Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
73 Cards in this Set
- Front
- Back
- 3rd side (hint)
|
Increase of elbow psi |
Clogged annuals ring |
Creates a vortex |
|
|
Max capacity of the gravity tank |
1144 |
|
|
|
What meters and prevents over heating of hydra fluid on ngl |
Metering screw 8.5 gallons |
|
|
|
What is the dia of the orifice for the steam steam pressure cutoff |
3/16 of an inch .187 |
|
|
|
Steam pressure cutoff switch open and close at what set pressurs |
Opens at 10+-2 closes at 20+-1 |
|
|
|
What is nominal cylinder expansion for c13 catapult. |
7.0 inches |
|
|
|
What component acts as a seal for the lower part of the retract vlv |
V- ring packing |
|
|
|
How many slippers are there on the a/g cross head assembly |
16 phenolic slippers |
|
|
|
The fluid cooler has a total of how many u shaped tubes ? |
107 |
|
|
|
Maximum operating temp for the a/g |
170 deg |
|
|
|
Service stroke of the Sable anchor damper assembly |
15ft. 8 inches |
|
|
|
What is the max desired zinc temperature |
950 to 1000 |
|
|
|
Zinc must be discarded at what temperature |
1075 |
|
|
|
In the a/g socket pouring process your Flux solution must be heated to |
160 - 210 |
|
|
|
Desired temp of the terminal |
550-600 |
|
|
|
Barricade hydra systems holds how many gallons max |
125 gallons |
|
|
|
Power pack fluid reservoir holds how many gallons? |
100 gallons |
|
|
|
Proper fluid lvl for power pack is what? |
Mark +/-2 inches |
|
|
|
What is the accumulator for power package hydrostatically tested too? |
2250 psi |
|
|
|
Operating press for accumulator for power package is what? |
1500 psi |
|
|
|
Proper accumulator lvl for power package is? |
Mark +/-1 inch |
|
|
|
What press does your motor turn on for the power pack? |
1250 psi |
|
|
|
What prevents overcharging of the accumulator for the power package? |
Spring loaded relief vlv |
|
|
|
The spring loaded relief vlv for the power package will partially open at and fully open too? |
Partial 1600 fully open at 1750 psi |
|
|
|
What is the size of your counter ballance springs for your barricade stanchions? |
7/8 |
|
|
|
Recession on entire zinc surface for pouring sockets is what? |
.060 anything higher reject terminal |
|
|
|
Retractable sheave height? |
4 7/8 inch |
|
|
|
Replacing cross head slippers at what total clearance reached. |
Horizontally .060 vertically .030 or more |
|
|
|
What is the form used die alre maf? |
4790.160 |
|
|
|
What is the standard supply requisition form? |
1348 |
|
|
|
Who signs all pms boards? |
Weekly- divo quarterly-department head cycle-deparment hd |
|
|
|
What type of fluid dies the arresting gear engine use? |
Ethylene glycol |
|
|
|
Weight selector unit fur cro vlv uses what electric source? |
440vlt 60 hers 3 phase |
|
|
|
Correct tow test for hot or cold catapult? |
Hot-1500 cold 2500 |
|
|
|
Decrease of elbow pressure |
Clogged basket strainer |
|
|
|
Maximum outside diameter of choke ring? |
15.900 |
|
|
|
What prevents excessive slack in the purchase cable between the cross head and fixed sheave? |
Cable anchor damper |
|
|
|
What is the dia of the pressure breaking orifice elbow |
.750/-3/4 of inch |
|
|
|
What component transfers motion by me as of drum assembly to the drive system |
Hyra motor |
|
|
|
Where is the launch vlv located ? |
Steam accumulator & thrust exh unit |
|
|
|
What is used to position the spindle in the csv? |
Motor unit |
|
|
|
How many panels does the mark 7 mod 0/2/3 jbds have? |
6 |
|
|
|
What is the source of the jbds? |
115v, 60 hz |
|
|
|
What is the correct tension. For the spring assembly for the retract vlv? |
50pds |
|
|
|
Upper portion of the retract vlv is connected to what? |
Accumulator |
|
|
|
Lower portion of the retract vlv is connected to what? |
Mec & anchor damper |
|
|
|
What is the initial stroke that is provided by the retract vlv plunger |
11/16 |
|
|
|
What component keeps the cables taut during arrestment? |
Anchor damper |
|
|
|
What is ideal cam index |
0 degrees |
|
|
|
What is the position of the cross head when in battery? |
Fully extended |
|
|
|
What is the dia of the ram? |
20.000 |
|
|
|
What is used to prevent fluid leaks of the fluid cooler? |
Copper annealed gasket |
|
|
|
What is the min and max lowering times for emergency lowering? |
Min 35/ 120 max |
|
|
|
What type of valve is the emergency cutoff valve? |
2 position 4 way vlv |
|
|
|
The jbds stack valve is what type of valve? |
3 position 4 way valve stack valve |
|
|
|
Mod 4 sheave damper accumulator fluid lvl? |
8-11 inches |
|
|
|
Mod 4 sheave damper initial charge? |
400 |
|
|
|
Mod 4 cross head sheave size? |
33 inch |
|
|
|
Mod 4\ what helps lubricate the sheaves? |
2 o-rings and a gasket |
|
|
|
Mod 4\ charge accumulator for sheave damper to what? |
400psi |
|
|
|
Mod3\ charge accumulator for sheave damper? |
750psi |
|
|
|
Cross head to cross head stop for clearance for mod 3 |
Mod 3/max-6"min -1"/ max recently reeve engine 7" |
|
|
|
What is the size of the packing in the ram? |
Min of 0 to .0010 to prevent leaking due to vibration |
|
|
|
How many sheaves are in the cross head assembly? |
18 sheaves 2 banks of nine sheaves each. |
|
|
|
Max allowable depth for sheave grove wear is? |
1 7/16 |
|
|
|
The pressure regulator for the autp lube system reduces ships service air to? |
75-86 |
|
|
|
Accumulator ruptures at what psi? |
1500 psi |
|
|
|
What type of packing is in your accumulator? |
2 sets of chevron packing |
|
|
|
The air expansion flask is initially charged to what and goes to what during arrestment? |
400/650 |
|
|
|
What is ideal temp for for arresting gear? |
130 ideal 170 max |
|
|
|
What kind of packing is on the lower side of the retract valve |
1 set of chevron packing |
|
|
|
What provides a seal between the bod and the vlv seat to prevent accum psi from leaking? |
Oring |
|
|
|
What are the only sheaves with oring? |
Thru-deck sheaves |
|
