Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
53 Cards in this Set
- Front
- Back
Primary purpose of an LCAC
|
high speed ship to shore, transports passengers/ equipment "over the horizon"
|
|
Purpose of LCAC (Con't)
|
Provides civil/ humanitarian relief- can deliver life saving supplies and equipment to otherwise inaccessible sites/ provides medvac
|
|
Two operating conditions of an LCAC
|
On cushion- Rides cushion of air with small gap between tips of fingers and water
Off cushion- (boating mode) A floating barge |
|
The LCAC is propelled by:
|
2 ducted propellers mounted aft
2 bow thrusters 4 (ET40B) engines 4 Double entry centrifugal fans |
|
Lift fan flow percentage to bow thruster and cushion
|
60% cushion
40% Bow thruster |
|
Percentage of THRUST from bow thruster and propellers
|
Propellers- 80%
Bow thrusters- 20% |
|
LCAC increase shoreline landing sites from 17% to:
|
70%
|
|
LCACs are compatible with how many ship classes?
|
6
|
|
What support ship classes support LCAC operations/ how many LCAC can be transported on each?
|
LHD-1 (3)
LHA-1 (1) LPD-4 (1) LPD-17 (2) LSD-41 (5) LSD-49 (2) |
|
HULL length
(less cushion) |
81' 10"
|
|
LCAC length on cushion with deep skirt
|
91' 9.5"
|
|
HULL beam width
(less cushion) |
46' 10"
|
|
Beam width on cushion with deep skirt
|
47' 10" @ design N2
49' 2" @ reduced N2 |
|
Hull borne height
(light payload) |
17' 2.5"
|
|
Hull borne height
(heavy payload) |
16' 6"
|
|
Height
(Off cushion) |
19' 2"
|
|
Height on cushion with deep skirt
|
25' 10" @ design N2
24' 4" @ reduced N2 |
|
Height on cushion, mast extended, with deep skirt
|
34' 5.5"
|
|
Craft design weight (SLEP LCAC)
|
344,658 lbs
|
|
Hover height
|
7'
|
|
TACW
(total allowable craft weight) |
mission dependent
|
|
MACW
(maximum allowable craft weight) |
389,984 lbs
|
|
Baseline light craft weight with no fuel
|
211,533 lbs
|
|
Buoyancy box- comprised of what decks
|
cargo deck
second deck ( lower skin of craft) |
|
Buoyancy box-
How many water-tight compartments? |
45
|
|
Buoyancy box-
How deep is the buoyancy box |
3.5'
|
|
What material are LCACs primarily composed of
|
5456 marine aluminum alloy
|
|
Cargo deck-
How many longitudinal tie down rails are there? |
4
|
|
Cargo deck-
Constructed of what thickness aluminum? |
3/8"
|
|
Ramps-
constructed from what? |
welded aluminum plate
|
|
Length of Bow ramp
|
28' 4"
|
|
Length of Stern ramp
|
14' 10"
|
|
Ramps can be raised manually using a:
|
Hydraulic hand pump
|
|
The superstructure includes:
|
(CCM) Command and control module
(PEM) Personnel and Equipment module APU modules Lift fan modules Prop shrouds |
|
How many persons can be transported in the CCM?
|
7 seats in lower deck
5 seats in upper deck |
|
How many Passengers can be transported in the (PEM)
|
17 total
16 pax/ 1 load master |
|
how many non-combatant Passengers can fit, not including crew
|
23
(7 ccm, 16pem) |
|
Combat loaded troops decrease capacity by what percent?
|
20%
|
|
Purpose of Prop shroud
|
Directs air for thrust
|
|
Length of prop shroud
|
14'
|
|
Purpose of the deep skirt
|
Skirt keeps air contained under craft, the flexibility of the skirt enables the craft to remain on cushion in rough sea and over land
|
|
Weight of skirt
|
16,000 lbs
|
|
Skirt is made out of what material:
|
nylon impregnated neoprene
|
|
Skirt fingers are made out of what material
|
Nylon impregnated rubber
|
|
Skirt system is constructed of how many segments?
|
12
(1 FWD) (1AFT) (5 PORT) (5 STBD) |
|
Skirt segments consist of :
|
Outer and inner bag assemblies
|
|
Purpose of lateral stability seal
|
lateral stability seal divides the air cushion into two chambers,restricting movement of cushion air
|
|
What type of skirt fingers are on the aft segment
|
Reinforced planning cone fingers
|
|
Cushion interior length
|
79'
|
|
Cushion interior beam
|
40' 6"
|
|
Cushion area
|
3,136 SqFt
|
|
Cushion pressure (design weight)
|
104 ft lbs
|
|
Cushion splice hardware
|
magna grip lock bolt
|