Network Appliance Ns0-163 Bank A

Front 1

You can unlicense the cluster feature only in _____ mode with cluster _____.

Back 1

normal, disabled

Front 2

The snapvault snap sched -x command can be used to:

Back 2

Schedule incremental backups

Front 3

If the local node has its FC HBA connected to switch Bank 1, it owns the disks connected to switch bank ___.

Back 3

2

Front 4

Which three of the following configurations would increase data transfer rates for traditional volume SnapMirror?

Back 4

1.The destination and source contain disks of the same size.
2.The destination and source contain RAID groups of the same size.
3.The destination and source contain the same number of RAID groups.

Front 5

Which one of the following keywords alone can be used to convert an
asynchronous mirror to be synchornous?

Back 5

sync

Front 6

When you issue the snapmirror status command, to what does the "Lag"
column refer?

Back 6

The difference between the current time and the last basic snapshot creation time on the source for a
transfer which completed successfully.

Front 7

Which one of the following commands is used to specify the destination
appliance(s) that are allowed to replicate (pull) data from the source appliance?

Back 7

options snapmirror.access

Front 8

Which one of the following options will allow a snapmirror storage appliance to mirror from this system?

Back 8

options snapmirror.access host = <destination_filer>

Front 9

In a synchronous SnapMirror configuration, the source storage appliance
exhibits high latency due to user traffic and rapid data change from SnapMirror transactions. Which one
of the following tuning methods best resolves this performance behavior? Edit the /etc/snapmirror.conf file on the destination storage appliance and set:

Back 9

outstanding=3s

Front 10

Which one of the following does SnapRestore revert?

Back 10

File content

Front 11

Normally, before you split a SyncMirror volume, you ensure that both plexes are _______ and _______.

Back 11

online, operational

Front 12

Node 1 in a clustered pair detects that it has lost connectivity to one of its disk shelves. Node 1 is still up, but it cannot see one of its disk shelves. However, the partner node, Node 2, can see all of Node 1s disk shelves. Which one of the following features will cause Node 2 to monitor this error condition for a period of three minutes (by default), and then forcibly take over Node 1 if the error condition persists?

Back 12

Negotiated Fail Over

Front 13

You have quiesced a volume to stabilize the contents of a destination just prior to a snapshot. What is the next logical command that you would issue after the snapshot is complete?

Back 13

snapmirror resume

Front 14

What command would you enter to restore the /vol/flexvol0/etc/rc file from a snapshot to the /vol/flexvol0/home directory?

Back 14

snap restore -t file -r /vol/flexvol0/home/rc /vol/flexvol0/etc/rc

Front 15

Which command displays the disk ownership for both CPU modules in a
FAS270c appliance?

Back 15

disk show -v

Front 16

Which one of the following commands or procedures would you use to undo a
SnapRestore reversion?

Back 16

None of the above. You cannot undo a SnapRestore reversion

Front 17

You are trying to do a single file SnapRestore for a file, but you are receiving an error message that the directory structure no longer exists. Which one of the following is the most likely explanation?

Back 17

You must recreate the directory structure before trying to restore the file.

Front 18

Five minutes ago, you performed a single file SnapRestore on a large NFS file.
40% of your NFS users are now complaining about getting "stale file handles" for the file. Which one of
the following is the most likely cause of this problem, and the best procedure to correct it?

Back 18

These users are on a different subnet from the others. Start troubleshooting by checking their subnet.

Front 19

In a Fabric Attached MetroCluster, a "disaster" is described as a:

Back 19

Prolonged communication disruption

Front 20

In cluster takeover mode, the shared interface assumes the identity of the
________.

Back 20

local and failed partner interfaces