P-360 Programing Parameters

Front 1

BEvT

Back 1

Battery Evaluation Time
Time in seconds the tool averages battery voltage for evaluation purposes.
10 seconds

Front 2

BThr

Back 2

Low Battery Threshold
The voltage threshold below which the tool will alert the operator or switch to battery 2. LoVWthr in XXT
23 volts

Front 3

CMTF

Back 3

Correct for Magnetic TFA Declination
Enables or disables the correction for magnetic declination at surface or down hole.
Surface

Front 4

DiAA

Back 4

Auto Data Acquisition Control
Allows putting the directional data acquisition process in automatic data mode for test purposes.
Off

Front 5

DipT

Back 5

Dip Angle Tolerance
.60 degrees

Front 6

DwnL

Back 6

Downlink commands
Enables or disables the Downlink capabilities of the system.
Disable

Front 7

EvIM

Back 7

Evaluation Mode
Tells the tool to derive the inclination during the survey sequence only, or during both the survey and toolface/logging sequence.
Survey

Front 8

FDM

Back 8

Flow Detection Method
Switch

Front 9

FEvT

Back 9

Flow Evaluation Time
How long the flow input must indicate a state change before the system will respond to the change. Stored in the tool. Must be the same as PEvT.
5 seconds

Front 10

GrvT

Back 10

Gravity Magnitude Tolerance
.006

Front 11

Gsf

Back 11

Gamma Scale Factor
Multiplier which is applied to gamma counts.
1

Front 12

GSPC

Back 12

Gamma Sensor Power Control
When enabled, the sensor is powered only during flow conditions. Always set to enable.
Enable

Front 13

HdCK

Back 13

Type of Header Check Bits
The method used to confirm the accuracy of received data.
Parity

Front 14

HiPL

Back 14

High pulse Amplitude Limit
Pulses higher than this limit will not be reported or processed. Set to a value higher than the pulse amplitude. The ratio of HiPL:LoPL is typically set to approximately 10:1, but can be adjusted as needed.
300 PSI

Front 15

IncT

Back 15

Inclination Threshold
The inclination at which the tool will switch from magnetic to gravity tool faces.
5 degrees

Front 16

InvF

Back 16

Invert Flow Sense
Off

Front 17

Loc

Back 17

Jobsite Location
Enter the well name.
From well plan

Front 18

LoPL

Back 18

Low Pulse Amplitude Limit
Pulses lower than this limit will not be reported or processed.
30 PSI

Front 19

MagT

Back 19

Magnetic Field Tolerance
.005

Front 20

MDec

Back 20

Magnetic Declination
degrees

Front 21

ModN

Back 21

Mode Number
Determines which of the four different modes the tool will use.
1

Front 22

NDip

Back 22

Nominal Dip Angle
From Well Plan

Front 23

NGrv

Back 23

Nominal Gravity
1.000 G

Front 24

NMag

Back 24

Nominal Magnetic Field Strength
From well plan

Front 25

NSyP

Back 25

Number of Sync Pulses
Number of single wide pulses in a sync word.
4, 3 in benchtree

Front 26

PALMode

Back 26

Pulse Amplitude Limit Mode
When manual, the system uses the defined LoPL and HiPL. When auto, the system calculates the LoPL and HiPL.
Auto in XXT, not available in benchtree.

Front 27

PEvT

Back 27

Pumps On/Off Evaluation Time
How long the pumps input must indicate a state change before the system will respond to the change. Must be the same as FEvT.
5 seconds

Front 28

PmpT

Back 28

Pumps On Threshold
The pressure threshold above which the receiver considers the pump to be on. The setting for this variable depends on the expected pressure.
500 PSI

Front 29

PTfs

Back 29

Pressure Transducer Rating
The nominal pressure rating for the pressure transducer. Usually set to 10000 PSI

Front 30

PTG

Back 30

Pressure Transducer Gain
A multiplier used to increase pressure readings.
1

Front 31

PTO

Back 31

Pressure Transducer Offset
0

Front 32

PWTmg

Back 32

Type of Pulse Width Timing
Use narrow when the signal noise ratio decreases and there is a low level of pulse distortion. Use wide when pulses become distorted and are being rejected.
Normal

Front 33

RxDT

Back 33

Receiver Delay Time
The time delay required from pumps on until the receiver begins looking for signals from the tool.
45 sec

Front 34

RxFBwF

Back 34

Filter Bandwith Factor
1

Front 35

SHSz

Back 35

Survey Header Size
The number of bits in a survey header.
3

Front 36

SuAM

Back 36

Survey Acquisition Mode
Tells the tool whether to acquire survey data during the "Flow" or "No Flow" state.
No Flow

Front 37

SuDT

Back 37

Survey Acquisition Delay Time
Delay time from a "No Flow" state until the data acquisition process occurs.
25 sec

Front 38

SyTy

Back 38

Sync Word Type/Format
The type of Sync word generated by the tool.
1111

Front 39

SyWF

Back 39

Sync Window Factor
The amount of time that the receiver will look for sync pulses, before indicating that it missed sync. A value of zero indicates an infinite sync window.
0

Front 40

THSz

Back 40

Toolface/Logging Header Size
The number of bits in a toolface/logging header.
3

Front 41

TLTx

Back 41

Toolface/Logging Transmission Time Limit Control
In mode 1,2,3 or 4. Tells the tool how long, in minutes, to transmit toolface/logging data. A value of zero means the tool will continue to transmit data until pumps off.
0

Front 42

TmpT

Back 42

High Temperature Threshold
125

Front 43

TxDT

Back 43

Transmit Delay Time
The time delay required from "Flow On" until the tool begins to transmit signals
60 sec