Reading...
Play button
Play button
Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
82 Cards in this Set
- Front
- Back
|
How shold you lift a soft top HMMVW?
|
Use 5 ton vehicle sling w/3FT extension. Remove last 2 bars on back of canopy to avoid crushing.
|
|
|
What should you use to lift cars, vans and trucks?
|
5 ton vehicle slings w/17 ton wheel nets
|
|
|
How would you lift a M1A1tank and how much does it weigh?
|
Use 36 ton caldwells or 2"20's. It weighs 56.25 LT
|
|
|
Where are the lifting points on an AAV and how would you lift it? How much does it weigh?
|
Lifting points are located at top of vehicle, one @ each corner ( like a cleat with a whole in the center). Lift w/ 1"20's with 7 ton cargo hooks or shackles. Weight: 44,100 - 51,500 lbs
|
|
|
How much does a kalamar weigh?
|
39 LT
|
|
|
How many E-stops does an average Hagglund crane have?
|
6
|
|
|
What lifting points would you use to lift lighterage on the MAERSK and on the WATERMAN?
|
MAERSK: PH 10's
WATERMAN: PH 11's |
|
|
What must be done prior to lifting an articulating vehicle?
|
Install the locking br - usually red!
|
|
|
What would you use to lift a 5 ton utility truck?
|
- If using belly bands, the straps fwd must not rest on air valve. Belly bands go between wheel axels.
- If using combo bands & 17 ton vehicle slings w/ 5 ft extenders, ensure dunnage is placed btwn. hood and strap. |
|
|
How do you lift a tractor trailor (5 ton tactical vehicle)?
|
30' Belly bands or 17 ton vehicle slings.
|
|
|
How do you lift a 7 ton utility vehicle?
|
1"20's and belly bands. - 1"20's up fwd (lifting pts on hood) an 30' belly band (aft btwn tires).
|
|
|
Bsic hold contents of the AMSEA
|
5 holds. Hold 1: Containers & ammo; hold 2: containers & ammo; hold 3: RTCH, tanks, HMMWV's and kalamar; hold 4: vehicles; hold 5: LVS/CLS
|
|
|
Basic hold contents of the WATERMAN
|
7 holds, but only 5 are being used! Hold 1: containers; holds 2 - 5: vehicles
|
|
|
Basic hold contents of the MAERSK
|
4 Holds. Hold 1: vehicles and breakbuld; holds 2 - 4: cehicles & containers. ALL HOLDS: VEHICLES AND BB
|
|
|
MAERSK: Crane characteristics
|
Ped 1: Tap series: 30 LT/60LT twinned
Ped 2: Tap series: 30 LT/60 LT twinned Ped 3: G series: 35 LT/70 LT twinned PED 2 & 3 WORK TOGETHER FOR QUAD LIFTS |
|
|
WATERMAN Crane characteristics
|
5 cranes all together.
Gantry Crane ( fwd): 30 tons Ped1: G series: 50 LT/100 LT twinned Ped 2: G series: 35 LT/70 LT twinned |
|
|
MAERSK: Ligherage and deck layout
|
SLWT: 1
LCM-8: 2 CSP: 3 CSPN: 5 Total containers: 383 (below deck: 296; above deck: 87 - 33 refrigerators) |
|
|
LCM-8 characteristics
|
Landing craft mechanized 8.
Hoisting weigth: 59 LT capacity: 60 tons dimensions: 41 X 16 |
|
|
What are the 5 methods for lifting a container?
|
1. 1"20's w/Cargo hooks
2. 1"20's w/shackles 3. 20' rectangular spreader bar w/ manual twist locks 4. jawbones and shackles 5. ROPCO hydraulic spreader bar |
|
|
WATERMAN lighterage and deck layout
|
SLWT: 1
LCM-8: 2 CSP: 4 CSPN: 6 placed athwardship ( prt - stbd) total containers: 581 ( 389 below deck; 192 above deck; 41 refrigerators) |
|
|
CSNP
|
Causeway section non-powered. RRDF - Roll on/Roll off Discharge Facility: 72 LT
Beach end: 67 LT |
|
|
CSP
|
Causeway section powered. Hoisting weight: 88 LT
Capacity: 90 tons |
|
|
SLWT
|
Side Loadable Warping Tug. Hoisting weigth: 97.2 LT
capacity: 35 tons |
|
|
5 steps of ORM
|
Decision making process:
1. Identify hazard 2. Assess hazard 3. Make Risk decision 4. Implement controls 5. Supervise |
|
|
AMSEA ligherage and deck layout
|
SLWT: 1
LCM-8: 2 CSP: 4 CSPN: 6 Hose reels: 3 : 13.5 LT H2O 22 LT fuel Total containers: 578 (457 below deck; 121 above deck (regrigerators) |
|
|
Hose Reel Assembly
|
H2O - 13.5 LT
Fuel - 22 LT Used to carry, deploy and retrieve 4 & 6 " buoyant hose line: 5000 FT of 6" fuel hose. Hose reels will only be lifted with suppied slings. |
|
|
Placement of forwrad hose reels on the AMSEA
|
Placed with motor facing forward for easy access
|
|
|
AMSEA: what is the weight of the E beam and where is it stowed? SWL of E beam
|
10.6 MT
stowed port side of hatch 3 SWL: 102 LT |
|
|
what is the only size shackle to lift the E-beam?
