Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
37 Cards in this Set
- Front
- Back
What part and section of occupational health and safety code describes the membership of a joint worksite health and safety program |
Part 13 section 197 |
|
What part and section of occupational health and safety code describes the requirements and options for protective Footwear |
Part 18 section 233 |
|
What part and section of occupational health and safety code describes requirements for a worker training about WHMIS |
Part 29 section 397 |
|
What are the first aid requirements for low Hazard work at a close worksite with 5 to 9 workers at the work site for shift |
One emergency first aider, one standard first aider, number to first aid kit |
|
What is an employer's responsibility with regard to hazard assessment at a work site |
To develop a plan to eliminate or control any hazards identified at the worksite |
|
How is the Workers Compensation Board of Alberta funded |
100% of the funding for workers compensation comes from Employers in Alberta |
|
What are the four categories of workplace hazards |
Biological, chemical, ergonomic, and physical |
|
What is an example of an engineering control for work protection |
Isolation |
|
When is Administrative control put into place for worker protection |
When an engineering control cannot eliminate or control a hazard |
|
Who is responsible to have an emergency response plan in the workplace at the work site |
Employers |
|
What part of the occupational health and safety code covers the first Aid requirement at the worksite |
Part 11 |
|
What must your employer do if first aid supplies are stored in a secure container at a work site |
Ensure the containers are clearly marked to indicate their content |
|
What is the duty to use personal protective equipment according to the Alberta occupation health and safety Code |
What you and your employer must do if a hazard assessment identifies the need for the use of PPE |
|
Who is responsible to ensure worksite emergency response plan remain up-to-date |
The employees |
|
When a works cited hazard assessment identifies the workers are required to wear PPE what is your employer's responsibility |
Ensure all workers properly use and wear required PPE |
|
What is an employee responsibilities with regard to the use of PPE |
To inspect your PPE prior to each use |
|
Industrial headwear must comply with what |
CSA |
|
What is not an obligation your employer assumes when a hazard assessment indicates the need for PPE |
To post a duty to use personal protective equipment sign at all entrances to the worksite |
|
What is the characteristic of protective Footwear with a yellow triangle on the other side of the tongue of the right shoe |
Souls that provide electrical shock protection and a grade 2 protective toe will withstand impact up to 90 joules |
|
In what situation is your employer obligated to provide you with proper PPE according to occupational health and safety |
When workers are exposed to respiratory Hazard or excessive noise levels |
|
What standard must a full body harness meat if manufactured on or after July 1st 2009 |
CSA |
|
How often must you inspect your fall arrest equipment |
Before use on each shift |
|
What is the minimum distance ladder must protrude above the intended Landing point |
1 metre or 3 feet |
|
The safety factor for a scaffold must be designed and constructed to support at least |
4 times the load that may be imposed on it |
|
At what height must an employer have a guardrail erected for a temporary work area |
3M or 10ft |
|
When conducting a hazard assessment related to lifting and handling a load your employer must consider the |
Weight size and shape of the load |
|
What is not an example of a recommended lifting technique |
Lyft no higher than eye level |
|
What is the goal of proper lifting technique |
To eliminate bloating stress on the soft tissue of your lower back |
|
How is a safe working load swl defined |
Breaking strength divided bye the safety Factor |
|
What does the term shock load mean when applied to rigging equipment |
The sling is exposed to stress by having the load suddenly started or stopped |
|
What is the rigging factor or safety is to be used when lifting and transporting workers |
10 to 1 |
|
How often must rigging be inspected |
At the beginning of each work shift |
|
What is the recommended sling angle when rigging a |
The sling angle must never be less than 60% |
|
Who is responsible for providing workers with WHMIS training |
The employer must provide the training |
|
Employers are responsible to |
Provide an MSDS for each control product used in the workplace, inform all workers about chemical hazards at the work site, train workers about labels, MSDS and other identifiers |
|
Suppliers of Controlled Products are responsible to |
Provide MSDS for Controlled Products they sell or Import |
|
With WHMIS, Employees are responsible to |
Apply workplace labels where and when required |