Cr 206 Sec 10-11

Front 1

How many pulls can you make with the Kansas Jack World Rack 4000?

Back 1

12

Front 2

The carriage will swivel in how many positions?

Back 2

9

Front 3

Where is the long "T" assembly placed?

Back 3

On the end of the vehicle with the most damage

Front 4

It is advisable to route anchor chains over ________ to obtain an anchoring direction that does not pull the vehicle downward.

Back 4

Stands

Front 5

When you use a tower extension, what is the pulling capacity reduced to?

Back 5

2 tons

Front 6

Maximum load on a __________ is 10 tons in any combination.

Back 6

crossmember

Front 7

At what height on the towers can you make a five-ton pull?

Back 7

Any height

Front 8

What are the torque specifications of unibody clamps?

Back 8

80 to 100 ft. lbs.

Front 9

The procedure for making pulls over five tons is the same up to five tons, except all:

Back 9

Chains must be doubled, including anchor chains

Front 10

Explain the procedures for using a snap block with a chain for down pulls.

Back 10

Run chain through the snap block and back to the tower to double capacity.

Front 11

Auto body and frame straightening systems are designed to operate under severe loads. Improper rigging, insecure anchor points, faulty or damaged chains, or equipment overloads can result in: (3)

Back 11

Property damage, personal injury, and possibly death.

Front 12

Do not stand in front of or behind the towers when:

Back 12

Making pulls

Front 13

_______ _______ will drastically reduce chain capacity.

Back 13

Chain twists

Front 14

What is the capacity of the power lift bar when retracted and extended?

Back 14

2 tons retracted, 1 ton extended

Front 15

When positioning the towers to make a pull with the lever in the raised position, move the carriage swivel _____ _______ to the center of the rack.

Back 15

90 degrees

Front 16

What are the three basic ways to anchor the vehicle on the rack?

Back 16

Towers, tie-downs, and unibody clamps

Front 17

Always make pulls with the vehicle suspension:

Back 17

Loaded

Front 18

What are the three different power ranges on the power post?

Back 18

5-ton, 10-ton, and 20-ton

Front 19

______ ______ displays targets that cannot be seen by the scanner.

Back 19

Scanner view

Front 20

_____ _____ _____ _____ displays reference hole dimension and the direction it faces.

Back 20

Point info dialog box

Front 21

_____-numbered targets are on the right side of the vehicle.

Back 21

Even

Front 22

How far apart are the body scanner hubs?

Back 22

750mm

Front 23

The length of the targets varies from _____ to _____.

Back 23

95mm to 510mm

Front 24

The hubs in the body scanner spit at approximately _____rpm.

Back 24

850

Front 25

There are _____ targets with the Genesis Electronic Measuring System.

Back 25

37

Front 26

Targets numbered ___, ___, and ___ are used only with the upper body bar assembly.

Back 26

43, 44, 45

Front 27

What does the title bar identify?

Back 27

Title of document or document bar

Front 28

The work station should be at what location around the vehicle?

Back 28

Left front

Front 29

How should the body scanner be positioned under the vehicle?

Back 29

Deck of frame machine in center section

Front 30

What information must be entered into the customer data entry dialog box?

Back 30

Customer, vehicle, and work order information

Front 31

When using the "zoom" to enlarge the vehicle graphic, the cursor changes to a ________ ______ after you select the percentage you need.

Back 31

Magnifying glass

Front 32

In the Genesis Electronic Measuring system, What is a window?

Back 32

A frame on your computer screen used for initial setup and changing user preferences for genesis.

Front 33

What is an icon?

Back 33

Small picture or symbol

Front 34

What is the function of an icon?

Back 34

It commands an action

Front 35

What is the purpose of a dialog box?

Back 35

It allows you to communicate with the computer

Front 36

Press the _____ to move the cursor from one field to the next?

Back 36

tab

Front 37

After base targets have placed, what color do they appear on the graphic?

Back 37

Red Circles

Front 38

Which targets establish the body zero line?

Back 38

The first right left pair of reference points entered.

Front 39

What is a three point measurement?

Back 39

uses only 3 base points

Front 40

When a control point is misaligned more than 50mm in length, width, or height, the target on the graphic will appear ________.

Back 40

green

Front 41

The _____ ____ is the dark colored bar at the top of the window that displays the title of the document or current window.

Back 41

Title Bar

Front 42

_____ _____ contain groups of command buttons that are located at the right side and the bottom of the Vehicle Measure window, and at different locations in the Customer Data Entry Window.

Back 42

Tool bars

Front 43

________ _____ is a framed box within a window that contains data entry fields and other controls to allow you to communicate with a computer program.

Back 43

Dialog box

Front 44

____ ____ moves the cursor from one text field to the next, or one line to the next line in a multi-line text field.

Back 44

Tab key

Front 45

______ _____ are used to place a target at a location where an attachment cannot be used.

Back 45

Target bases