Titration

Conclusion: I predicted that liquid A was glycerine due to a calculated density of 1.38 g/mL. However I was wrong the actual density of liquid A was 1.38 g/mL and the substance was actually corn syrup. Therefore the percent of error for the density of liquid is 1%. For liquid B I had predicted that its substance would be Glycerine due to the calculated density of 1.19 g/mL. I was incorrect for the density of liquid B which was actually 1.26 g/mL, but because the calculated and actual densities…

Conclusion The empirical formula of the copper chloride hydrate compound is CuCl2 · 2H2O. Discussion of Theory The technique of gravimetric analysis can be used to find the empirical formula of a compound when the amount of it is known. By dehydrating the copper chloride hydrate sample and using it for an elemental copper-producing chemical reaction, one can isolate the masses of the water, copper, and chloride and determine their mole ratios. Since the Law of Definite Proportions states that a…

Ethyl vinyl ether was used to protect –OH on glycidol based on a literature reported protocal.59 In a typical procedure, 0.675 mol glycidol and 200 mL ethyl vinyl ether were loaded in a round-bottom flask, to which 1.25 g TsOH was then added. The reaction was allowed to proceed at room temperature (RT) for 3h. The resulting mixture was then purified by washing with 100 ml saturated aqueous solution of NaHCO3 for 3 times. The organic layer obtained was dried by MgSO4. After filtration of MgSO4,…

The objective of the lab was to determine the densities of known and unknown metal solids and liquids. For the liquids, initially, an Electronic Scale was placed onto Work Bench, and it was zeroed. An empty 50 mL Graduated Cylinder was placed onto the scale, weighing 54.00 grams. In increments of 10 mL. Until the volume was 30.00 Ml, 10.00 mL of water was poured into the Graduated Cylinder. In between each increase of 10.00 mL, the total volume and mass were recorded. For the known metals, the…

The reaction of soda ash (Na2CO3) with calcium sulfate in water is represented by the following chemical reaction: Na2CO3 + CaSO4 >>> CaCO3 + Na2SO4. Assuming that this reaction is complete and that there is 153 mg/l of CaSO4 initially present, what is the mass of soda ash that must be added to 1 liter of the water? How many grams of CaO are required to be the chemical equivalent of 246 g of Mg(HCO3)2? A complete reaction requires the number of CaSO4 to be equal to the number of moles…

NIMOTOP INJECTION Nimodipine 0.02% solution contains the following excipients: Ethanol 96%, Macrogol 400, sodium citrate, citric acid, Water for Injections Ph. Eur. These excipients consist of properties that aim towards the proper functionality of Nimotop. They consist of inherent stabilities that cause little or no effect in the stability of the drug and they do not have any acute or chronic toxicity. The excipients are also added into the Nimodipine 0.02% solution to enhance the biological…

DISCUSSION There are three chemical properties will be discussed which are combustion, reaction with bromine and reaction with potassium permanganate. Combustion was used to test the unsaturation of hydrocarbon. The degree of unsaturation refers to the number of the rings and / or multiple bonds present in the hydrocarbon molecule (McMurry, 2015). Hexane was a saturated hydrocarbon, it completely combusted and emitted carbon dioxide plus water. Cyclohexene was an unsaturated hydrocarbon, it…

Getting sprayed by a skunk is no fun at all. It is the worst smell and the odor sticks to everything, It's probably no surprise that the same chemical compound called thiols that's found in skunks' stinky spray is also present in rotting flesh and feces. It just plain out stinks! How to remove skunk smell? In a plastic bucket (not metal), mix the following ingredients thoroughly: 1 quart of 3% Hydrogen Peroxide 1/4 cup of baking soda 1 tablespoon of liquid dish washing soap (Ivory is…

The researchers compared both biologically produced manganese oxides and chemically produced manganese oxides for the oxidation of diclofenac. Because biologically produced manganese oxides are known to have high specific surface areas and high catalytic reactivity, this substance offers higher rates of oxidation for diclofenac when compared to chemically produced manganese oxides.² If biologically produced manganese oxides prove to completely eliminate diclofenac from the water supply, the…

Truc-Nhi Do Separation of a Mixture The purpose of this lab was to separate a mixture, calculate the percent composition by mass, and find percent error. I first started out by taking the mass of each component of the lab. I used the infiltration method to allow the salt and water solution, a blended mixture, to pass through the filtration paper and into the beaker. A trick to know if something is a solution is to see is it has the aqueous sign (aq) in the formula, like NaCl(aq). This step…