Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
138 Cards in this Set
- Front
- Back
In reference to micrometers in general, which of the following statements is true? |
a) Micrometers should be coated with a light coat of oil to prevent rust
|
|
Dividers are used for which of the following purposes? |
d) Both 2 and 3 above
|
|
The text for this course provides which of the following information? |
All of the above
|
|
Adjustable parallels consist of what number of tapered parts?
a) Two b) Three c) One d) Four |
a) Two
|
|
Registering speed indicators are used for which of the following purposes?
a) To register the speed of light b) To govern the speed of vehicles c) To regulate the flow of fluid d) To count the number of revolutions of shafts |
d) To count the number of revolutions of shafts
|
|
The types of micrometers commonly used are designed so that the longest movement possible between the spindle and the anvil is what distance?
a) 3 inches b) 2 inches c) 4 Inches d) 1 inch |
d) 1 inch
|
|
The frames of micrometers are available up to what maximum size?
a) 10 Inches b) 15 inches c) 46 inches d) 24 inches |
d) 24 inches
|
|
Calipers are used for what purpose? |
d) To measure diameters
|
|
On a vernier micrometer, the ten spaces on the vernier are equivalent to what number of spaces on the thimble?
a) Nine b) Five c) Twelve d) Seven |
a) Nine
|
|
The longest movement possible between the spindle and the anvil of a micrometer is known by which of the following terms?
a) Height b) Depth c) Range d) Width |
c) Range
|
|
To read a vernier caliper, you must be able to understand which of the following scales?
a) Steel rule b) Vernier c) Both 1 and 2 above d) British thermal unit |
c) Both 1 and 2 above
|
|
In reference to the use and care of hand tools and measuring tools, which of the following statements is/are true?
a) A user must have, choose, and use the correct tools in order to do the work quickly, accurately, and safely b) Without the proper tools and knowledge of how to use them, the user wastes time, reduces efficiency, and may face injury c) Both 1 and 2 above d) Using tools comes naturally to most people, and formal training is not normally needed |
c) Both 1 and 2 above
|
|
Angle plates are used for which of the following purposes? |
b) For clamping or holding work vertically
|
|
Personnel working with electricity are usually required to wear gloves made from which of the following materials?
a) Cloth b) Leather c) Nylon d) Rubber |
d) Rubber
|
|
Proper eye protection is of the highest importance for all personnel. Eye protection is necessary because of which of the following hazards?
a) Infrared and ultraviolet radiation b) Flying objects such as sparks, globules of molten metal, or chipped concrete and wood c) Both 1 and 2 above d) Audio vibrations |
c) Both 1 and 2 above
|
|
Slide calipers can be used for which of the following purposes?
a) Finding shaft centers b) Measuring outside dimensions c) Measuring inside dimensions d) Both 2 and 3 above |
d) Both 2 and 3 above
|
|
3/6 can be reduced to which of the following fractions?
a) 1/4 b) 1/8 c) 2/3 d) 1/2 |
d) 1/2
|
|
How many millimeters are in a centimeter?
a) 30 millimeters b) 10 millimeters c) 20 millimeters d) 40 millimeters |
b) 10 millimeters
|
|
How many centimeters are in a meter?
a) 200 centimeters b) 100 centimeters c) 300 centimeters d) 400 centimeters |
b) 100 centimeters
|
|
Who is the most important part of safety procedures?
a) You b) Your immediate supervisor c) The executive officer d) The safety officer |
a) You
|
|
Spring dividers are available in which of the following lengths?
a) 4 to 15 inches b) 2 t o 4 inches c) 2 to 6 inches d) 3 to 10 inches |
d) 3 to 10 inches
|
|
Worker's are often judged by the manner in which they handle and care for their tools. Your own efficiency will be improved if you follow which of the following steps?
a) Organize your tools so that those used most frequently can be reached easily without sorting through the entire contents of the tool box b) Always place the most expensive tools in the bottom of tool box c) Clean your tools at the end of the week rather than after each job d) Store your tools on high shelves where the humidity is lower |
a) Organize your tools so that those used most frequently can be reached easily without sorting through the entire contents of the tool box
|
|
What is the range of an inside micrometer when used with a 1/2-inch spacer?
a) .500 of an inch b) .200 of an inch c) .300 of an inch d) .400 of an inch |
a) .500 of an inch
|
|
Which of the following tools should be used as gages for leveling and setup work?
