Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
130 Cards in this Set
- Front
- Back
- 3rd side (hint)
|
What switch/switches do you press to override #2/#3 hydraulic aux pumps for an auto shutdown due to low quantity or overheat? |
Press and hold appropriate aux pump switch for 5 seconds |
|
|
|
What won’t be available during the Alert start feature until the battery bus is powered? |
Fire detection or protection |
|
|
|
Battery Direct Bus, Battery bus, AC/DC emergency buses, AC/DC transfer buses compromise the what? |
Emergency power system |
|
|
|
To preclude damage to the landing gear, accomplish no more than how many consecutive landings without a cooling period? |
4 |
|
|
|
How do you determine an aircrafts maximum payload? |
Subtract operating weight from zero fuel weight |
|
|
|
Following a intentional cabin depressurization above 10k ft, what must the internal cabin be pressurized to in order to reset the regulators? |
3,500 |
|
|
|
Below what cabin altitude must the oxygen regulators be manually positioned to ON to ensure oxygen is provided to passengers? |
12,500 |
|
|
|
How do you operate the -1 Emergency Oxygen Regulator? |
Clockwise; 6 seconds |
Spring loaded surge knob/hold momentarily |
|
|
If either the pilots or loadmasters FED ARM switch is in the arm, what panels can fire all 4 FEDS hatches? |
Maintinance ditching hatch/FWD LM station |
|
|
|
How many/where are the fire extinguishers located? |
2 cockpit, 1 crew rest, 6 cargo compartment |
|
|
|
What is the EEBD and how many do we have? |
15 minute self contained breathing system, 6 on aircraft |
|
|
|
How can you get coms when the aircraft is powered by batteries alone and the pilots CNC indicates off? |
Using the UHF/VHF backup control panel and COMM 1 |
|
|
|
When is the only time the LM advises the medical crew that seatbelts are required? |
Immediately prior to takeoff |
|
|
|
Except during preflights and when the mask is in use where smoke/fumes is not present, what position can the purge valve be in? |
Open |
|
|
|
How do you open troops doors in flight? |
Deploy deflector 10-15 degrees initially before door opening |
|
|
|
During on/off loading, what must you not do to pneumatic tires? |
Deflate tire past rated pressure |
|
|
|
Single anxle loaded equipment with its tounge resting on the floor, will be what? |
Drained |
|
|
|
What must you do when a vehicle is parked on the cargo floor and parking brakes are inoperative? |
Minimum 2 chains/devices; 1 FwD/ 1AFT |
|
|
|
Up to what weight limit may you remove a inner roller channel from the ramp toes when bare tine forklifting? |
8,500 |
|
|
|
Except when prohibited by specific procedures, what may you reset open circuit breakers? |
Once; when electrical condition was transient in nature |
|
|
|
If both your left and right Shielded Mild Detonating Cords (SMCD) are in operative, how many people are limited to over water flights? |
92 |
|
|
|
What’s the signal for prepare for ditching/crash landing |
6 short rings of alarm bell |
|
|
|
All odors not identified by crew should be considered toxic, what must you do? |
Refer immediately to Fire and Smoke; Smoke, Fire, or Fumes procedures |
|
|
|
What is the loadmaster at minimum required to provide when ditching is imminent? |
First aid kit/Flashlight |
|
|
|
If a fire is being fed by an oxygen system, what must you do until the fire is suppressed? |
Turn off manual shut off valves |
|
|
|
When lowering gear for an emergency checklist, what gear must be lowered first on the main landing gear system? |
Forward gear first |
|
|
|
What’s the maximum vertical height of a platform to be jettisoned from the aircraft and where is it measured from? |
118; Top of platform |
|
|
|
When jettisoning cargo, what must you do before stating “Locks Released” |
Ensure all selected lock annunciators are blank |
|
|
|
During a ditching incident, what must you no do prior to the aircraft coming to a complete stop and ensuring life rafts are not lost? |
Do not activate FEDS hatches |
|
|
|
During a ditching incident, what must you no do prior to the aircraft coming to a complete stop and ensuring life rafts are not lost? |
Do not activate FEDS hatches |
|
|
|
What’s the maximum lateral loading limitation of the cargo compartment? |
93,000 |
|
|
|
Don’t use what cargo compartment lighting in flight? As it will disable many features |
