Emgineering Graphics I

Front 1

What is method of defining parts based on how they function?

Back 1

Geometric dimensioning and tolerancing

Front 2

What ae symbol for GDT shown in?

Back 2

Feature control frames

Front 3

With a shaft, what is the maximum material condition size allowed?

Back 3

Largest (tolerance)

Front 4

With an internal feature, such as a hole, what is the maximum feature size allowed?

Back 4

Smallest (tolerance)

Front 5

What is the term used in GDT to desribe how much a feature can deviate from:
-Ideal form
-Orientation
-Position
as it departs from maximum material condition?

Back 5

Envelope principle

Front 6

What is the opposite of least material condition?

Back 6

Maximum material condition

Front 7

What is a precise flat surface made from steel or granite and used as a base for inspection?

Back 7

Surface plate

Front 8

What is a hand-held instrument for measuring lengths and inside and outside diameters and depths?

Back 8

Height gauge

Front 9

What is a perfect plane, centerline or point?

Back 9

Datum

Front 10

What is the most important datum?

Back 10

The primary datum

Front 11

.







.

Back 11

Datum Feature

Front 12

.







.

Back 12

Concentricity

Front 13

.







.

Back 13

Circularity

Front 14

.







.

Back 14

MMC

Front 15

.







.

Back 15

LMC

Front 16

.







.

Back 16

Parallism

Front 17

.







.

Back 17

Flatness

Front 18

.







.

Back 18

Cylindercity

Front 19

.







.

Back 19

Between

Front 20

.







.

Back 20

Staightness

Front 21

.







.

Back 21

Profile line

Front 22

.







.

Back 22

Profile Surface

Front 23

.







.

Back 23

Position

Front 24

What is the largest allowable size of a feature, such as a shaft, added to the maximum allowed geometric distortion?

Back 24

Virtual condition

Front 25

What is using fixtures and devices to inspect parts?

Back 25

Functional gauge

Front 26

What is a mechanical fastener used to join together two or more parts?

Back 26

Threaded fasteners

Front 27

What is the top or peak of the screw thread?

Back 27

Crest

Front 28

What is the distance between the corresponding points on adjacent thread forms, measured parallel to the axis?

Back 28

Pitch

Front 29

What is the bottom of the screw thread?

Back 29

Root

Front 30

What is the average of the major and minor diameter on a screw?

Back 30

Pitch diameter

Front 31

What is the threaded representation most commonly used when drawing threaded fasteners?

Back 31

Simplified

Front 32

What is a dimensioned, multi-view drawing of a singe part?

Back 32

Detail drawing

Front 33

What is a complete set of standardized drawings specifying the manufacture and assembly of a product, based on design?

Back 33

Working drawings

Front 34

What shows standard parts in an assembly, such as threaded fasteners, bushings, and bearings?

Back 34

Assembly view

Front 35

What is every part in an assembly assigned?

Back 35

Part number

Front 36

What do dimensions that are not specially toleranced, use?

Back 36

General tolerance note

Front 37

What is a formal request for making changes to an engineering drawing?

Back 37

Engineering Change Order

Front 38

On a screw thread, what indicates its allowance or tolerance?

Back 38

Class

Front 39

.








.

Back 39

Fillet

Front 40

.









.

Back 40

Square Groove

Front 41

.









.

Back 41

Bevel Groove

Front 42

.









.

Back 42

Corner Flange

Front 43

.









.

Back 43

V Groove

Front 44

.









.

Back 44

U Groove

Front 45

.









.

Back 45

J Groove

Front 46

.







.

Back 46

Spot Weld