a) V-blocks and clamps b) Registering speed indicators c) Adjustable parallels d) Angle plates |
c) Adjustable parallels
|
|
Which of the following types of micrometers is/are commonly used?
a) The outside micrometer b) The inside micrometer c) The depth micrometer d) All of the above |
d) All of the above
|
|
Vernier micrometers are designed to measure distances to what nearest accuracy?
a) .1000 of an inch b) .0010 of an inch c) .0001 of an inch d) .0100 of an inch |
c) .0001 of an inch
|
|
On a standard micrometer, one complete revolution of the micrometer screw will move the spindle what distance?
a) .015 inch b) .225 inch c) .125 inch d) .025 inch |
d) .025 inch
|
|
Standard micrometers are designed to measure distances to what nearest accuracy?
a) .002 of an inch b) .001 of an inch c) .004 of an inch d) .003 of an inch |
c) .004 of an inch
|
|
Which of the following types of calipers contain a straight measuring rule?
a) Hermaphrodite calipers b) Transfer calipers c) Slide calipers d) Spring-joint calipers |
c) Slide calipers
|
|
When working with power tools, you should follow all EXCEPT which of the following procedures?
a) Before connecting a power tool to a power source, be sure the tool switch is in the "ON" position b) Check electrical cables and cords frequently for overheating c) Never try to clear a jammed power tool until it is disconnected from the power source d) Never operate any power equipment unless you are completely familiar with its controls and features |
a) Before connecting a power tool to a power source, be sure the tool switch is in the "ON" position
|
|
Protective helmets are made from which of the following materials?
a) Polyethylene b) Polycarbonate c) Both 1 and 2 above d) Perineurium |
c) Both 1 and 2 above
|
|
Which of the following instruments can be used to measure distances beyond the range of calipers?
a) Pullers b) Taps c) Trammels d) Planes |
c) Trammels
|
|
Which of the following is the most common measuring tool?
a) A plumb bob b) A micrometer c) A level d) A rule |
d) A rule
|
|
On a 24-inch or 600-mm caliper, what does .300 inch equal in metric measure?
a) 2.44 nun b) 7.62 mm c) 1.22 mm d) 5.66 nun |
b) 7.62 mm
|
|
If 1/4 equals 16/64, what does ¾ equal in sixty fourths?
a) 48/64 b) 12/64 c) 24/64 d) 56/64 |
a) 48/64
|
|
Electrical workers requiring head protection must wear safety helmets which are capable of withstanding what minimum voltage proof-test?
a) 20,000 volts b) 40,000 volts c) 10,000 volts d) 30,000 volts |
a) 20,000 volts
|
|
What does the size of a micrometer indicate?
a) The total width of the micrometer b) The size of the largest work it will measure c) The total length of the micrometer d) The size of the smallest work it will measure |
b) The size of the largest work it will measure
|
|
The metric system is based upon what multiples?
a) Multiples of 10 b) Multiples of 40 c) Multiples of 30 d) Multiples of 20 |
a) Multiples of 10
|
|
Common tapes and rules usually are NOT graduated smaller than what fraction of an inch?
a) 1/2 inch b) 1/4 inch c) 1/8 inch d) 1/16 inch |
d) 1/16 inch
|
|
A 6-inch micrometer will measure work between which of the following sizes?
a) From 1 to 6 inches thick b) Between 5 and 6 inches thick c) Between 1 and 6 inches thick d) From 4 to 6 inches thick |
b) Between 5 and 6 inches thick
|
|
What type of caliper is used for finding shaft centers or locating shoulders?
a) An outside caliper b) A hermaphrodite caliper c) A vernier caliper d) A slide caliper |
b) A hermaphrodite caliper
|
|
A standard micrometer screw has what number of threads per inch?
a) 40 b) 30 c) 20 d) 10 |
a) 40
|
|
Tool boxes are made from which of the following materials?
a) Steel b) Wood c) Plastic d) All of the above |
d) All of the above
|
|
To measure a piece of stock that is approximately 3 1/4 inches, you will need a micrometer with what range?
a) 1- to 2-inch range b) 2- to 3-inch range c) 4- to 5-inch range d) 3- to 4-inch range |
d) 3- to 4-inch range
|
|
On a metric micrometer, how many revolutions of the spindle is required to move the barrel 1 mm?
