Maine Inspection Manual Quiz

Front 1

Class A Inspection weight?

-extended?

Back 1

10,000 lbs or less

- if accommodated, & w/o air brakes, 10,001-26,000 lbs.

Front 2

Class B is?

CLass C?

Back 2

B is School Bus

-C is Motorcyle

Front 3

Class D weight(s)?

-# passengers?

Back 3

All vehicles over 26,001, except School

- between 10,001-26,000.

-more than 15 passengers

Front 4

-Exclusively inspect trailers and semi­trailers ?

Back 4

must be primarily engaged in the sale and/or service of trailers and semi­trailers, and may only purchase Trailer stickers.

Front 5

Classe E: vehicle year determined by?

-Vehicles manufactured before ______ are not subject to the enhanced inspection requirements.

Back 5

Chassis

-1974

Front 6

Gasoline powered vehicles manufactured during or after _____ and registered in Cumberland County shall be subject to a gascap pressure test.

Back 6

1974

Front 7

Vehicles manufactured during or after _____ and registered in Cumberland County are subject to both the gas cap pressure test and the on­board diagnostic test

Back 7

1996

Front 8

If there is a mistake in the VIN on the registration.....

Back 8

complete form MV­141 and mail to the Maine Bureau of Motor Vehicles.

Front 9

Prior to engaging in motor vehicle inspections for a new employer, an Inspection Technician shall notify__________ of the change of place of employment.

Back 9

the State Police Inspection Unit

Front 10

During the term of licensure, an Inspection Technician must report to the State Police Inspection Unit any convictions for violating 29­A MRSA § 1768, any suspension of the Inspection Technician’s license to operate a motor vehicle, and any criminal convictions _______.

Back 10

Immediately

Front 11

Inspection station licensees should order at least a __________ of stickers per order.

Back 11

three­ month supply

Front 12

Completed stub sheets must be returned to the Maine State Police Inspection Unit office _________.

Back 12

within 30 days after the issuance of the last sticker on the sheet.

Front 13

. The Technician or Inspection Station Licensee shall immediately report the (sticker) lossor theft to____________.

Back 13

the Maine State Police Inspection Unit & the appropriate law enforcement agency.

Front 14

Trailer sticker: The completed sticker shall be placed on the _________.

Back 14

lower left lateral side of the trailer. The sticker must be readily visible to a person standing upright next to the trailer.

Front 15

An Inspection Technician license is valid for ________years from the date of issue.

Back 15

five

Front 16

An Inspection Station license is valid for ____years from January 1st of the year of issuance

Back 16

two

Front 17

A person may renew a license for up to _______ following the date of expiration

Back 17

180 days

Front 18

Reject vehicle if less than _____ of the total available pedal travel remains when the pedal is depressed under moderate foot pressure.

Back 18

1/3

Front 19

Reject vehicle if the brake lining is cracked to a depth in excess of _____ of the lining thickness.

Back 19

50%

Front 20

Reject vehicle if seat belts are not installed in ______and subsequent models and retractable seat belts are not installed and functioning in ______and subsequent models.

Back 20

1966, 1980

Front 21

The exhaust system includes the exhaust manifold...... _________________.

Back 21

the piping leading from the flange at the exhaust manifold to and including the mufflers, the tail piping, and the catalytic converter.

Front 22

Reject vehicle if it was manufactured after the _______model years and it is not equipped with a catalytic converter.

Back 22

1982

Front 23

Reject vehicle if it is not equipped with approved safety glass wherever glass is used in doors, windows, and windshields, if the vehicle was manufactured after December 31, _______.

Back 23

1937

Front 24

Reject vehicle if cloudiness extends more than ______ from the top or sides or more than ______ from the bottom edge of the windshield.

Back 24

1 inch, 4 inches

Front 25

Reject vehicle if, in the critical vision area of the windshield,there are any un­repaired bull’s eye fractures, star fractures, stone bruises, cracks or chips that measure more than _____ at the extreme edges.

Back 25

½ inch

Front 26

Reject vehicle if there is any crack more than ______ long in the windshield.

Reject vehicle if there is a windshield wiper scratch, mar or marks more than 4 inches long and _______ wide on the windshield.

Back 26

4 inches, 1/8 inch

Front 27

Reject vehicle if any mirror does not give the driver a view ofthe road________ to the rear.

Back 27

200 feet

Front 28

Reject vehicle if a headlamp, measured from its center, is located less than________ or more than _________ above the level surface on which the vehicle stands.

Back 28

22 inches, 54 inches

Front 29

Reject vehicle if any tail light bulb does not produce sufficient light so as to be visible from a distance of ______ to the rear.

Plate lights:

Back 29

100 feet , 50 ft

Front 30

Ball joints with wear indicators(generally found on ______and subsequent models of vehicles) must be inspected with the ball joints loaded.

Back 30

1973

Front 31

Shock absorbers in satisfactory condition should not have more than ____cycles of free rocking motion.

Back 31

two

Front 32

Frame hights:

Vehicles up to and including 4,500 lbs GVWR Vehicles from 4,501 lbs. to 7,501 lbs. GVWR Vehicles from 7,501 lbs. to 10,000 lbs. GVWR

Back 32

front 24 inches, rear 26 inches,

front 27 inches, rear 29 inches,

front 28 inches, rear 30 inches

Front 33

Reject vehicle if the minimum frame end height is less than ___________.

Back 33

10 inches

Front 34

Reject vehicle if any tire has tread cuts or snags in excess of ________in any direction or a cut deep enough to expose the tire cords.

Back 34

1 inch

Front 35

Body lifts may not use more than a ________spacer.

Back 35

three inch

Front 36

Custom vehicle: The scrub line of the vehicle shall not be lower than _____ from a level surface.

Back 36

three (3) inches

Front 37

Frame height: Measurements must be taken from a level surface to the.......

Back 37

bottom edge of the original manufacturer’s frame rail. The frame rail must be measured at the end where the bumper brackets attach.

Front 38

Custom Vehicles: The vertical height of the windshield must be at least _________.

Back 38

7 inches