Reading...
Play button
Play button
Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
30 Cards in this Set
- Front
- Back
|
According to Ohm,s law, what happens to circuit current if the applied voltage (a) increases, (b)
decreases? |
(a) Current increases (b) Current decreases
|
|
|
According to Ohm,s law, what happens to circuit current if circuit resistance (a) increases, (b)
decreases? |
(a) Current decreases (b) Current increases
|
|
|
What is the equation used to find circuit resistance if voltage and current values are known?
|
R= E/I
|
|
|
What is the term applied to the rate at which a mechanical or electrical force causes motion?
|
Power.
|
|
|
How can the amount of current be changed in a circuit?
|
By changing the circuit resistance or the voltage of the power source.
|
|
|
What is the power used in a circuit that has 10 amperes of current through a 10-ohm resistor?
|
1 kilowatt
|
|
|
How much power is converted by a 1-horsepower motor in 12 hours?
|
8,952 watt hours or 8.952 kWh.
|
|
|
What is the efficiency of the motor if it actually uses 9.5 kWh in 12 hours?
|
942 (rounded to 3 places).
|
|
|
A series circuit consisting of three resistors has a current of 3 amps. If R1 = 20 ohms, R2= 60
ohms, and R3 = 80 ohms, what is the (a) total resistance and (b) source voltage of the circuit? |
(a). 160 ohms
(b). 480 volts |
|
|
What is the voltage dropped by each resistor of the circuit described in question 17?
|
E1=60 Volts
E2=180 Volts E3=240 Volts |
|
|
If the current was increased to 4 amps, what would be the voltage drop across each resistor in the
circuit described in question 17? |
E1=80 Volts
E2=240 Volts E3=320 Volts |
|
|
What would have to be done to the circuit described in question 17 to increase the current to 4
amps? |
The source voltage would have to be increased to 640 volts.
|
|
|
When using Kirchhoff ,s voltage law, how are voltage polarities assigned to the voltage drops
across resistors? |
The point at which current enters the resistor is assigned a negative polarity and the point at
which current leaves the resistor is assigned a positive polarity. |
|
|
A circuit has a source voltage of 100 volts and two 50-ohm resistors connected in series. If the
reference point for this circuit is placed between the two resistors, what would be the voltage at the reference point? |
50 volts.
|
|
|
If the reference point in question 25 were connected to ground, what would be the voltage level of
the reference point? |
Zero volts.
|
|
|
What is an open circuit?
|
A circuit where there is no longer a complete path for current flow.
|
|
|
What is a short circuit?
|
An accidental path of low resistance which passes an abnormally high amount of current.
|
|
|
Why will a meter indicate more voltage at the battery terminal when the battery is out of a circuit
than when the battery is in a circuit? |
The internal (source) resistance of the battery will drop some of the voltage.
|
|
|
What condition gives maximum power transfer from the source to the load?
|
When the load resistance equals the source resistance
|
|
|
What is the efficiency of power transfer in question 30?
|
50 percent.
|
|
|
There is a relationship between total current and current through the individual components in a
circuit. What is this relationship in a series circuit and a parallel circuit? |
Total current in a series circuit flows through every circuit component but in a parallel circuit total
current divides among the available paths |
|
|
In applying Kirchhoff ,s current law, what does the polarity of the current indicate?
|
Whether the current is entering the junction (+) or leaving the junction (-).
|
|
|
The total power in both series and parallel circuits is computed with the formula: PT = P1 + P2 +
P3 +...Pn. Why can this formula be used for both series and parallel circuits? |
In both cases all the power used in the circuit must come from the source.
|
|
|
If one branch of a parallel network is shorted, what portion of circuit current flows through the
remaining branches? |
None.
|
|
|
What information must be known to determine the component values for a voltage divider?
|
The source voltage and load requirements (voltage and current).
|
|
|
If a voltage divider is required for a load that will use 450 mA of current, what should be the value
of bleeder current? |
45 mA rule-of-thumb.
|
|
|
If the load in question 50 requires a voltage of +90 V, what should be the value of the bleeder
resistor? |
2 kΩ.
|
|
|
If the source voltage for the voltage divider in question 50 supplies 150 volts, what is the total
current through the voltage divider? |
495 mA.
|
|
|
If the load requirement consists of both positive and negative voltages, what technique is used in
the voltage divider to supply the loads from a single voltage source? |
The ground (reference point) is placed in the proper point in the voltage divider so that positive
and negative voltages are supplied. |
|
|
Is it considered safe for a person to touch any energized low-voltage conductor with the bare
hand? |
NEVER! All energized electric circuits should be considered potentially dangerous
|