a) Three b) Four c) One d) Two |
d) Two
|
|
Regular hard hats must be insulated so that personnel may be protected from voltages up to what maximum amount?
a) 9.000 volts b) 2.200 volts c) 3,000 volts d) 5,000 volts |
b) 2.200 volts
|
|
Wing-type dividers are available in which of the following lengths?
a) 7, 9, and 13-inch lengths b) 5, 9. and 11-inch lengths c) 3, 4, and 10-inch lengths d) 6, 8, and 12-inch lengths |
d) 6, 8, and 12-inch lengths
|
|
A magnetic base indicator assembly is attached to the work surface in what manner?
a) Welded b) Glued c) Magnetically d) Bolted |
c) Magnetically
|
|
On a vernier caliper, what is the difference between the width of one of the 25 spaces on the vernier scale and one of the 24 spaces on the steel rule?
a) 3/1000 of an inch b) 2/1000 of an inch c) 4/1000 of an inch d) 1/1000 of an inch |
d) 1/1000 of an inch
|
|
Which of the following tools should be used for grinding, milling, or drilling purposes?
a) Adjustable parallels b) V-blocks and clamps c) Registering speed indicators d) Angle plates |
b) V-blocks and clamps
|
|
Which of the following statements pertaining to tools is NOT true?
a) You should use each tool only on the job for which it was designed b) Damaged tools should be saved because they can sometimes be used for purposes other than for which they were designed c) A worker's efficiency is often a direct result of the condition of the tools being used d) You should keep an inventory list in your tool box and check it after each job |
Damaged tools should be saved because they can sometimes be used for purposes other than for which they were designed
|
|
On a vernier caliper, the vernier scale is divided into what number of parts?
a) 40 b) 10 c) 20 d) 25 |
d) 25
|
|
The more common types of rules and tapes are divided in which of the following ways?
a) Inches, feet, and yards b) Feet, yards, and meters c) Fractions, inches, and feet d) Inches, meters, and milliliters |
c) Fractions, inches, and feet
|
|
Transfer calipers are used for what purpose?
a) Weighing nuts and bolts b) Holding glued parts together c) Measuring chamfered grooves or flanges d) Threading wire through a bulkhead |
c) Measuring chamfered grooves or flanges
|
|
Safety shoes protect and prevent injury or loss of toes. Some safety shoes are designed to limit damage to your toes from falling objects. What is usually placed in such shoes for protection?
a) Rubber b) Nails c) Steel plates d) Plastic |
c) Steel plates
|
|
Larger tools are generally contained in which of the following types of tool containers?
a) Cantilevered-tray tool box b) Portable-carpenter's tool box c) Canvas too bag d) Mechanic's tool box (chest type) |
d) Mechanic's tool box (chest type)
|
|
On a metric micrometer, one revolution of the spindle advances or withdraws the screw what distance?
a) 0.1 mm b) 0.5 mm c) 1.5 mm d) 1.0 mm |
b) 0.5 mm
|
|
Levels are designed for which of the following purposes?
a)To prove whether a plane is in the true vertical or true horizontal b)To prove whether a surface is in the true vertical or true horizontal c) Both 1 and 2 above d) To remove the rough spots on surfaces |
c) Both 1 and 2
|
|
Which of the following types of levels is used mostly in the
construction industry? a) The machinist's level b) The line level c) The iron bench level d) The striding level |
c) The iron bench level
|
|
What feature on a machinist's level increases its accuracy and sensitivity?
a) Its metallic coating b) Its extra large vial c) Its grooved bottom d) Its light weight |
b) Its extra large vial
|
|
Which of the following levels has a main vial that is used to
determine true horizontal, and two smaller vials that are used to determine true vertical? a) The machinist's level b) The striding level c) The line level d) The master precision level |
d) The master precision level
|
|
Which of the following levels is used to span existing cabling, piping, or similar obstructions?
a) The master precision level b) The iron bench level c) The striding level d) The machinist's level |
c) The striding level
|
|
The carpenter's level has three vials. One vial is mounted
vertically and another is mounted horizontally. The third vial is mounted at what angle? a) 35 degrees b) 45 degrees c) 55 degrees d) 90 degrees |
b) 45 degrees
|
|
A plumb bob is used for which of the following purposes?
