Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
52 Cards in this Set
- Front
- Back
- 3rd side (hint)
On a GFCI receptacle, the incoming power is connected to the line terminals |
True |
|
|
_____ are considered non-temperable and are used in new installations requiring fuses. |
Type S |
|
|
Schedule 40 nonmetallic conduit has a smaller outside diameter then schedule 80 rigid nonmetallic conduit |
False |
|
|
One a receptacle, the brass screw is used to terminate the ground conductor |
False |
|
|
The ____ is a scale of specified diameters and cross sections for wire sizing and is the standard wire sizing scale for the United States |
American wire gauge |
|
|
_____ The most often used type of over current protection device used in residential wiring |
Circuit breakers |
|
|
A low resistance path, which results in a high value of current that flows around, rather than through, a circuit is called a _____ circuit |
Short |
|
|
Which of the following switches has ON/OFF marked on the switch handle? |
Double-pole |
|
|
The ____ is an organization that develops electrical equipment standards that all member groups follow when designing and producing electrical equipment. |
National Electrical Manufacturers Association |
|
|
A switch that is used on 240-Volt circuits to control a load from one location is called a ____ |
Double-pole |
|
|
When nonmetallic device boxes that are 2- gang or more are used, the installed cable must be supported within _____ inches of the box |
12 |
|
|
CO/ALR marked on a receptacle indicates that ___ conductors may be terminated to it. |
Copper Copper-clad Aluminum Aluminum |
|
|
The following conductors is the largest? |
#8 AWG |
#8 AWG #10 AWG #12 AWG #14 AWG |
|
The NEC requires that rigid metallic conduit to be supported within ___ feet of each box and then no more than every ____ feet thereafter |
3,10 |
3,8 5,10 2,10 3,10 |
|
The Grounded conductor is terminated to the ___ terminal on a receptacle |
Silver |
|
|
Type ____ cable is used for underground installations of branch and feeder systems |
None of the above |
NM NM-B SE None of the above |
|
Type ____ cable is a three-conductor cable used for underground service entry installation |
USE |
|
|
The ____ Conductor is used as the grounded conductor and returns Current from the load back to the source |
White |
|
|
When using aluminum conductors, _____ size conductor must be used to carry the same amount of current as a copper conductor |
A larger |
|
|
The National Electric Code requires electric cable supported within _____ Inches on single-gang nonmetallic device boxes |
8 |
|
|
It is the _____ who has the job of approving the electrical materials |
Authority Having Jurisdiction |
|
|
And accidental connection of a “hot” conductor and a grounded piece of equipment or the grounded conductor is called a ____ |
Ground fault |
|
|
All ____ boxes must be accessible after they are installed. |
Junction |
|
|
Electricians usually referred to armored clad cable as _____ cable |
Bx |
|
|
A _____ Is an overcurrent device that opens a circuit when a fusible link is melted away by the extreme heat caused by an overcurrent. |
Fuse |
|
|
____ Devices are used when more than one device is needed at one location |
Combination |
|
|
_____ Fuses cannot be used in new installations. |
Edison |
|
|
A (n)_____ Is a point on the wiring system at which current is taken to supply equipment. |
Outlet |
|
|
_____ Is a measure of how much a fastener is being tightened and is measured in foot-pounds |
Torque |
|
|
The _____ Of a conductor refers to it ability to Carry Current |
Amps |
|
|
A ____ Made from non-conductive nylon or stainless steel, is used to pull wires or cables through electrical conduit |
Fish Tape |
|
|
A(n)_____ is usually 9” Long and is used to level or plumb conduit, equipment, and appliances. |
Torpedo |
|
|
A (n)_____ Is used to pull wires or cables through conduit and to pull cables in insulated walls |
Lines man Pliers |
|
|
A (n)_____ Used to cut holes in wall board for boxes and to put plaster and lath for box installation in remodeling work |
Keyhole saw |
|
|
______ Screwdrivers are used to remove and install screws limited working space and to tighten and loosen lugs in limited working space. |
Stubby |
|
|
_____ Used to cut cables, conductors, form large conductors, and to pull and hold conductors. |
Lineman Pliers |
|
|
_____are used to form small conductors, cut conductors, and to hold and pull conductors. |
Long-nosed pliers |
|
|
_____ are used to cut cables and conducters in a limited space. |
Diagonal pliers |
|
|
_____ Are used to strip insulation, crimp solderless connectors, cut and size conductors, and cut and thread small bolts. |
Multipurpose tool |
|
|
A _____ Is used to transfer location points from ceiling to floor and floor to ceiling and to plumb conduit equipment |
Plumb Bob |
|
|
Of the following is not a commonly used drill chuck size |
3/8 |
1/8” 1/4” 3/8” 1/2” |
|
Probably the most popular style of wire stripper used in residential wiring is the non-adjustable type, commonly called a (n)_____ |
T-stripper |
|
|
If a run of conduit is plumb, It is _____ to the floor. |
Perpendicular |
|
|
When using a sledgehammer to install a ground rod at least _____ feet of the rod must be in the ground |
8 Feet |
|
|
On Construction sites, all 125-volt power tools must be plugged into a(n)_____ |
GFCI |
|
|
To drill holes in the studs electricians generally use a _____ drill to make Drilling easier in the tight spaces between framing members. |
Right Angle |
|
|
_____ drills are used to drill holes in masonry or concrete walls and floors. |
Hammer |
|
|
Another name for a Skil saw is a _____ saw. |
Circular saw |
|
|
Another name for a “Sawzall” is a _____ saw. |
Reciprocating saw |
|
|
A _____ Is used to cut holes in metal boxes for installing cable or conduit |
Knockout punch |
|
|
An electricians Hammer has _____ claws . |
Long/straight |
|
|
A drill bit with a spiral cutting edge used to bore holes in wood is called a(n) _____ bit. |
Auger |
|