Aviation Maintenance Ratings Ch. 3 Navedtra 14022

Front 1

What type of code is AK7

Back 1

supply project code

Front 2

Your squadron is categorized as a FAD II activity and you require a mission essential part. What is the highest priority that can be assigned to your request?

Back 2

2

Front 3

When a FAD III is assigned to your activity, what is the highest priority you should use to order routine replenishment stock?

Back 3

13

Front 4

Information from what source is used by supply department personnel as justification for stocking material?

Back 4

usage statistics

Front 5

What type of code identifies the agent or agency that has design control over an item?

Back 5

CAGE

Front 6

What is the purpose of an illustrated parts breakdown?

Back 6

To allow supply and maintenance personnel to identify and order replacement parts for aircraft or equipment

Front 7

What section in an IPB contains general information and instructions for using the publication?

Back 7

Introduction

Front 8

Besides the introduction, each IPB includes what information?

Back 8

Table of contents or alphabetic index, group assembly parts list, and numerical index

Front 9

What section of the IPB contains an explanation of the source or SM&R codes used in the IPB

Back 9

Introduction

Front 10

What listing in the IPB lists aircraft assemblies and identifies the pages or figure numbers where the assemblies are shown in the IPB?

Back 10

Alphabetical index

Front 11

What section of the IPB contains a description of a component listed in the IPB

Back 11

Group assembly parts list

Front 12

What section of the IPB lists supplementary handbooks to which you may refer?

Back 12

Introduction

Front 13

What is the purpose of an index number in an IPB

Back 13

to establish the relationship between parts in the illustration and the corresponding parts list

Front 14

T/F An SM&R code is a five or six position alphanumeric code.

Back 14

True

Front 15

What part of a part's SM&R code indicates how the part is to be acquired?

Back 15

Source code only

Front 16

What position of the SM&R code identifies the maintenance level assigned to completely repair an item?

Back 16

Fourth

Front 17

What information does the third position of an SM&R code provide?

Back 17

The lowest maintenance level authorized to remove, replace, and use item

Front 18

When removal of a component from an aircraft is not feasible or advisable until a replacement is on hand, supply personnel can exempt the turn-in of the component (retrograde) if its part number is listed in what document?

Back 18

CRIPL

Front 19

What ASO publication contains a complete list of Navy-managed material that is classified as MTR?

Back 19

MRIL

Front 20

What type of material is listed in the CRIPL?

Back 20

material exempt from the one-for-one turn-in rule

Front 21

The reference number on a master cross-reference list refers to what number or numbers?

Back 21

Either a manufacture's part number, a drawing number, or a design control number.

Front 22

The MCRL is used to provide a cross-reference between what items of information?

Back 22

Reference number and NSN

Front 23

What is the purpose of the ICRL-A?

Back 23

To provide a list of repairables and the local IMA's capability to repair them.

Front 24

An ICRL-A is revised at what specified interval?

Back 24

Quarterly

Front 25

What ICRL Capability code is used for check and test only?

Back 25

A1

Front 26

Within the iCRL listing, what code is equivalent to Beyond Capability of Maintenance (BCM)-3

Back 26

X3

Front 27

To what reference should you refer to obtain an NSN or reference number for an item when you only know the description?

Back 27

ASG

Front 28

What is the 13-digit number called that identifies an item of material in the supply system?

Back 28

NSN

Front 29

What is the title of the overall program that provides the data required for effective management of support equipment at all levels of maintenance?

Back 29

AMMRL

Front 30

What command exercises overall program management for the AMMRL program?

Back 30

NAVAIRSYSCOM

Front 31

What information is provided by the first two digits in the FSC code number

Back 31

The major or broad category of the stock

Front 32

The NSN is comprised of what total number of digits?

Back 32

13

Front 33

What acronym identifies equipment that is required on the ground to make a system, subsystem, or end item of equipment operational?

Back 33

SE

Front 34

Within an activity, personnel in what rating normally maintain the IMRL?

Back 34

AK

Front 35

The IMRL contains how many major section?

Back 35

5

Front 36

At the organizational maintenance level, the point of contact for all material requirements generated y a squadron is located in what organization?

Back 36

Material control center

Front 37

What Material Condition Code tells you that an iem of supply is fast moving and in high demand?

Back 37

F

Front 38

To determine whether an intermediate maintenance activity has capability to test/check or repair an item, what I-level supply area screens all components turned into ASD/SSC?

Back 38

AMSU

Front 39

The ASD/SSC is composed of what section or sections?

Back 39

SRS and CCS

Front 40

The SRS limits the quantity of any item in the pre-expended bin to a 30 day supply.

Back 40

True

Front 41

Within an activity, what officer must approve the item of PEB stockage when it costs more then $150?

Back 41

The commanding officer

Front 42

Supply will remove an item from the PEB if there has been no demand for the item within what total period of time?

Back 42

1 year

Front 43

What is the purpose of the component control section within the supply department?

Back 43

To manage the LRCA at the ASD/SSC

Front 44

A LRCA is assigned a workload priority. The priority assigned is one of what total number of priorities that can be assigned to the LRCA

Back 44

4

Front 45

An aircraft is NMCS/PCS status. What priority is assigned to LRCA in support of this aircraft?

Back 45

Priority 1

Front 46

AK0

Back 46

Assigned only when requisitioning material to restore an aircraft to mission capable status.

Front 47

AK7

Back 47

Assigned when requisitioning material to return mission essential subsystems to an operational condition when an aircraft is in a partial mission capable status.

Front 48

ZA9

Back 48

forced high-time removal items required for immediate end use on primary mission weapons systems.