a) To establish a true vertical transfer and line-up reference point b) To take readings or soundings in tanks or voids c) Both 2 and 3 above d) To measure the distance between two horizontal points |
c) Both 2 and 3 above
|
|
Plumb bobs are used by which of the following people?
a) Carpenters b) Surveyors c) Maintenance technicians d) All of the above |
d) All of the above
|
|
The surveyor's brass plumb bob may be either a spool type or what other type?
a) An adjustable cap type b) A permanent cap type c) A flexible cap type d) A reverse cap type |
a) An adjustable cap type
|
|
The surveyor’s brass plumb bob comes with what minimum length of nylon, silk, or linen cord?
a) 2 feet b) 4 feet c) 7 feet d) 9 feet |
c) 7 feet
|
|
The surveyor’s brass plumb bobcomes in which of the following sizes?
a) 2, 4, 6, and 8 ounce sizes b) 3, 5, 7, and 9 ounce sizes c) 1, 4. 8, and 9 ounce sizes d) 6, 8, 10, and 16 ounce sizes |
d) 6, 8, 10, and 16 ounce sizes
|
|
Heavier plumb bobs are better for use in which of the following areas?
a) Windy areas b) Sandy areas c) Cold areas d) Hot areas |
a) Windy areas
|
|
In reference to the solid steel plumb bob, which of the following statements is true?
a) It comes in 1, 3, and 10 ounce sizes b) The cord must be obtained from a separate source c) The cord comes with the plumb bob d) It is used when extreme accuracy is required |
b) The cord must be obtained from
a separate source |
|
In reference to plumb bobs, which of the following statements is true?
a) Plumb bobs may be used as a lever b) Plumb bobs should be stored in a humid protective box c) Plumb bobs should be lightly coated with lubricating oil for long periods of storage d) Plumb bobs should receive a heavy coat of oil and should be wrapped in oil-soaked paper prior to being stored for long periods of time |
d) Plumb bobs should receive a heavy coat of oil and should be wrapped in oil-soaked paper prior to being stored for long periods of time
|
|
What are the two basic types of machinist’s scribers?
a) Single point pocket and bent point-straight point b) Straight point and bent point c) Rigid point and flexible point d) Hard point and soft point |
a) Single point pocket and bent point-straight point
|
|
The points on machinist’s scribers can be protected in which of the following ways?
a) By reversing them in the handle b) By placing cork over the points c) By placing soft wood over the points d) All of the above |
d) All of the above
|
|
The carpenter’s square is made up of which of the following parts?
a) The edge and skirt b) The blade and tongue c) The tongue and joint d) The skirt and tongue |
b) The blade and tongue
|
|
What part of a carpenter’s square is used to compute the number of board feet in a given piece of lumber?
a) The brace measure b) The rafter table c) The essex board measure d) The octagon or eight square scale |
c) The essex board measure
|
|
What part of a carpenter’s square is used to find the exact lengths of common braces?
a) The essex board measure b) The brace measure c) The rafter table f) The tongue |
a) The brace measure
|
|
Which of the following tools is used to check lines that are at right angles to each other?
a) A try square b) A flaring tool c) A scriber d) A digging tool |
a) A try square
|
|
A right angle is what number of degrees?
1. 30 degrees 2. 60 degrees 3. 75 degrees 4. 90 degrees |
4. 90 degrees
|
|
Which of the following tools is used for testing bevels and laying out angles?
1. A plumb bob 2. A climbing tool 3. A mattocks 4. A T-bevel |
4. A T-bevel
|
|
To transfer measurements to work and to indicate the parallelism of surfaces, you should use which of the following tools?
1. A dial depth gage 2. A vernier depth gage 3. A surface gage 4. A micrometer depth gage |
3. A surface gage
|
|
Which of the following tools is used to measure the depth of holes, slots, counterbores, and recesses?
1. A snap gage 2. A telescoping gage 3. A two-piece collet die 4. A rule depth gage |
4. A rule depth gage
|
|
In reference to a vernier depth gage, which of the following
statements is/are true? 1. It consists of a graduated scale that is either 6 or 12 inches long 2. It has a sliding head that is designed to bridge holes and slots 3. It cannot enter holes less than 1/4 inch in diameter 4. All of the above |
4. All of the above
|
|
Which of the following tools can be used to measure the thickness of paint?
