Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
22 Cards in this Set
- Front
- Back
|
Why is there an increasing need for weld quality? a. safety b. economics c. less conservative design d. government regulations e. all of the above |
e. all of the above |
|
|
What AWS document describes the rules for the CWI certification program? a. AWS 5.5 b. AWS d1.1 c. AWS QC1 d. AWS 5.1 e. AWS 14.1 |
C. AWS QC1 |
|
|
Weld quality control should begin after welding has been initiated. a. true b. false |
b. false |
|
|
What are the three welding inspector certifications covered in AWS QC1? a. CAWI, CWI, BWI b. CWMI, CAWI, SCWI c. SCWI, CWI, ACWI d. levels I, II, and III e. none of the above |
b. CWMI, CAWI, SCWI |
|
|
What is generally considered to be the most important quality of a welding inspector?
a. graduation from a welding vocational program b. an engineering degree c. an associate's degree d. professional attitude e. hold a certified welder certificate |
d. professional attitude |
|
|
The vision requirements for a CWI are near vision acuity on:
a. Jaeger J1 at no less than 24in b. Jaeger J2 at not less than 12 in c. Jaeger J2 at no less than 12, with or without corrective lenses d. The inspector cannot wear glasses e. 20/20 vision |
c. Jaeger J2 at no less than 12, with or without corrective lenses |
|
|
The acronym KASH stands for: a. knowledge, attitude, skills and habits b. knowledge, application, skills and habits c. knowledge, attitude, skills and honesty d. knowledge, application, skills and honesty e. knowledge, attitude, sincerity and honesty |
a. knowledge, attitude, skills and habits |
|
|
The welding inspector should have a basic understanding of:
a. welding processes b. nondestructive testing methods c. A and B above d. codes and standards e. all of the above |
e. all of the above |
|
|
The term used to describe a delay in the production schedule to permit inspection is:
a. NDE b. hold point c. pre-inspection d. reference point e. arc strike |
b. hold point |
|
|
Inspection report corrections should be made by:
a. rewriting the entire report b. reporting the correction to the welding forman c. telling the welder what was done d. ignoring the original error e. single line out the error, correct the error, date, and initial. |
e. single line out the error, correct the error, date, and initial. |
|
|
A definition of ethics is:
a. using common sense and honesty b. living by the rules c. being fair and impartial d. basing decisions on facts e. all of the above |
e. all of the above |
|
|
For communications to be effective, it should form a "continuous loop".
a. true b. false |
a. true |
|
|
The welding inspector must often communicate with:
a. welders b. supervisors c. welding engineers d. members of management e. all of the above |
e. all of the above |
|
|
NDE personnel (other than CWIs) are typically certified to what document?
a. AWS QC1 b. AWS d1.1 c. API 1104 d. ASNT SNT-TC-1A e. cert not needed |
d. ASNT SNT-TC-1A |
|
|
You must have a high school diploma to become a CWI.
a. true b. false |
b. false |
|
|
The CWI exam has several parts; these are:
a. fundamentals, practical, code b. fundamentals, basic, code c. basic, vision test, fundamental d. code, vision test, practical e. none |
a. fundamentals, practical, code |
|
|
The CWI exam requires that the AWS d1.1 code be used for the open book code test.
a. true b. false |
b. false |
|
|
The CWI exam contains three parts.
a. true b. false |
a. true |
|
|
The title of AWS Standard A3.0 is:
a. filler metal specifications b. standard welding terms and definitions c. guide to CWI certifications d. requirement for CWI certifications e. none of the above |
b. standard welding terms and definitions |
|
|
API Standard 1104 covers the fabrication of cross-country bridges.
a. true b. false |
b. false |
|
|
Some of the approved codes/ standards for the open book portion of the CWI exam are AWS d1.1, API 1104, AWS d1.5, and AWS d15.1.
a. true b. false |
a. true |
|
|
Prior to starting a job assignment the welding inspector should determine: a. what code, standard, or specification applies. b. what inspections should be conducted c. when inspections should be conducted d. where records are maintained e. all of the above |
e. all of the above |