|
1"20's with 1 1/8" shackles
|
|
|
Which type of vehicles use locking safety pins?
|
Osculating or articulating safety pins used for RTCH, LVS, 10K and road compactor
|
|
|
What needs to be done to D-7 and D-8 bulldozers prior to lifting?
|
LIft the blades and place dunnage btwn tracks and lifting slings.
|
|
|
- How many ft are in 1 meter?
- What is a short ton? - What is a metric ton (MT)? - What is a long ton (LT)? |
- 3' 3"
- 2000 lbs (short) - 2204.5 lbs (metric) - 2240 lbs (long) 2880 measurement tons are expected to be moved daily |
|
|
What ships have Folding Metal Covers?
|
WATERMAN: back aft 4, 4R &5
MAERSK: Holds 1 - 4 |
|
|
What is a bridge lock used for?
|
To interlock containers
|
|
|
What is a pineapple?
|
A container locking device.
|
|
|
When and where can you use hydraulic spreader bars?
|
On an AMSEA class ship using the KALAMAR w/hydraulic spreader bars to assist in the on/off load of containers located under the wings in hold 2
|
|
|
What pub provides "blocking and bracing" guidelines?
|
NAVSEAOP 3221 Rev. 2
TM 55-607 (Army Field Manual) |
|
|
Where are the twinning blocks located on the WATERMAN?
|
1 -behind Ped 2 bedside entrace to midship hallway
2 - locaed stbd side of ped 2 |
|
|
What type of container spreader bars are there?
|
- manual
- hydraulic |
|
|
What must be done prior to lifting a RTCH?
|
- Set the parking brake
- check the locking pin - if necessary, remove top handler to decrease weight |
|
|
The load must be @ what rated capacity of the slings, so that the caldwells will lock in place?
|
10 % of the SWL of the Caldwells
|
|
|
What degree must the Caldwells be to obtain best performance?
|
30 - 60 degrees
|
|
|
Where are the twinning blocks located on the MAERSK?
|
1- portside of hatch 1/ped1
2 - stbd of ped 2 3 - port of ped 2 |
|
|
On the MAERSK, what must be done to the cranes in order to remove & restow hose reels on Hatch 4?
|
This is one of the hardest lifts, as you have to override the lower limits - 10%- of the boom. Use key to bypass the parking of the jib.
|
|
|
Where is the QUAD beam located on the MAERSK?
|
Top of ped 3
|
|
|
How do you remove a KALAMAR?
|
Kalamar is located in hold 3, but works in holds 1 & 2. Boom capacity 39LT in single considered CRITICAL lift. To lessen weight, remove top handler with 1"20's w/hooks after disconnected from kalamar. Use Kalamar's own slings to lift it out of the hold. Prior to lifting top handler, you must rmove the 20ft manual spreader bar!
|
|
|
Where are the twinning blocks located on an AMSEA?
|
1 - stbd of ped 1
2 - port of ped 2 btwn hatch 3 & 4 |
|
|
- Where is the KALAMAR located?
- What is the weigth of the KALAMAR? - What do you use to lift the KALAMAR? |
- Hold 3
- 39 LT - it's own slings |
|
|
AMSEA crane characteristics
|
5 cranes
Ped 1 : G series: 39 LT Ped 2: G series: 39 LT/78 LT twinned Ped 3: G series: 39 LT/78 LT twinned |
|
|
How many hatches are on an AMSEA class ship and how do you remove the covers?
|
5 hatches
Remove covers with 20' container spreader bar |
|
|
Where are CLS's located on an AMSEA?
|
Hold 5 - A deck
|
|
|
What is the MPF's timeline for complete offload in stream and pierside?
|
Instream: 7 days
piersiede: 4 days |
|
|
What is the time line of lighterage offload pierside on an AMSEA?
|
1 - 2 days
|
|
|
In port, what will be the last can to be brought onboard?
|
The HAZMAT can - must be located outside port & stbd to be easily jettison.ed
|
|
|
How many shackles are used to lift a LCM-8?
|
6 shackles - 4 fwd adn 2 aft
|
|
|
Are CSPNs lifted with PH 10's or PH 11's?
|
PH 11's on the AMSEA and WATERMAN
PH 10's on the MAERSK |
|
|
At what sea state would you secure MPF operations?
|
2.5 knots
|
|
|
How would you lift a SLWT?
|
Take off the doghouse and fold back teh A frame. Ensure that the anchor is clear, if not, lower it until it gains clearance.
|
|
|
What are the lifting methods for the hose reels?
|
Hose reels can be lifted in 3 different ways:
1. 1" 20's from padeyes on top corners 2. 1" 30's from padeyes on bottom corners 3. spreader bars provided with reels |
|
|
How many parts does the E-BEAM have? On what class ships is the E-beam located?
|
3 parts: Swivel, Beam and Hook.