1. A dial depth gage 2. A rule depth gage 3. A machinist's level 4. A master precision level |
1. A dial depth gage
|
|
Height gages are normally graduated in which of the
following divisions? 1. .015 inch 2. .025 inch 3. .500 inch 4. .750 inch |
2. .025 inch
|
|
In reference to a surface plate, which of the following statements is/are true?
1. A surface plate provides a true, smooth, plane surface 2. A surface plate is often used as a level base for surface and height gages from which to make accurate measurements 3. A surface plate is usually made of close grained cast iron and is rectangular in shape 4. All of the above |
4. All of the above
|
|
In reference to ring gages, which of the following statements is true?
1. GO gages are larger than NO GO gages 2. GO gages are smaller than NO gages 3. GO and NO GO gages cannot be distinguished from each other 4. GO gages and NO Go gages are always the same size |
1. GO gages are larger than NO GO gages
|
|
Which of the following gage classes indicates that the gage is precision lapped to close tolerances?
1. Class Y 2. Class X 3. Class Z 4. Class ZZ |
2. Class X
|
|
Which of the following gage
classes is used only with ring gages? a). Class ZZ b). Class Y c). Class Z d). Class X |
a). Class ZZ
|
|
The plain snap gage is made in two general types. What are the types?
a). Flat and round b). Square and round c). Adjustable and nonadjustable d). Fixed and flexible |
c). Adjustable and nonadjustable
|
|
Before an adjustable snap gage can be used, which of the following procedures must be accomplished?
a). The gage must be heated to a predetermined temperature b). The GO and NO GO buttons, pins, or anvils must be set to the proper dimensions c). The gage must be cooled to below freezing d). The locking screw and the adjusting screws must be removed |
b). The GO and NO GO buttons, pins,
or anvils must be set to the proper dimensions |
|
Before using gage blocks, you should take which of the following actions?
a). Remove the coat of rust preventive compound from the gage blocks b). Boil the gage blocks in water c). Freeze the gage blocks d). Remove the adjusting screws from the gage blocks |
a). Remove the coat of rust
preventive compound from the gage blocks |
|
"Building gage blocks" is also known by which of the following terms?
a). Bonding them together b). Binding them together c). Wringing them together d). Bolting them together |
c). Wringing them together
|
|
Ordinary changes in temperature have a sizable effect on
measurements made with precision gage blocks. What is the standard measuring temperature? a). 50 degrees Fahrenheit b). 68 degrees Fahrenheit c). 68 degrees centigrade d). 72 degrees centigrade |
b). 68 degrees Fahrenheit
|
|
You should NOT leave gage blocks wrung together for long periods of time for which of the following reasons?
a). The surfaces will warp b). The surfaces will turn blue c). The surfaces will tend to corrode d). The ends will become unbalanced |
?
|
|
When using gage blocks, you must consider the source of error resulting from which of the following conditions?
a). Temperature b). Humidity c). Light d). Time |
a). Temperature
|
|
Gage blocks are used for which of the following purposes?
a). To test the outside air temperature b). To determine the humidity in a space c). To check the accuracy of tools, dies, and fixtures d). To test the strength of electrical wire |
c). To check the accuracy of tools, dies, and fixtures
|
|
Which of the following tools can be used to verify the accuracy and wear of ring and snap gages?
a). Gage blocks b). Climbing tools c). Awls d). Scribers |
a). Gage blocks
|
|
You should NEVER touch the measuring surfaces of gage blocks any more than necessary. The moisture from your hands contains an acid that can cause which of the following problems?
1. The gage blocks to warp 2. The gage blocks to stain 3. The gage blocks to attract an electrical charge 4. The gage blocks to become brittle |
2. The gage blocks to stain
|
|
After cleaning gage blocks, you should always take which of the following actions?
1. Coat the gage blocks with heavy grease 2. Boil the gage blocks in gasoline 3. Cover the gage blocks with a film of acid-free oil 4. Paint the gage blocks with lead-free paint |
3. Cover the gage blocks with a film of acid-free oil
|
|
Thickness gages are often referred to by which of the following terms?
1. Width gages 2. Height gages 3. Length gages 4. Feeler gages |
4. Feeler gages
|
|
Center gages are graduated in which of the following increments?
