Steel mill

The Singareni Collieries Company Limited (SCCL) is a Government coal mining organization mutually possessed by the Government of Telangana and Government of India on a 51:49 value basis. The reserves of Singareni coal stretch over 350 Km of the Pranahita – Godavari Valley of Telangana with a huge amount coming up to 8791 million tons. SCCL is as of now working on 16 opencast and 31 underground mines in 4 regions of Telangana with an employee base of around 58,837. Sustainable Management in SCCL…

Nucor’s Growing Presence Nucor is one of the largest steel manufacturer’s in the world. The corporations vision is to be a global leader in the steal manufacturing business (Gamble, Peteraf, & Thompson, Jr., 2015). The success of the company is attributed to several factors. Expanding product lines to offer customers a myriad of steel products. All while providing the highest quality steel products at a lower cost than competitors. They accomplish this by using state of the art technology…

is precursor to stress corrosion cracking. If some pits are formed in proper condition, growth of crack takes place and propagation happens. Chu et al. (2004) had demonstrated microcracks during initiation. In Chu’s experiment X-65 pipeline steel samples were exposed to synthetic soil environment for 61 days and 111 days, and the morphology of two samples are shown in Figure 3. It was concluded that majority of initiated microcracks were generated from pits at metallurgical…

5. CREATIVE PHASE Table IV Functional Development to Cost (An Incline) Function Creative Ideas & Development Estimated Cost (Rs) Provide Surface 1) Change the material to Mild Steel 40 2) Change the copper to brass 70 3) Combine function of bracket 85 (For sliding surfaces, copper facilitates lu-brication & high con-ductivity.) (A) The existing cost of the Incline + Bracket assembly = 112…

As can be seen, multicem concrete showed resistance below the limit for structural lightweight concrete, which can be classified so as insulating concretes or moderate resistance. However, according to Radonjanin, Malesev, Marinkovic and Al Malty (2013), concrete made from 100% recycled coarse aggregate can achieve high compressive strength since large amount of cement to be added, which is therefore not an economical proposition. Still according to the author, concrete made with 50% or 100% of…

observe the stress concentration factor/feature for a set of mild steel specimens with various irregularities in each sample. These irregularities or “stress-raisers” include any notches and holes which vary in size (radius) and placement on the specimen (edge notches or holes) that may have an effect on the flow of stress. With the use of a Hounsfield 50 kN electrically operated tensile testing machine and 12 1-mm thick mild steel test samples the experiment shows how any stress-raiser within…

Properties of cold formed steel In general, cold formed steel has many important properties which make it significant building material, the main two properties of cold formed steel are: the yield point and the tensile strength and how are they related to formability of steel, most members in building industry are on high tensile loads, cold formed steel has a Huge tensile strength, however the ratio between the tensile strength and the yield strength is 1.2-1.8 .in addition to other good…

designed and fabricated supporting legs for a center lathe using ferrocement and its properties were compared with cast iron legs. The fabricated legs contains, sand: cement: water = (2 : 1 : 0.45). The Ferrocement legs were made of wire mesh with steel reinforcement cage . The static test results revealed ferrocement head-end and tail-end had 0.040 mm/KN, 0.58 mm/KN deflection unlike the corresponding values for the cast iron were 0.20 mm/KN, 0.21 mm/KN respectively being almost double the…

most important developments was the revolutionizing of iron and steel. The steel industry emerged around western Pennsylvania and eastern Ohio due to the fact that coal, which is used to fuel the furnaces, and iron, which is made into steel using a variety of methods, were found in abundance in that area. Pittsburg, P.A. became one of the centers of the steel world. New Jersey ironmaster Abram S. Hewitt introduced a process of making steel supplanted…

is named Sprout City. It is based on the manufacturing of steel and it follows the multiple nuclei model. We have chosen to base our manufacturing on steel because currently it is the leading construction material for sustainability. This essential to a city because when a city manufactures something that is commonly used or demanded a lot it will have a higher economy. This benefits both the basic industry and everyone else because steel is used for the building of roads, railroads, and other…