On AMSEA class ships |
|
|
Which is the only command you cannot use when lifting lighterage off hatches 3 &4 until you're clear of the house?
|
BOOM UP! It would cause lighterage to swing and hit the crane house.
|
|
|
How do you know the LCM-8 is properly seated on skids?
|
When white marks are lined up on boat and structure.
|
|
|
In what order do tween deck hatches come off on a MAERSK?
|
FWD - MID - AFT
|
|
|
How do you lift a D7 & where are the lifting points?
|
1" 20's w/shackles or 15 ton caldwells in pairs
Lifting pts are located on the sides btwn the tracks |
|
|
What is used to lift a D8 dozer and where are the lifting pts?
|
1 " 20"s or 36 T caldwells in pairs.
Llifting points: 2 behind the cab on the rear & 2 fwd on the hood. |
|
|
Where can you find the lifting points for a vehicle?
|
On the DATA PLATE.
|
|
|
What must you do before entering a hold?
|
Make sure the hold is gas free and has proper ventilation.
|
|
|
What should you do one you're entering a hold?
|
Find at least 2 escape routes in case of fire or emergency.
|
|
|
What must you do to an ambulance type HMMWV prior to lifting?
|
The lifting shackles on the back bumper must be moved to the ends of the bumper, so that the slings can't crush the back or cause damage.
|
|
|
SMALL TOOL BOX CONTENTS
|
2 allen wrenches; 4 chisels cold; 2 boxes cotter pins; hacksaw blades; 4 hacksaw frames; 10 claw hammers; 8" pliers; marline spikes; 1/2"drive ratchets; 4 flathead srewdrivers; 4 philipshead screwdrivers; sockets: 3/4" - 1 1/4"; 12" crescent wrenches; 15" crescenet wrenches; 2 first aid kits
|
|
|
LARGE TOOL BOX CONTENTS
|
36" crow bars; 24" pipe wrenches; 36" pipe wrenches; handsaws, 8lb sledge hammers; 100' sizing wire; safety harnesses; dyna brakes; box of earplugs.
|
|
|
HATCH BOX CONTENTS
|
8 ton speedblocks; 13' ladders; 5' wrecking bars; comealongs; 21thread; 5gal water cooler; PPE (hardhats, gloves, safety vests);1" taglines
(150 ft); 3" taglines (150 ft); 20' belly bands; 30' belly bands; 15 & 36 ton caldwell slings; 5 & 7 ton vehicle slings; 3' extenders; cargo nets (14x14); shackles - 3/4 "to 2"; 7 & 11 ton hooks; 2 bullhorns; wheelnets: 5,17,30 tn; endless slings(blue, orange, black); chaffing gear; timerhooks, drum lifters;set of dog clamps; bowtie; 2 strap wrenches; 2 dead blows |
|
|
How would you lift a SLWT?
|
Take off the doghouse and fold back teh A frame. Ensure that the anchor is clear, if not, lower it until it gains clearance.
|
|
|
What are the lifting methods for the hose reels?
|
Hose reels can be lifted in 3 different ways:
1. 1" 20's from padeyes on top corners 2. 1" 30's from padeyes on bottom corners 3. spreader bars provided with reels |
|
|
How many parts does the E-BEAM have? On what class ships is the E-beam located?
|
3 parts: Swivel, Beam and Hook.
On AMSEA class ships |
|
|
Which is the only command you cannot use when lifting lighterage off hatches 3 &4 until you're clear of the house?
|
BOOM UP! It would cause lighterage to swing and hit the crane house.
|
|
|
How do you know the LCM-8 is properly seated on skids?
|
When white marks are lined up on boat and structure.
|
|
|
In what order do tween deck hatches come off on a MAERSK?
|
FWD - MID - AFT
|
|
|
How do you lift a D7 & where are the lifting points?
|
1" 20's w/shackles or 15 ton caldwells in pairs
Lifting pts are located on the sides btwn teh tracks |
|
|
What is used to lift a D8 dozer and where are the lifting pts?
|
1 " 20"s or 36 T caldwells in pairs.
Llifting points: 2 behind the cab on the rear & 2 fwd on the hood. |
|
|
Where can you find the lifting points for a vehicle?
|
On the DATA PLATE.
|
|
|
What must you do before entering a hold?
|
Make sure the hold is gas free and has proper ventilation.
|