1. 14ths, 20ths, 24ths, and 32nds of an inch 2. 15ths, 22nds. 26ths, and 34ths of an inch 3. 17ths, 28ths, 30ths, and 36ths of an inch 4. 19ths, 25ths, 29ths, and 37ths of an inch |
1. 14ths, 20ths, 24ths, and 32nds of an inch
|
|
You can use a screw pitch gage to check the pitch of which of the following types of threads?
1. U. S. Standard and Metric 2. National Form and V-form 3. Whitworth cut 4. All of the above |
4. All of the above
|
|
The pitch of a screw thread is the distance between the center of one tooth to the
1. end of the screw 2. center of the next tooth 3. center of the screw head 4. head of the screw |
2. center of the next tooth
|
|
Telescoping gages are used for which of the following purposes?
1. To gage larger holes 2. To measure inside distances 3. Both 1 and 2 above 4. To measure |
3. Both 1 and 2 above
|
|
Telescoping gages normally have what maximum measuring capacity?
a. 3 inches b. 6 inches c. 8 inches d. 9 inches |
b. 6 inches
|
|
On a thread cutting tool gage, what do the numbers represent?
1. The number of threads per inch 2. The number of threads per foot 3. The number of threads on a screw or bolt 4. The length of a screw or bolt |
1. The number of threads per inch
|
|
Each blade of a fillet and radius gage is normally marked in which of the following increments?
a. 10ths b. 32nds c. 42nds d. 64ths |
d. 64ths
|
|
Which of the following tools is used to check the accuracy of drill cutting edges after grinding?
1. A marking gage 2. A thickness gage 3. A drill point gage 4. A rule depth gage |
3. A drill point gage
|
|
A wire gage is normally what shape?
1. Square 2. Triangular 3. Circular 4. Rectangular |
3. Circular
|
|
Drill gages have a series of holes. The holes are marked in which of the following ways?
1. Letters 2. Fractions 3. Numbers 4. All of the above |
1. Letters
|
|
Marking gages are normally made from which of the following materials?
1. Copper or tin 2. Wood or steel 3. Plastic or glass 4. Paper or plastic |
2. Wood or steel
|
|
Which of the following tools can be used to check the piston ring gap clearance in a cylinder bore?
1. A thickness gage 2. A marking gage 3. A wire gage 4. An awl |
1. A thickness gage
|
|
Which of the following types of pliers can be used to cut small materials such as wire and cotter pins?
1. Parallel jaw 2. Flat-nose 3. Slip-joint 4. Diagonal cutting |
4. Diagonal cutting
|
|
The piston holding vise is a special purpose vise which can hold engine pistons up to and including what maximum diameter?
1. 3 1/2 inches 2. 5 1/2 inches 3. 7 2/3 inches 4. 9 3/8 inches |
2. 5 1/2 inches
|
|
The pin vise is a special purpose vise which has a knurled metal handle and a chuck. It is designed to hold material from 0 to what maximum diameter?
1. 0.187 inch 2. 0.397 inch 3. 3.254 inches 4. 8.134 inches |
1. 0.187 inch
|
|
The handsaw filing vise is a special purpose vise used for
holding handsaws while they are being sharpened. It has jaws that are normally between 9 1/2 and what maximum number of inches? 1. 5 inches 2. 7 inches 3. 11 inches 4. 32 inches |
3. 11 inches
|
|
Which of the following types of pliers is used only for cutting?
a. Diagonal b. Slip-joint c. Round-nose d. Flat-nose |
a. Diagonal
|
|
The pin vise is a special purpose vise which has a knurled metal handle and a chuck. It is designed to hold material from 0 to what maximum diameter?
1. 0.187 inch 2. 0.397 inch 3. 3.254 inches 4. 8.134 inches |
1. 0.187 inch
|
|
The handsaw filing vise is a special purpose vise used for
holding handsaws while they are being sharpened. It has jaws that are normally between 9 1/2 and what maximum number of inches? 1. 5 inches 2. 7 inches 3. 11 inches 4. 32 inches |
3. 11 inches
|
|
Which of the following tools are used to hold work that cannot be held in a vise, or that has to be held for extended periods of time?
1. C-clamps 2. Chisels 3. Calipers 4. Reamers |
1. C-clamps
|
|
In reference to hand screw clamps, which of the following statements is true?
