Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
50 Cards in this Set
- Front
- Back
Who can supervise MRT Missle Reload? |
Certified Commissioned Officer, Warrant Officer, NCO (E6 or above) |
|
When operating the forklift, the automatic forklift level switch will be placed in the ______ position. |
Off |
|
The forklift operator can select one of three steering modes. What are they? |
2 wheel, 4 wheel, and Crab Wheel |
|
The Tilt Warning System will sound when the crane and vehicle are tilted to _____ degrees. |
5 Degrees |
|
How many times is a MRCTS test performed on a PAC-2 LS cable prior to hooking up to a missile canister? |
Two consecutive Pass, or Pass no-go Pass |
|
True or False. You are not required to turn on the Missile Heaters circuit breakers for the LS if you are operating in temperatures above 32°F. |
False |
|
True or false. The Patriot LS TM gives warnings on explosives to include the Missiles. |
True |
|
If the top corners of the Missile Canisters are painted with a 4-inch Yellow Square the Missile is a _______. |
Live Round |
|
True or False. If the wood runner on a missile canister has cracks that exceed five inches in length and extend completely through the runner, it is considered unserviceable. |
True |
|
What manual contains the steps and procedures for Missile Selectability? |
TM 9-1440-1600-10 |
|
True or False. PAC-2 / PAC-3 ELES launcher can be configured to fire both at the same time. |
False |
|
What does the acronym MRCTS stand for? |
Missile Round Cable Test Set |
|
True or False. The PAC-2 LS operator's manual has the meeting for the MRCTS failure codes. |
False |
|
What should you NOT do if a tipping condition is encountered with the GMT? |
Lower or extend the boom. As this will aggravate the condition. |
|
You are required to replace the GMT cable when you find _____ random distributed wires, or _____ broken wires and a strand. |
6 Random, 3 Broken |
|
What is the load rating on the GMT crane at maximum extension? |
4500 Pounds |
|
True or False. For the GMT crane, always wear protective gloves when handling winch wire ropes, and never operate a winch with less than 3 turns of a wire rope in the winch drum. |
False |
|
True or False. The Load Test due date and the Load Rating are not required to be stenciled on the GMT crane due to the fact you have Load Test paperwork on hand. |
False |
|
True or False. During the load test procedures for the GMT crane, you disengage the PTO and shut off the vehicle engine to test the crane for slippage. |
False |
|
How many, and at what locations on the GMT are the high idle switches located? |
3. Center Console, behind passenger in front of cargo hold, and Crain Controls |
|
What status code is used on the DA Form 5988-E of the GMT for a PTO light that is inoperable? |
( x ) Deadline |
|
For Forklift Reload Operations, the maximum capacity rating for the Forklift is? |
10,000 Pounds |
|
How many Soldiers are required to conduct Missile Reload Operations? |
5 |
|
Name all positions by CM# for forklift Reload. |
CM1: CM1 CM2: CM2 CM3: Saftey CM4: Operator CM5: Signal |
|
The Missile Tie Down Bolts are torqued to what foot pounds? |
60 ft/lbs (Foot Pounds) |
|
During Tactical Operations, before approaching the LS you must get permission from? |
The ECS |
|
During Forklift Missile Reload, the forks must extend no further than _____ inches past the Missile prior to lifting. |
6 Inches |
|
Hearing protection is required within ______ meters of the LS. |
10 Meters |
|
What Gunnery table is Crew Forklift and GMT Missile Reload conducted? |
Table V |
|
Define the terms Centralized and Decentralized reload in your own words. |
Centralized Reload refers to a predetermined reload area (i.e. an MSA), where you bring the launching station to the site. Decentralized reload occurs in a tactical deployment position, where in LS is emplaced. |
|
True or False. The launcher enable/Disable switch is set to disable to prevent inadvertent launch command signals from the ECS when electrical power is applied. |
True |
|
True or false. CM1 and CM2 may underground expended canisters prior to emplacing the GMT. |
False |
|
What is the minimum size area do you need during GMT Missile Reload. |
20 x 25 Meters |
|
True or False. The maximum stacking height for Patriot Missile Canisters in an MSA is four. |
True |
|
What color are the 4 inch square markings on top left front, and top right rear corners of the Patriot missile canister for a Missile Round Trainer (Dummy Canister). |
Bronze |
|
True or False. Patriot Missiles must be grounded when stored in a wooden or open storage magazine. |
True |
|
What color is marked in 4 inch squares on the top left front, and top right rear corners of the Patriot missile canister for a live missile? |
Yellow |
|
What is the minimum safe distance from a damaged Canisters with a live Missile Round? |
1250 Feet / 381 Meters |
|
What is the status code you use for a Quick-Release Plunger (Torque Tube Handle) that is broken or missing? |
( x ) Deadline |
|
What size socket is used to tighten the Torque Tie-Down bolts on the Patriot Missile Canisters? |
3/4 Inch Deep Well |
|
What are the 3 LS/GMT reload positions? |
Parallel, Perpendicular, and End-to-End |
|
The maximum number of expended canisters can be moved at one time with a GMT is ______ . |
2 Expended Canisters |
|
Who is responsible for the PMCS of the beam during GMT Missile reload? |
CM3 (Safety) |
|
The maximum allowable slope for a GMT Missile Reload, front to back and side to side, is how many degrees? |
10 Degrees |
|
How many fire extinguishers are required to perform a Reload Operation? |
4 |
|
If the GMT Crane Operator loses sight of the Signal, what should the operator do? |
Cease operations until visibility is restored |
|
How often is the GMT load tested? |
Every 12 Months |
|
A GMT Missile Reload crew has _____ minutes to conduct Missile Reload. |
60 Minutes |
|
True or False. 'Stray/No voltage tests' are conducted prior to the 'test launch' test on ELES. |
True |
|
Beam inspection criteria can be found in what manual? |
TC 44-635-14 |