SECURE |
|
|
|
During ambient temperatures, how many times can you cycle the hydraulic aux pumps? |
Max of 10 |
|
|
|
How many serviceable floor attachment fittings are required to secure the centerline seats? |
4 |
|
|
|
If cargo/equipment is non-standard and presented for airlift, and not accompanied by an ATTLA, what do you do? |
May be loaded provided they do not exceed limitations/procedures in the -9 |
|
|
|
A vehicle single axle must be loaded within 8in of centerline in Compartment D/F/G if the weight exceeds what? |
22001-27000 |
|
|
|
A vehicles single axle must be loaded within 8in of centerline in compartment E if the weight exceeds what? |
27001-36000 |
|
|
|
What’s the max weight of a tracked vehicle with articulated suspension in compartment E? |
130,000lbs |
|
|
|
tracked vehicles with articulated suspension and wheel weights exceeding what... must be loaded within 8in of centerline |
5,000lbs |
|
|
|
Tunner loaded furnished bridge plates shall not be used when loading/off-loading rolling stock from a K-loader with the ramp toes installed |
True |
|
|
|
Hazardous cargo considered jettison-able _______ be positioned forward of non-jettison-able cargo except whe its size, weight, and location will permit jettison by hand. |
Shall Not |
|
|
|
What highlights essential operating procedures, practice, and condition or statement, etc. which if not strictly observed could result in damage to, or destruction of equipment or loss of mission effectiveness? |
Cautions |
|
|
|
If cargo projects aft of the end of the logistic rails, at what FS must you make sure the ramp toes do not contact the cargo while being raised to the vertical position? |
FS 1390 |
|
|
|
What is the required persists shoring for the RAMP GROUND SUPPORT pad? |
18in/30in |
|
|
|
Aft end of the ramp toes will not be supported in what position? |
Low |
|
|
|
Aft end of the ramp toes will not be supported in what position? |
Low |
|
|
|
What is the single line winching limitation while winching a vehicle up a 15 degree incline with pneumatic tires? |
20,000lbs |
|
|
|
What position will the toes be in during flight? |
Stowed on cargo door or Raised to the vertical position |
|
|
|
When winching and direction of pull is changed, what must you do to the sheave? |
Be manually realigned to the new direction of pull |
|
|
|
Palletized seat assemblies may be loaded in the logistic rails when transported as cargo. Passengers will not occupy palletized seats in logistic rails. |
True |
|
|
|
On AE missions, what is the ramp restricted too? |
Two pallets in ADS or floor loaded cargo centerline |
|
|
|
Max weight of pallet/pallet train loaded in logistics with one lock engaged left/right is good up to what weight? |
10,355 |
|
|
|
What is loadable ramp hinge height? And what is the loadable height at the aft of the ramp? |
156in hinge/116in aft of ramp |
|
|
|
When/where are spotters required to observe clearance of the wing box? |
148in/FS 937 |
|
|
|
What is the rule when loading ISU containers that are 90 inches or higher into the logistic rails on the aircraft ramp? |
Ramp toes with rollers and guide rails SHALL be installed |
|
|
|
Primary method of loading pallets into the ADS/logistic rails are using the the ramp toes |
True i |
|
|
|
If these are not used.... both 40k and 20k Ramirez K-Loadeds have to be backed in when preparing to load/unload cargo into the logistic rail system |
Ramp toes |
|
|
|
Required restraint for cargo on the pallet/pallet train shall be provided using nets, tiedown straps, or chains. When supplemental restraint is required, additional tiedowns may be attached to the pallet or cargo floor |
True |
|
|
|
Straps and chains shall not be mixed to restrain cargo in the same direction. However, 10k and 25k rated devices with the appropriate chains may be used for a given direction of restraint |
True |
|
|
|
At what weight must netted two pallet trains be secured to the floor? |
Anything above 20,710 |
|
|
|
Pallets/pallet trains up to 7,800 per pallet may be loaded into the ADS rail/lock system provided what? |
At least one lock left and one lock right are engaged in the pallet |
|
|
|
What direction must ensure cargo on the ramp is restrained for before closing the ramp/door? |
Forward and aft |
|
|
|