1. A hand screw clamp usually is made up of three jaws 2. A hand screw clamp should be tightened with a wrench or bar 3. A hand screw clamp is used for holding wood while gluing 4. A hand screw clamp is available in one size only |
3. A hand screw clamp is used for holding wood while gluing
|
|
Jacks can be used for which of the following purposes?
1. For raising and lowering heavy loads 2. For spreading and clamping operations 3. For pushing and pulling operations 4. All of the above |
4. All of the above
|
|
Which of the following types of hammers is used for driving and pulling nails?
1. A carpenter's hammer 2. A ball peen hammer 3. A bumping body hammer 4. A cross peen hammer |
1. A carpenter's hammer
|
|
Hammers usually come in which of the following sizes?
a. 1, 2, 4, and 6 ounce sizes b. 2, 3, 6, and 9 ounce sizes c. 6, 9, 12, and 15 ounce sizes d. 7, 13, 16, and 20 ounce sizes |
d. 7, 13, 16, and 20 ounce sizes
|
|
Which of the following types of hammers is used for forming soft metal, peening rivet heads, and striking metal in out-of-the-way places?
1. A carpenter's hammer 2. A ball peen hammer 3. A claw hammer 4. A club hammer |
2. A ball peen hammer
|
|
Which of the following tools would normally be used for breaking stones and concrete?
1. A ball peen hammer 2. A bumping hammer 3. A blacksmith's hammer 4. A carpenter's mallet |
3. A blacksmith's hammer
|
|
An inserted soft-faced hammer that is extra hard will be what color?
1. Yellow 2. Green 3. Black 4. Red |
1. Yellow
|
|
Which of the following tools is used to form and shape sheet metal?
1. A carpenter's hammer 2. A tinner's mallet 3. A jeweler's hammer 4. A mason's hammer |
2. A tinner's mallet
|
|
A trimmer's hammer has a round flat face on one end of the head. What type of face is on the other end of the head?
1. A square flat face 2. A round pointed face 3. A tapered chisel face 4. A curved claw face |
3. A tapered chisel face
|
|
What are the four basic types of dead blow hammers currently in use?
1. Standard head, slimline head, sledge, and ball peen 2. Round head, streamline neck, curved back, and rivet face 3. Huge, large, medium, and small 4. Ball peen, curved back, rivet face, and round head |
1. Standard head, slimline head, sledge, and ball peen
|
|
Which of the following types of mallets is made by tightly wrapping and staking a sheet of leather?
1. A carpenter's mallet 2. A rubber mallet 3. A tinner's mallet 4. A rawhide mallet |
4. A rawhide mallet
|
|
Cross-point screwdrivers normally come in which of the following sizes?
1. 2 to 4 inch sizes 2. 3 t o 8 inch sizes 3. 4 t o 12 inch sizes 4. 9 t o 16 inch sizes |
2. 3 t o 8 inch sizes
|
|
Which of the following types of screwdrivers should you use to drive or remove screws that cannot be lined up straight with common screwdrivers, or are located in tight corners?
1. Cross-point 2. Cross-tip 3. Ratchet 4. Offset |
4. Offset
|
|
Which of the following tools is used to make a pilot hole in wood for wood screws?
1. A cross-point screwdriver 2. A flexible screwdriver 3. A screw starter or gimlet 4. A two-piece collet die |
3. A screw starter or gimlet
|
|
Which of the following types of drills is made up of a head, crank, crank handle, ratchet mechanism, and chuck?
1. A hand drill 2. A breast drill 3. A brace drill 4. An electric drill |
3. A brace drill
|
|
Which of the following tools are used to remove broken screws without damaging the threads or surrounding material?
1. Scew extractors 2. Plumb bobs 3. Chisels 4. Scribers |
1. Scew extractors
|
|
Which of the following types of wrenches has a long smooth shank providing the user with a better gripping surface and is used to reach behind or below blind surfaces?
1. A box wrench 2. A plug wrench 3. A torque wrench 4. An engineer's single open-end wrench |
4. An engineer's single open-end
wrench |
|
Box wrenches surround the nuts. bolt heads, or studs on all sides. They are available with which of the following point openings?
1. 6-point openings 2. 12-point openings 3. Both 1 and 2 above 4. 29-point openings |
3. Both 1 and 2 above
|