Tensile strength

Engineering strain is defined as the amount of material that deforms per unit length in a tensile test. Engineering strain is also known as nominal strain. 2) In the figure below, graphically show the toughness of three class materials: Ceramics, Metals, and Polymers (un-reinforced) 3) Where is the elastic recovery in the graph below? 4) What is the relation between the yield strength of a material and the size of the grain in polycrystalline metal?…

In architecture and civil engineering, sustainability plays a main role. All buildings and any construction could be potentially dangerous if they were built or designed in an inappropriate way. All structures and designs have to be safe and stable to prevent the fatal catastrophe of failing construction. The construction of any large objects, such as shopping centers, cathedrals, bridges, and other usually takes a lot of time. There are many forces that affect the designed construction and…

Study of Stress Corrosion Cracking (SCC) in Alloys Jiang Jingxing 1. Introduction of Stress Corrosion Cracking Stress Corrosion Cracking (SCC) is the growth of cracks with a under the combined effects of a static stress and a specific chemical environment. All SCC failures involve a macroscopic brittle performance, and the ductility of the material is reduced. It is universally acknowledged that there is no single mechanism for stress corrosion cracking (Ford, 1984). Stress…

CHAPTER- 5 ANALYSIS OF STEEL LEAF SPRING ________________________________________________________________ The aim of this analysis is to study the multi-leaf steel leaf spring under loading conditions and verify those results within the allowable limits. ANSYS software is used to analyze the stresses and strains by performing static analysis for the given leaf spring specifications and modal analysis is performed to determine the natural frequencies and mode shapes to asses the behavior of the…

Experiment 37: Friction Anne Smolinski as910513@ohio.edu Wednesday 11:50-1:40 TA: Sanjoy Sarkar November 11, 2017 Experiment 37: Technical Report ABSTRACT In experiment 37, the friction force is being explained and tested by using a block that is being pulled across a wooden base. Out of the four different types of friction, two will be tested during this experiment: (i) static and (ii) kinetic. Static friction can be defined as the force that resists motion of an object to a surface so…

In this study, the Jumbo hopper (JH) barge is selected as a striking vessel. Also, the finite element models of impacted piers in isolated and multiple-pier cases including three piers and two spans are developed in LS-DYNA25 according to available characteristics in Consolazio et al.3 Fig. 1 shows the bow and non-bow (stern) portions of JH barge developed in LS-DYNA according to properties as given in AASHTO provisions.2 The bow portion of the barge contains the impact zone with outer plates…

Hardness Testing Lab 1 Moriah Ausherman E882U679 Kunza Arifa ME-251-10959 Thursday 3:30 Experiment Date- 8/31/2017 Due Date- 9/7/2017 Introduction: The purpose of this lab is to ascertain the hardness of two different materials. One material is aluminum the other will be determined through testing. Hardness is defined as a material’s ability to resist plastic deformation by indentation. Harder objects are more likely to resist deformation. The results of a hardness test will be…

was clear from the data obtained by polarized light microscope (Figs. 4G and H) that the Haversian system is found as an individual canal system, the boundaries, which are marked by an occasional very faint line representing what has been called the cement line by Cook et al. [47]. Osteocytes, found in cavities (lacunae) within the matrix, were noticed. Dark precipitate in the form of a thick black line may indicate the presence of calcium phosphate in…

Bridge Design: Edmond Liu My popsicle bridge is based on a truss design, which is a bridge design held up by a connected structure composed of many smaller pieces. In particular, my bridge is a variation of the Queen Post Truss Bridge, which has two central supporting posts to allow for a greater span allowing for larger contact points. (http://pghbridges.com/basics.htm)…

Moreover, metallic bonds have a simple crystal lattice in solid state and are the weakest primary chemical bonds. Hence the reason to why pure metals are dissolved with other elements such as: carbon for mild steels. Metal alloys have increased strength and hardness. The structure of alloys reduces the space between each ion, so there is less space for delocalized electrons and it improves the chemical bond with each element within the…