Cdc Vol. 1 General Maintainence Information Ures

Front 1

Which functions form a maintenance group?

Back 1

Maintenance operations

Maintenance

Aircraft maintenance

QA

Front 2

Who monitors flying and maintenance schedules and maintains visibility of fleet health indicators?

Back 2

Maintenance Operations Center (MOC)

Front 3

When you are assigned to an equipment maintenance sqaudron as an engine troop, to what flight will you most likely be attached?

Back 3

Maintenance

Front 4

When you are assigned to an aircraft maintenance sqaudron as an engine troop, to what flight will you most likely be attached?

Back 4

Specialist

Front 5

What does the fifth position of the Air Force specialty code (AFSC) 3A652 represent?

Back 5

Specific AFSC

Front 6

What type of training is provided to help you learn the knowledge portion of your job?

Back 6

Career development course (CDC)

Front 7

How many months must you have in the Air Force before you may attend the Airman Leadership School (ALS)?

Back 7

48

Front 8

Which program's purpose is to ensure safe and healthy working conditions for all Air Force employees?

Back 8

Air Force Occupational Safety and Health (AFOSH)

Front 9

Air Force occupational safety and health (AFOSH) standards are located within Air Force publication series __

Back 9

91

Hint 9

##

Front 10

Which Air Force instruction defines quality maintenance and requires maintenance personnel to display integrity and comply with all written guidance? __-___

Back 10

21-101

Hint 10

##-###

Front 11

Prior to starting any maintenance on the aircraft, what can you do to ensure that it is safe to proceed?

Back 11

Check with other personnel working inside and outside the aircraft

Front 12

How far does a propeller's axis of rotation extend?

Back 12

10 ft to the front and 5 ft from the rear

Front 13

To avoid the engine exhaust blast, what is the maximum distance to the rear of the aircraft?

Back 13

200 ft

Hint 13

###

Front 14

When approaching or leaving a helicopter with the blades rotating, all personnel need to remain in full view of the _____

Back 14

Pilot

Hint 14

The person who creates work for us

Front 15

FOD is normally caused by ______

Back 15

People

Front 16

Toxic materials are easiest to get into the body and cause rapid toxic reactions when they are in the form of _____

Back 16

Gases

Front 17

Who is responsible for providing you with training on how to wear, use, and maintain personal protective equipment?

Back 17

Supervisor

Front 18

A common method for disposing of hazardous waste is ________

Back 18

Dilution

Front 19

For hazardous waste disposal, it is unlikely the Air Force can justify ____________

Back 19

Incineration

Front 20

A specialized function of supply mission is ________

Back 20

Disposal

Front 21

From what perspective does the Global Logistics Support Center (GLSC) manage supply?

Back 21

Weapons System

Front 22

What system has the purpose of establishing a firm control over assets to make sure they are repaired at base level or sent to a repair facility as fast as possible?

Back 22

Repair Cycle Support System

Front 23

Selected Equipment items, when returned to depot because of their design characteristics function of application, are predetermined to require ________

Back 23

Overhaul

Front 24

Which supply document provides a means for organizations to review all document numbers processed during the day by the Standard Base Supply System (SBSS)?

Back 24

Daily Document Register (D04)

Hint 24

*##

Front 25

How many priority systems does Base Supply use when responding to a customer's supply needs?

Back 25

2

Front 26

Which is a two-part form that is attached to items requiring maintenance shop processing?

Back 26

AFTO Form 350

Hint 26

AFTO FORM ###

Front 27

Which publication provides a block-by-block explanation of how to document the Air Force Technical Order (AFTO) Form 350 tag?

Back 27

TO 00-20-2

Hint 27

TO ##-##-#

Front 28

If you are temporary duty (TDY) and both the Integrated Maintenance Data Systems (IMDS) and Standard Base Supply System (SBSS) are NOT available, what form would you use to order an engine part?

Back 28

AF IMT 2005

Hint 28

AF IMT ####

Front 29

Serviceable items, when recieved from supply and ready to use, each have an attached Department of Defense (DD) Form ____

Back 29

1574

Hint 29

####

Front 30

What time compliance technical order (TCTO) category is issued to correct hazardous safety conditions that can result in a fatality or serious injury to personnel?

Back 30

Immediate action

Front 31

What time compliance technical order (TCTO) category has alternately spaced red diagonals and Xs bordering the first page?

Back 31

Urgent action

Front 32

Which technical order (TO) covers all information concerning the Air Force TO system?

Back 32

00-5-1

Hint 32

##-#-#

Front 33

Who originates technical orders?