Netted pallets not to exceed 96in can weigh up to what? |
10,000 |
|
|
|
What is the maximum wheel load on each ramp toe in the low position? |
5,000lba |
|
|
|
Maximum pallet/platform weight on two ramp toes? (Except for 18-foot type VI platforms which may weigh up to 14,500) |
10,355 |
|
|
|
Vehicles with transmissions that are not equipped with a neutral position shall be offloaded/loaded using the cargo winch. |
False |
|
|
|
Maximum single axle load in the low position? |
10,355 |
|
|
|
Netted pallet trains secured with nets shall not exceed what weight? |
26,000 |
|
|
|
Netted pallet trains over 96inches talk but not to exceed 100inches secured with nets shall not exceed what weight? |
21,000 |
|
|
|
Winching in the cargo compartment must be monitored by how many people? |
3 personnel |
|
|
|
Winching in the cargo compartment must be monitored by how many people? |
3 personnel |
|
|
|
Low profile cargo limitations? |
45inches/2,500lbs |
|
|
|
What are plywood pallet/chain bridle limitations? |
30inches;2 bridles; 3/4in thick |
|
|
|
What stowage pins, if not installed correctly, may come loose during flight? |
Lower; both left and right |
|
|
|
While positioning pallets/platforms for loading into the logistic rails, if not carefully monitored, MHE may contact the what? |
Strakes |
|
|
|
While traversing the ramp hinge in a winching operation, it may be necessary for you to do this in order to keep constant tension on the winch cable? |
Push |
|
|
|
How many empty pallets may be stacked on each other for airlift excluding the base pallet? |
20 |
|
|
|
During palletized cargo loading limitations, the minimum distance between the K-loader d the ramp toes shall be what? |
4inches |
|
|
|
Damage may occur if cargo tiedown that spans the ramp from the main floor is not sufficiently slackened or what? |
Removed |
|
|
|
Minimum thickness of roller shoring? |
1/2inch |
|
|
|
What is the required overlap between the ramp toe contact pads and the floor of the loader with the toes in the high position? |
11inches |
|
|
|
In the high position the ramp toes should be at an angle which causes the aft end of the toes to be above the coplanar position with the ramp floor. |
False |
|
|
|
How many CGU-1/B straps can fit on 1 tie down ring? |
5 straps |
|
|
|
When attaching multiple devices to 1 ring, the ring can’t what? |
Be used for both forward and aft restraint |
|
|
|
To avoid slippage of the straps in the spool assembly, assure how many turns are ratcheted? |
1.5 turns |
|
|
|
When there’s multiple loads, to ensure good CRM, who is the overall responsibility for completion of checklists? |
Primary |
|
|
|
What will be worn at all times while crew members are operating at their primary duty station? |
Headsets; helmet |
|
|
|
Due to mission requirements, and at the discretion of the PIC, loadmasters may be asked to occupy a seat on the flight deck or in the cargo compartment |
True |
|
|
|
How many passengers may the c-17 carry without a baggage pallet? |
20 |
|
|
|
For planning purposes, how many people can be strapped to the floor and how many to the ramp? |
300 floor/ 50 ramp Depending on size of each person |
|
|
|
Maximum altitude for emergency airlift of personnel will not exceed what flight level? |
25,000 |
|
|
|
Who is the on-scene expert for load planning and accepting cargo for airlift? |
Loadmaster |
|
|
|
What smoke detectors are needed according to the MEL for home station departures? |
9; 10; 13; 14 |
|
|
|
What is maximum FDP for a basic crew? With auto pilot/without |
16hr/12hr |
|
|
|
Maximum CDT for basic crew? |
18hr |
|
|
|
Maximum CDT for augmented aircrew? |
24hr+45 |
|
|
|
Who is the waiver authority for all missions in regards to the MEL? |
WG/CC or equivalent, delegable no lower than OG/CC |
|
|
|
When are wing walkers required? |
25ft without but monitoring 10ft to avoid taxi obstructions |
|
|
|
While performing duties in the cargo compartment and movement is required during low level operations, what is required? |
Helmets |
|
|
|
A false/inaccurate reading may occur with the ADS rail locks if what happens before lock force pounds are set? |
Armed |
|
|
|
Depressurization checklists will be run prior to what? |
The slowdown checklist |
|
|
|
Cabin altitude checklist will be run prior to what? |
A cabin altitude exceeding 10,000ft MSL |
|
|
|
