Observation & Calculations for Nanorefrigerant Graph of C.O.P. vs. Nanoparticle Concentration for Nanorefrigerant. C.O.P RESULTS WHEN NANOPARTICLE MIXED IN R134A & POE OIL Figure 5.1. Graph of nanorefrigerant C.O.P vs. nanolubricant C.O.P. 5.2. GRAPH OF PERCENTAGE CHANGE IN THE COP OF THE SYSTEM Figure5.2. Graph of percentage C.O.P of nanorefrigerantvs. nanolubricant. Here the result shows the percentage change in the C.O.P when the air conditioning test rig run on the nanorefrigerant and…
3.3.3 Selection of Die Angles The split die was designed for the ease of assembly for fabrication. AISI 52100 steel was selected as the material for the die fabrication. The entry part of the die is 12 mm and has 120 mm length. The profile of the die is also shown in the solid works software. The angle of the die is 90 is maintained, the slope radius is 20 mm. the Figure.3.1 & Figure. 3.2. illustrate the split die design and solid works model of the split die. Figure. 3.1 : Split die…
3. MIX DESIGN 3.1 Design of Geopolymer Concrete Mixtures: In the mix design of geopolymer concrete the role and the influence of aggregates are considered to be the same as in the case of Portland cement concrete. The mass of combined aggregates may be taken to be between 75% and 80% of the mass of geopolymer concrete. Coarse and fine aggregate together were taken as 77% of entire mixture by mass. Fine aggregate was taken 30% of total aggregate. Fly ash and alkaline liquids was taken 23% of…
In the paper, FePO4 was studied in through neutron powder diffraction across a wide range of temperatures, and was found to have 2 states in general, the α (alpha) phase and β ( beta ) phase. The alpha phase exhibits a tetrahedral structure, which is similar to alpha quartz, and this occurs during generally low temperatures. In the case of this paper, the temperatures experimented on were between 294K and 1073K. The beta phase, however, is denser and exhibits a octahedral structure. The…
(3) The boundary layer mass transfer equation in batch system is as: dq/dt=(3k_f R(C-C_s ))/(D_s ρ(1-ε)) (4) The equation of material balance for slurry adsorption system is studied using…
Though sloping roofs are commonly used all over America, flat roofs are steadily gaining a lot of popularity. This is mainly because they have a host of benefits to offer as far as homeowners are concerned. Now, there might be some of you who do not have a clear idea as to what flat roofing actually is. Well, they are not entirely flat but have a slight amount of slope that is usually of about 10 degrees to facilitate draining of water and snow. The concept of flat roofs was introduced centuries…
A Ban on Water Bottles In the article ‘’ A Ban on Water Bottles: A way to bolster the University’s image’’ Amanda Jacobowitz discusses the ban of water bottle sales in her campus. The University of Washington has arranged an accession to ban water bottles over the usage of plastic. Water should be a product available at any campus for dehydration. Having an ecofriendly environment can change people’s perspective on how much plastic is being withered. The amount of water usage it takes to make…
choice for pavers, bluestone tends to be extremely versatile. Not only for pavers, but bluestones is also used for garden paths, poolside, patios, driveways, and more. Most homeowners consider not only the price but also the safety aspects of the material before making a choice of a stone. Though this stone can be used indoors as well as outdoors, this tends to be more beneficial when used in the outdoors. This stone being porous can hold and bear water for a long span of time. If you are…
with a dental material that will be biocompatible with the tooth and resist the hostile oral environment. Dental materials are incorporated into the teeth structure by retention. This retention can accomplished through mechanical, chemical adhesion or bonding mechanisms between materials and the dental structure. Mechanical retention is used when amalgam is placed, by securing it through undercuts, so that the floor is wider than the opening of the preparation. Composite materials or dental…
The past chapter proposed the continuous floating constraint and buckling column concept. In this chapter, a test setup is proposed to investigate its loading nature and validate the concept. A series of tests are performed, and the results are presented and discussed. The results of the tests conducted in this chapter will serve as measures in assessing the strengths and flaws of the initial concept, and point towards potential solutions. This group of tests varied two geometric parameters:…