Back 33

Equipment manufacturer

Front 34

Who makes sure the Air Force technical order (AFTO) information management tool (IMT) Form 22 is valid and warrants submission?

Back 34

Supervisor of initiator

Front 35

The primary goal of the engine trending and diagnostics (ET&D) program is to prevent or limit damage to turbine engines by...

Back 35

Early detection of performance degradation and/or failures

Front 36

Within the engine trending and diagnostics (ET&D) program, to whom do flight-line personnel transfer collected data for analysis?

Back 36

Base engine maintenance shop

Front 37

Centalized repair facilities (CRF) provide support for whom?

Back 37

War fighters

Front 38

What drives the creation of a centalized rotable pool (CRP)?

Back 38

Customer wait time and transportation constraints

Front 39

When a centralized repair facility (CRF) ships a replacement asset to a deployed unit, who is responsible for ensuring all appropriate documentation is completed?

Back 39

CRF Personnel

Front 40

Depot maintenance provides support to base-level technicians by...

Back 40

Providing technical assistance and performing repairs beyond their capability

Front 41

Depot level support includes depot field teams (DFT) and _ _ _

Back 41

Contract field teams (CFT)

Front 42

A primary objective of the engine reporting system is to...

Back 42

Maintain accurate and timely engine inventories

Front 43

For how many categories of reporting does the comprehensive engine management system (CEMS) establish and maintain records?

Back 43

2

Hint 43

#

Front 44

On which Air Force technical order (AFTO) form should you record the removal and replacement of engine accessories?

Back 44

95

Hint 44

##

Front 45

To document information concerning the status of engine time compliance technical orders (TCTO), use Air Force technical order (AFTO) Form __

Back 45

95

Hint 45

##

Front 46

What is the purpose of the Lead the Fleet/Pacer programs?

Back 46

Determine distress modes of an engine and its subsystems in the field

Front 47

What is not a Lead the Fleet/Pacer program objectives?

Back 47

Reducing customer wait time for serviceable assets

Front 48

Carrying a handtool in your pocket is potentially hazardous because it could cause ______ __ ___

Back 48

Injury to you

Front 49

You should wear eye protection when you work...

Back 49

With tools that may cause flying particles

Front 50

Which technical order (TO) covers calibration procedures for torque wrenches?

Back 50

33K6 series

Hint 50

##*# series

Front 51

If you must torque a sequence of three or more bolts,...

Back 51

Use a staggered sequence

Front 52

The length of a torque extension is determined by the distance between the center of the square drive and the center of the ________ _______

Back 52

Broached opening

Front 53

If you were tasked to measure the clearance between two surfaces, what type of gauge would you use?

Back 53

Thickness gauge

Front 54

The longest calibrated movement between the spindle and anvil of an outside micrometer is _ ____

Back 54

1 inch

Hint 54

# ****

Front 55

Where is the contact point on a dial indicator located?

Back 55

At the end of a pivoted lever

Front 56

What feature is common to all dial indicators?

Back 56

Ability to amplify movement greatly

Front 57

The Fluke 8025A multimeter control that is used to set the meter to check for alternating current (AC) and indirect current (DC) is the...

Back 57

Function selector rotary switch

Front 58

What is the maximum voltage that can be measured if the range button is set at 30 on the Fluke 8025A multimeter?

Back 58

32

Hint 58

##

Front 59

For a borescope inspection and for a maximum benefit, which is necessary for the inspector to have?

Back 59

Experience

Integrity

Ability

Front 60

A rigid borescope requires...

Back 60

A direct and lateral straight shot at the inspection area

Front 61

When operating a borescope, what part of the borescope illuminates the interior of the area you are inspecting?

Back 61

Distal tip light guides

Front 62

What factors are considered for borescope operator certification?

Back 62

Experience

Maturity

Rank

Front 63

What type of borescope misuse causes a poor field of view (black spots)?

Back 63

Application of lateral (pinching) pressure to the fiber bundle

Front 64

What type of bolt should be used where shearing stress occurs?

Back 64

Clevis

Front 65

Which nuts should never be used where the temperature exceeds 250℉?

Back 65

Nonmetallic self-locking nuts

Front 66

The shank of a screw is defined as the...

Back 66

Combination of the body and the threads

Front 67

What type of washer is used to prevent corrosion of dissimiliar metals?

Back 67

Plain

Front 68

What type of pin is used in joints that carry shear loads and where the absence of clearance is essential?

