Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
108 Cards in this Set
- Front
- Back
|
Mod 3 sheave damper operating pressure. |
750 psi |
|
|
Mod 4 sheave damper operating pressure. |
400 psi |
|
|
Service stroke of the sheave damper. |
8-10 ft |
|
|
S/D Flapper valve flow. - On arrestment - On retraction |
- unrestricted on arrestment - restricted on retraction |
|
|
S/D accumulator fluid level. |
1- 3 inches |
|
|
S/D Accumulator pressure increases to ( ) psi on arrestment |
1500 psi |
|
|
S/D dyno test. |
No more than 2700 lbs |
|
|
Sheave inspected |
- Semi annual or ever 2500 traps - throat wear: 1.469" - lip wear: 1/8" no less - max phenolic wear: 4.028" - spacer thickness: .266" or less replace. |
|
|
Purchase cable & CDP diameter |
1 7/16 " |
|
|
CDP length |
110 ft |
|
|
CDP breaking strength |
205,000 |
|
|
Purchase cable breaking strength |
215,000 |
|
|
Purchase cable inspection |
Every 300 traps / monthly. Up to 900 then every 100 traps |
|
|
CDP height |
2 - 5 1/2" |
|
|
Number of clamps for stretch tests |
14 |
|
|
Stretch test psi |
200 psi increments up to 1000 psi and hold open for 5 mins. |
|
|
After 2nd barricade arrestment what is sent to lakehurst? |
50 ft of cable from port and stbd sides |
|
|
Barricade CDP length? |
88 ft |
|
|
Barricade extension pendant length? |
10 ft |
|
|
Wire support cam index wear. |
.015" |
|
|
Wire support forward stop gap minimum? |
1/8 " |
|
|
Engine fluid cooler operating temp? |
80 - 130 °f |
|
|
Engine Fluid cooler max temp? |
170 °f |
|
|
Replace zinc anodes when? |
1/2 gone |
|
|
Number of zinc anodes in engine fluid cooler? |
6 |
|
|
Engine fluid capacity without cooler? |
380 gal |
|
|
Engine fluid capacity with cooler? |
580 gals |
|
|
Engine accumulator pressure increases to ( ) psi on arrestment |
650 psi |
|
|
What type of water and how much can be added to the AG engine? |
Distilled water (50Gal) (30Gal for barricade engine) |
|
|
Replenishment tank capacity |
6 Gal |
|
|
Engine revved ratio? |
18:1 |
|
|
Anchor Damper service stroke ? |
15 ft 8 in |
|
|
Engine accumulator max bore |
20.250 |
|
|
Engine normal run out |
183" |
|
|
Power pack capacity |
125 Gal |
|
|
Power pack pressures - operating pressure - kicks on at - cracks open - fully opens |
- 1500 - 1250 - 1600 - 1750 |
|
|
Number of deck ramps |
12 |
|
|
Mod 4 deck ramps |
10 |
|
|
Number of impact pads in picture frame |
13 |
|
|
Popping barricade height off deck |
6 - 12" |
|
|
E2C2 midspan height |
21 ft |
|
|
E2C2 center clearance |
40 ft |
|
|
Ready jet midspan height |
20 ft |
|
|
ARC weight setting X = |
10,000 lbs |
|
|
Psi difference between gauge and GUI |
No more than 150 psi |
|
|
(Primary/alt bus) ARC engines match weight setting within |
+- 200 lbs |
|
|
(Manual mode) ARC engines match weight setting within |
+- 500 lbs |
|
|
Auto Lube pressure |
80+-5 psi |
|
|
Auto lube shots (normal) |
6 shots / 30 seconds |
|
|
Auto lube shots (newly reeved first 50 traps) |
24 shots / 30 seconds (old as fk) |
|
|
Aux air pressure |
2500 - 3000 psi |
|
|
HPU fluid capacity |
5 Gal |
|
|
Primary and failsafe accumulator pressure |
2525 - 2950 psi |
|
|
HPU hose service life. |
6 years |
|
|
RCV spring |
103 lbs ( I have 50 lbs) |
|
|
RCV motor |
90 hp |
|
|
Two types of transducers |
5k & 15k |
|
|
UPS power time |
2 hours / 30 traps |
|
|
UPS batteries |
Twenty - 12v batteries |
|
|
Max allowable float |
0 - 1/32" |
|
|
No wire within ( ) of terminal wall |
3/8" |
|
|
Max recessions - new - R5 |
- .060 - .125 |
|
|
Socket pouring drill |
450 - 700 rpm |
|
|
Replace bent tube after |
11 wires |
|
|
Degreaser ratio/time/temp |
4:1 Water:degreaser 45 - 60 min 90 - 100°f, 110°f max |
|
|
Flux temp |
160 - 210°f |
|
|
Socket pouring water temp |
160 - 200°f |
|
|
Flux expires |
20 years from manufacturing date |
|
|
White temp stick |
550 °f |
|
|
Red temp stick |
600 °f |
|
|
Zinc temperature |
925 - 975°f Discard after 1075°f |
|
|
Pull test new sockets at |
120,000 lbs for 2 mins |
|
|
Wire recessions |
Max of six No deeper that 1/32" |
|
|
Mod 4 retractable sheaves |
Height 7 inches 160+/-5 psi |
|
|
Barricade stantion height |
24 ft |
|
|
Counter balance springs adjusted in the |
Raised position |
|
|
Engine vertical slippers prevent |
Fish tailing of X-head |
|
|
What secures the MEC to the 5in sleeve? |
4 segmented clamps |
|
|
Number of slippers on ram slipper cage |
12 |
|
|
What secures the Ram to the X-head? |
Split retainer |
|
|
Ram packing float set to ( ) to prevent leaking due to vibration |
0 - .010 |
|
|
Sheaves in a nest |
18 |
|
|
Sheaves in a bank |
9 |
|
|
Number of slippers on X-head |
16 |
|
|
Number of spacers per bank |
10 8 bonded 2 loose |
|
|
Max high speed spacer wear |
.050" |
|
|
Sheave throat depth |
Max: 3/16" New: 1 1/4 |
|
|
Flex hose reel tension |
9 +/- 1/2 ft lbs |
|
|
Master distribution block relives at |
2200 |
|
|
Primary distribution block relives at |
1800 |
|
|
Accumulator safety disk ruptures at |
1500 psi |
|
|
Accumulator hydrostatic test to |
2000 psi for 30 mins |
|
|
Accumulator floating piston slipper cage has ( ) slippers |
24 12 on both sides |
|
|
Accumulator air tightness test |
Charge to 1000 psi Let sit for 24 hrs Max 20 psi drop for temp changes |
|
|
Aux air flask hydrostatic test |
5000 psi |
|
|
Number of copper tubes in cooler |
107 Max of 20 pluged |
|
|
Scavenger tank capacity |
90 Gal |
|
|
Stowage tank capacity |
700 |
|
|
Max high speed spacer wear. |
.050 |
|
|
What holds the retract valve closed |
Spring tension and accumulator pressure |
|
|
S/ D flow control valve orfice |
1/2 |
|
|
Counter balance cable diameter |
7/8 |
|
|
Tensioning pendant cable diameter |
5/8 |
|
|
wet webbing |
10 - 15 % reduced strength 40 - 45 % increase weight |
|
|
Dragging a barricade webbing. |
Reduces strength by 30 - 35% |
|
|
Barricade webbing shelf life |
1- 8 = 7 out of box 9 = 6 10 = 5 11 = 4 12 - 15 = 3 |
|
|
O ring shelf life |
5 year / 20 qtrs |
|
|
V ring shelf life |
3 years / 12 qtrs |
