Silver chloride

the charges of the solvent. For instance, sodium chloride dissolves in water because the sodium cation has a positive charge and the chlorine anion has a negative charge. The water molecules also have partial charges because the oxygen is more electronegative than the hydrogen atoms, pulling electrons toward itself, producing a partial negative charge with a resultant partial positive charge on the hydrogen atoms. The charges between the sodium chloride and the water interact leading to a…

more efficient. It is then extracted using dichloromethane (DCM) and maceration. The chlorophyll and β-carotene pigments are dissolved into the organic DCM layer which is polar and does not mix with water. The solution is then washed with sodium chloride (NaCl) to draw out any remaining water left in the solution that was not dried out by the ethanol. [1] Water will move toward the more hypertonic solution and separate from the DCM extract. After successful separation of the pigments from the…

DISCUSSION 6.1 FTIR SPECTROSCOPY It was observed from the FTIR graph that there was no shifting of peaks of metronidazole i,e., characteristic peak of the amine group (N-H streching) present in imidazole nucleus at 1030 cm-1 and presence of NH2 group at 3298 cm-1 in formulation. Hence, there was no interaction between drug and polymer. 6.2 METRONIDAZOLE MICROSPHERES 6.2.1 Optimization of speed (rpm) for preparation of microspheres Metronidazole microspheres were prepared using emulsion…

I. Abstract The experiment was about using a method of recrystallization to reform benzoic acid and unknown compound, and identifying that compound. The main principle is the polarity and solubility of compound. The compound was dissolved completely with distilled water in hot temperature and reformed back in cold environment. After the experiment, there were up to more than 50% of the compound being recrystallized and the unknown compound had the melting point at 165.2oC. The experiment…

before the filtration process Is because the sucrose would not be pure enough and would have a very low percentage composition due to the fact that it would have many impurities from other components. The impurities will be in the Sucrose because it is insoluble and does not dissolve in DCM. Thoroughly stirring the mixture is required before filtration to make sure all the other components are dissolved in DCM excluding the Sucrose. So initially, the Solid here which is Sucrose will remain…

Introduction: Hot packs work by dissolving a salt, such as calcium chloride, in water to create an exothermic reaction. When salts are dissolved in water it requires energy to break their bonds apart, but energy is also released when the ions are surrounded by the water molecules. If more energy is released than is required to break the bonds, the reaction will be exothermic and will produce heat. In hot packs the water is kept separate from the salt, and when it needs to be activated, they are…

DEVIATION BACKGROUND: On 07/28/2017, During the inspection of PRODUCT A on TP- 18, while the operator was transferring the coated tablets into a plastic scoop, which is used to load the coated tablets into the printer product hopper during the printing, what appeared to be a live and small gnat fly was observed inside the product bag. This was discovered after the operator pulled the product liner off the coated drum to pour the remaining tablets into the scoop. Per routine procedure, during…

We all know that we have our own unique fingerprints but did you know that you can make sun prints? You may be wondering what a sunprint is, a sunprint is like a unique type of photo made with special sunprint paper that with the help of the sun creates a permanent image. A sunprint is formed when a chemical reaction happens with chemicals inside the paper,but before we talk about that, here is how you make a sunprint. You can make a sunprint by placing an object on a sheet of sunprint paper,…

This experiment was performed at the University of Louisiana at Lafayette campus on March 7, 2017. Pots were prepared using 30 0.95-liter black plastic pots. Each pot was labelled sequentially from 1 to 30 along with the soil treatment it would receive, either 100% vermiculite or 90% vermiculite, and the planting density, either 1, 2, 4, 8, or 16 seeds planted. The 100% vermiculite soil treatment was then prepared by using a clean 0.95-liter black plastic pot and adding 15 pots of vermiculite to…

Examined T. californicus ability to handle high temperature stress under short-term, small exposure to high temperature, and long-term, persistant exposure to constant high temperatures. The took populations of T. californicus from 11 pools at different latitudinal gradients in a local scale. They put the specimen in petri dishes with founding adult females. They only mate one time and store the sperm so they can produce many groups of offspring. To test if inbreeding could influence the…