Table 2. Recorded data of Physical and chemical properties of Wakefield Pond. Figure 3. Graph of temprature vs Depth in each lake. Figure 4. Graph of oxygen concentration vs Depth in each lake. Figure 5. Graph of light vs Depth in each lake. Figure 7. Sketches of plankton and relative aboundace from all two lakes Figure 8. Sketches of plamkton and relative aboundance from all two lakes. Figure 6. Fish in Wakefield Pond variety and numbers. Discussion Lake…
1.1 Overview: In a research lab, Mr. Z trying to formulate a colloidal dispersion system with sodium lauryl sulphate. What type of colloidal system is suitable for sodium laurly sulphate and also we have to discuss the different stability factors for sodium laurly sulphate dispersion. 1.2 Solution to the question: Introduction of colloids: Colloids are homogeneous non-crystalline substances. Here one substance is divide into more minute particles called colloidal particles and then it…
Procedure: Part A: Extraction stage 1. Place a 125 mL separatory funnel in a ring stand equipped with a small ring. 2. Heat the hot plate. 3. Heat the water (20 mL of hot water is needed) to a boil by placing it on top of the hot plate. 2. To the 125 mL Erlenmeyer flask, added two Tylenol (500 mg/ tablet) 3. Dissolved the solid by gently swirling the Erlenmeyer flask. 4. Let the solution cool for a few minutes (approximately till room temperature). 5. Add the mixture to the separatory funnel.…
Seltzer/effervescent, Alcalak, and Medi-first were indirectly titrated with sodium hydroxide (NaOH), which is a strong base. By using the back titration technique, the amount…
molarity of the unknown substance. I believe that it will take around three hundred drops of sodium hydroxide (NaOH) for it to be able to reach to its endpoint of the unknown substance. My reason behind my hypothesis is… Methods In this lab experiment we use a buret to measure the amount of pure water we decide that we need. A weight boat to be able to measure the sodium hydroxide(NaOH) on the triple beam balance. We also used a beaker to put our…
1. Fill a mason jar half-full with tepid water. Put it on the hotplate and raise the temperature to 98 degrees. Make sure you can keep it at this temperature for several hours. 2. Wash your hands. Cover the surfaces adjacent to your kitchen stove with paper towels. Place the test tube racks close to the stove on the paper towels. 3. Fill the pot with water and bring to a boil. Uncap your test tubes. Using your kitchen tongs, carefully drop your graduated cylinder, test tubes and their caps in…
Out of many early photographic processes, I select the Anna Atkins Photographs of British Algae: Cyanotype Impressions, 1843 Cyanotype. I select this process because the color of this picture is very different to the others in the lecture making this photography stand out and get my attention. While I was doing my researches, I found out that the process to make this picture is not complicated, does not require a lot of materials, and needs a negative image which reminds me of the class activity…
predicted that sample number 2 is the oven cleaner that contains Sodium Hydroxide. Sodium Hydroxide (NaOH) is highly corrosive due to its elements; the presence of oxygen and an electrolyte (Sodium – Na) cause corrosion, the breakdown of a metal resulting from reactions with chemicals in its environment. The oxygen oxidizes with the metal, and the sodium help speed up the corrosion process. The presence of oxygen and electrolytes (Sodium – Na) in sample number 2 make it more…
Part one Make a 3 list of chemical safety hazards? The three chemical safety hazards are: Poison Toxic Corrosive Reactive Environmental hazards 2. What is Amalgam? Amalgam is mixture of metals of mercury with another metal and other metal. Almost all metal can be an amalgam with a form of mercury. 3. If you had to train someone on how to separate the mercury from the amalgam, what training would they need? WHY? If I had to train someone on how to separate the mercury…
Sodium alginate (SA) is a natural anionic polysaccharide obtained from sea weeds. It contains β-D-mannuronate (M) and α-L-glucuronate (G) residues linked by (1-4)- glycosidic linkages (Fig. 7.1) and arranged in homopolymeric blocks of each type and in heteropolymeric blocks [1]. It is a water soluble polysaccharide and has pKa values of 3.38 for the ‘M’ and 3.65 for ‘G’ units [2]. It can form complexes with positively charged polymers due to its anionic character. It is utilized as emulsifier,…