Depressurization checklist will be run prior to? |
Slowdown checklist |
|
|
|
Depressurization checklist will be run prior to? |
Slowdown checklist |
|
|
|
If the drogue chute does not deploy automatically or with the manual backup switch, the loadmaster will state what and complete the Heavy Equipment Malfunction checklist? |
MALFUNCTION |
|
|
|
Depressurization checklist will be run prior to? |
Slowdown checklist |
|
|
|
If the drogue chute does not deploy automatically or with the manual backup switch, the loadmaster will state what and complete the Heavy Equipment Malfunction checklist? |
MALFUNCTION |
|
|
|
If the TRM fails to release the extraction link (either manually or with backup switch) the loadmaster will state “MALFUNCTION” and activate the DROGUE JETTISON switch. If the drogue chute fails to jettison, loadmaster will what? |
Place the DROGUE JETTISON switch to the OFF position |
|
|
|
Depressurization checklist will be run prior to? |
Slowdown checklist |
|
|
|
If the drogue chute does not deploy automatically or with the manual backup switch, the loadmaster will state what and complete the Heavy Equipment Malfunction checklist? |
MALFUNCTION |
|
|
|
If the TRM fails to release the extraction link (either manually or with backup switch) the loadmaster will state “MALFUNCTION” and activate the DROGUE JETTISON switch. If the drogue chute fails to jettison, loadmaster will what? |
Place the DROGUE JETTISON switch to the OFF position |
|
|
|
If the extraction chutes have exited the aircraft and the platform fails to move, ensure ______ rotary switch is set to the lowest lock number setting engaged in that platform that failed to move and activate the ________ switch |
ADS R LOCK SELECT; R LOCK GANG RELEASE switch |
|
|
|
Depressurization checklist will be run prior to? |
Slowdown checklist |
|
|
|
If the drogue chute does not deploy automatically or with the manual backup switch, the loadmaster will state what and complete the Heavy Equipment Malfunction checklist? |
MALFUNCTION |
|
|
|
If the TRM fails to release the extraction link (either manually or with backup switch) the loadmaster will state “MALFUNCTION” and activate the DROGUE JETTISON switch. If the drogue chute fails to jettison, loadmaster will what? |
Place the DROGUE JETTISON switch to the OFF position |
|
|
|
If the extraction chutes have exited the aircraft and the platform fails to move, ensure ______ rotary switch is set to the lowest lock number setting engaged in that platform that failed to move and activate the ________ switch |
ADS R LOCK SELECT; R LOCK GANG RELEASE switch |
|
|
|
Using the EFTC and multiple type 5 platforms, the c-17 has the capability to drop how much? |
110,000lbs |
|
|
|
Maximum dimensions of airdrop loads? |
118in high/126inches wide |
|
|
|
During a towed parachutist, the PF will avoid _____ as the parachutist may start swinging violently which will increase the possibility of injury |
Turn the aircraft in the direction of the towed parachutist |
|
|
|
During a towed parachutist, if the decision is to cut, who is responsible to cut the static line on the PF command? |
Loadmaster |
|
|
|
During a fouled parachutist retrieval, do not attempt to pull what through the spool assembly? |
D-bags |
|
|
|
During CDS Pre slow down, visual inspect what? |
The type 26 nylon hasn’t become entangled worth the GRMS |
|
|
|
What will the LM do if the load fails to release or stops moving aft? |
MALFUNCTION; attempt to secure any moving containers |
|
|
|
Soll II crew consist of who? |
LS, RS, JS, two Soll II LMs and a CST |
|
|
|
When conducting INfill/Exfill procedures with an actual upload, two Soll II loads are required. |
True |
|
|
|
Soll II event follows the same FDP/CDT guidance as a tactical event IAW with the Vol 3 |
True |
|
|
|
If time permits, give a PREPARE TO LAND advisory call on the PA system at what points? |
300ft but no later than 100ft to aircraft touchdown |
|
|
|
After final parking position ha been determined, during exfilltration static loading rehersal, where do you position the tape? |
Floor; sidewall |
|
|
|
What should be placed in the ring pan to indentify the tiedown ring being used for tiedown? |
Mini blue |
|
|
|
To aid in vehicle parking positions during blacked out on loads, what size should the tape be to identify the final spot? |
12-14 inches |
|