Back 68

Tapered

Front 69

When you are lock wiring two units together, the first unit holes should be between what o'clock positions?

Back 69

3 and 6 o'clock

Front 70

When lock wiring, how many twists per inch are required to produce the proper stiffness?

Back 70

8 to 10

Front 71

Why is it necessary to carefully remove support clamps when disconnecting tubes?

Back 71

Prevents nicking and scratching

Front 72

Why should dust caps be installed over tube ends rather than inside them?

Back 72

Avoids possibility of leaving caps installed

Front 73

Never use oil as an aid to installing what kind of hoses?

Back 73

Self-sealing

Front 74

What box in the AFTO Form 781H shows the highest symbol in the AFTO Form 781A's?

Back 74

Box 6

Front 75

What area of a Line Replacement Unit (LRU) is most susceptible to Electrostatic Discharge (ESD)?

Back 75

Pins

Front 76

What must be done to a component after removing it from the engine?

Back 76

Cap and plug all openings

Front 77

What is used to seal male flared-type fuel drain fittings on an engine being prepared for air shipment?

Back 77

Caps

Front 78

The requirements for storing engines in a metal container is to maintain ________ ________

Back 78

Nitrogen Pressure

Front 79

Which container does not require warehouse facilities?

Back 79

Fiberglass reinforced plastic

Front 80

To release the internal air pressure in shipping container/module, you must remove the...

Back 80

Filler valve on the front end of the container

Front 81

What color is a serviceable humidity indicator on shipping container?

Back 81

Blue

Front 82

What should you use to check for pressure leaks on an engine/module shipping container?

Back 82

A soap-water solution

Front 83

Prior to removing a shipping container lid, what warning must be observed?

Back 83

Release all pressure before removing lid

Front 84

How many pins secure the adapters to the shipping container support?

Back 84

4

Hint 84

#

Front 85

During the "over 180 days" preservation period, the fuel system is maintained full of ____

Back 85

MIL-L-6081(grade 1010)

Hint 85

MIL-L-#### (grade ####)

Front 86

To prepare the engine fuel system for service after depreservation, you must flush the system with ____

Back 86

Fuel

Front 87

When metal is attacked by chemical corrosion, it will start

Back 87

On the surface of the metal

Front 88

Which factor is important in causing corrosion?

Back 88

Water

Front 89

On the the personnel maintenance platforms, the purpose of the platform safety lockpins is to

Back 89

Prevent the platform from lowering while it is in use

Front 90

Which part of the Air Force technical order (AFTO) Form 244, Industrial/Support Equipment Record, may the AFTO Form 245, Industrial/Support Equipment Record (Continuous Sheet), be used for?

Back 90

V/5

Hint 90

*/#

Front 91

Which item is one that a storage time period must be assigned to ensure that it will perform satisfactorily over a specified period of time?

Back 91

Shelf-life

Hint 91

_____-____

Front 92

When a bench stock item has a type I shelf-life, it means the item...

Back 92

Has a definite nonextendible period of shelf-life

Front 93

In the case of a failure trend that may contribute to accidents, deficiency reports (DR) are forwarded to ______ ____________

Back 93

Higher headquarters

Front 94

Within how many hours must category I deficiency reports (DR) be forwarded to the originating point?

Back 94

24

Hint 94

##

Front 95

When should new equipment account custodians receive training?

Back 95

Before signing for the account

Front 96

The first section of a technical order (TO) number identifies the...

Back 96

Category and the aircraft mission type in the TO

Front 97

Which technical order (TO) describes the Air Force TO systems?

Back 97

00-5-1

Hint 97

##-#-#

Front 98

Which type of technical manual is divided into tasks that cover a particular maintenance action?

Back 98

Job Guide

Hint 98

Step by step instructions

Front 99

Which type of manual is used by maintenance personnel as a means of isolating and rectifying system or component malfunctions?

Back 99

Fault Isolation

Hint 99

Read carefully!!!

Front 100

What section of the Illustrated Parts Breakdown (IPB) contains definitions of the codes used in the IPB?

Back 100

Introduction

Front 101

Which Air Force technical order (AFTO) information management tool (IMT) Form 22 recommendation would you submit that, if not corrected , could cause personnel injury or damage to equipment or property?

Back 101

Urgent

Front 102

In the reliability centered maintenance (RCM) approach, which preventive maintenance task is a scheduled inspection to detect a potential failure condition?

Back 102

On condition

Front 103

Which technicians provide maintenance activity data to the engine trending and diagnostics (ET&D) program?

Back 103

Propulsion and nondestructive inspection