|
What is another name for the far zone?
|
Fraunhofer zone
|
|
Describe the width of the transducer element at the end of the NZL and at double the NZL
|
End of NZL beam width= 1/2 transducer element width
Double NZL beam width = transducer element width |
|
Focusing can only be accomplished in what zone?
|
Fresnel zone aka near zone
|
|
Annular array transducers are __ steered and __ focused
|
mechanically steered, electronically focused
|
|
Define aperature
|
Size of the ultrasound element
|
|
Define apodization
|
outer elements are driven at lower amplitudes than inner elements to reduce grating lobes
|
|
Define matching layer
|
Placed in front of transducer to reduce reflection at the transducer/element interface
|