Transcranial direct current stimulation

Decent Essays
Improved Essays
Superior Essays
Great Essays
Brilliant Essays
    Page 3 of 4 - About 40 Essays
  • Decent Essays

    1762-IF4 is an Allen Bradley MicroLogix 1200 System with 4 Channel Current/Voltage Analog Input Module. It has a dimension of 90 x 87 x 40.4 mm. It has Delta-Sigma converter and 4 differential (bipolar) inputs. It’s analog operating voltage range is -10 – 10 V DC normal and -10.5 – 10.5 V DC full scale. It’s analog operating current range is 4 – 20 mA normal and -21 – 21 mA full scale. It converts the analog input up to the full-scale range. It enhances the functionality of MicroLogix 1200…

    • 264 Words
    • 2 Pages
    Decent Essays
  • Improved Essays

    To do Cable calculation it has to meet the requirements from BS 7671. Design Current First thing to do is calculate the design current. (Ib) I=Watts/Volts. You do this so you can find out the total current. Apply Diversity Factors (where applicable) Diversity is described in the onsite guide Appendix A as a way to determine the maximum demand for an installation and includes the current demand for commonly used equipment. For example if in a domestic household there were 8 lights on a…

    • 827 Words
    • 4 Pages
    Improved Essays
  • Improved Essays

    Resistivity In Wire

    • 1530 Words
    • 7 Pages

    This is resistance, which is measured in units called ohms. Resistance is a term that describes the forces that oppose the flow of electron current in a conductor. All materials naturally contain some resistance to the flow of electron current. We have not found a way to make conductors that do not have some resistance. If we use our water analogy to help picture resistance, think of a hose that is partially plugged with sand. The sand will…

    • 1530 Words
    • 7 Pages
    Improved Essays
  • Improved Essays

    site are caused by overhead or underground electrical lines." In an article by Darlene Bremer, she states "electrocutions kill an average of 143 construction workers each year. More than half of the electrocutions of electrical workers were caused by direct or indirect contact with live electrical equipment and wiring, control panels, junction boxes and transformers." According to OSHA, they estimate that there are approximately 350 electrical related deaths per year, which almost averages one…

    • 796 Words
    • 4 Pages
    Improved Essays
  • Great Essays

     Novel 3-Phase Single stage boost inverter: Analysis, Design and Experimentation M K Pathak, Member, Dogga Raveendhra and Aravind Panda Abstract— this paper introduces a novel type of 3-phase single stage dc-ac converter, which is controlled by sliding mode control, offers intrinsic step up abilities. Proposed inverter is designed with lesser number of solid state semiconductor switches and small passive elements. Sliding mode controller (robust controller) is designed to control this power…

    • 1551 Words
    • 7 Pages
    Great Essays
  • Improved Essays

    Winders, Jr In a Y-Y transformer the zero-sequence magnetizing currents produced by the odd harmonics all meet neutral point producing the current that goes through the neutral going back to the voltage supply. It also stops any distortion in the secondary phase voltages as the magnetic flux in the core of the transformer has a sinusoidal waveform and since…

    • 1239 Words
    • 5 Pages
    Improved Essays
  • Improved Essays

    Arduina Case Study

    • 1359 Words
    • 6 Pages

    1.1. BLOCK DIAGRAM CHAPTER 2 2.1. COMPONENTS • Arduino – Purpose of processing • Voice Recognition Module – Voice command identification • Motor controlling Circuit – Motor Control • Gear Motors – Direction variation & constant speed running 2.1.1. ARDUINO Arduino Mega contains everything needed to support the function of the micro controller. It includes digital output/input pins & analog input pins. It connects to a computer through USB cables or power it by a use of AC…

    • 1359 Words
    • 6 Pages
    Improved Essays
  • Improved Essays

    Poolco Case Study

    • 1677 Words
    • 7 Pages

    In test system-II, primarily a two area multi source power system is considered with three GENCOs and two DISCOs in each area is shown in Fig. 8. The control area 1 and control area 2 comprises of reheat thermal, hydro and gas power system with the inclusion of non-linearities such as boiler dynamics, time delay (TD), governor dead band (GDB) and generation rate constraint (GRC). Boiler dynamics configuration is incorporated in thermal plants to generate steam under pressure. Changes in the…

    • 1677 Words
    • 7 Pages
    Improved Essays
  • Improved Essays

    Case Study Of Split Die

    • 1086 Words
    • 5 Pages

    3.3.3 Selection of Die Angles The split die was designed for the ease of assembly for fabrication. AISI 52100 steel was selected as the material for the die fabrication. The entry part of the die is 12 mm and has 120 mm length. The profile of the die is also shown in the solid works software. The angle of the die is 90 is maintained, the slope radius is 20 mm. the Figure.3.1 & Figure. 3.2. illustrate the split die design and solid works model of the split die. Figure. 3.1 : Split die…

    • 1086 Words
    • 5 Pages
    Improved Essays
  • Improved Essays

    • Diverse types of mental stimulation make people who suffer Alzheimer’s to feel more engages with life since these stimulations foster their thinking capacities and mitigate any chances of memory lapses (Gonsalvez et al., 2016). When incorporated in the fMRI scans processes, mental stimulation, which involves processes that are desired to bring pleasure to those people who are prone to the disease, effectively…

    • 1398 Words
    • 6 Pages
    Improved Essays
  • Page 1 2 3 4