Physical chemistry

The salts and molecules both shared characteristics of white, small crystal like, and all of them had pretty small structures. Although they had physical similarities, we knew that these were different in some type of way. Although our basic observation may be that they would have similar results in most of these tests, there was some distinct differences in the way they are bonded. These bonds although…

The unique composition and purity of as-deposited SnS2 thin films prepared with different precursor solution volumes from 5 ml to 25ml were determined by EDX analysis as shown in fig 5, which brought out the presence of Tin and Sulfur as elementary components. Two different peaks were observed in the spectrums from fig 5 relevant to the tin and sulfur. The EDX spectra show that the weight percentage for the film prepared at the precursor solution volume of 5 ml is 36.8% and 63.2%, which is…

Table 1: Experimental data for standardization of iodine solution. Calculation of standardization factor Standardization factor = (mass of vitamin C titrated) / (Volume of iodine solution used) = (125g) / (41.3ml) = 3.03 mg vitamin C/ml iodine solution Experiment B: Vitamin C titration using fresh fruit sample to determine the content The tabulated experimental data for this experiment is shown below (Table 2). In this experiment, the amount of vitamin C was calculated by multiplying…

What is Styrofoam? Styrofoam is a brand of closed-cell extruded polystyrene foam currently created for thermal insulation and craft applications. Dow Chemical Company retained and produced the Styrofoam. Through petroleum product known as styrene, Styrofoam was created. The styrene is amended into a clear molten mass of polystyrene through a complex chemical process known as polymerization. It would become a hard plastic if it were left to cool. Disposable eating utensils are created from this…

Background : Stoichiometry is the relationship between the relative quantities of substances taking part in a reaction or forming a compound, typically a ratio of whole integers. In the lab that I did with my group we used stoichiometry to find out the decomposition of sodium biocarbonate. Sodium carbonate is just another name for baking soda, and that is what we used on our lab. Baking soda is also used in some food items, such as pancakes, waffles etc… When the baking soda is being heated…

Magnesium Alloy: Microstructure Characteristics: Fig (8) : Shows the microstructure of Magnesium alloy. Picture source: http://www.omicsonline.org/JMSTimages/2155-9589-2-114-g001.html Magnesium alloys have a hexagonal lattice structure. They are the lightest of all structural metals. Magnesium alloys possess a low galling tendency as a bearing surface in conjunction with shaft hardness above 400…

Results The results obtained were statistically analyzed using the Fishers exact test. Table 1: Comparison of microbial growth between different groups Sodium Hypochloride Total Fishers exact test Endovac Laser Control p-value No Growth 5(50.0%) 8(80.0%) 0 15(37.5%) <0.001* <103 5(50.0%) 2(20.0%) 0 7(17.5%) 103 – 108 0 0 0 8(20.0%) >108 0 0 10(100.0%) 10(25.0%) Total 10 10 10 40(100.0%) *p<0.05 statistically significant p>0.05 non significant, NS Amongst the 10…

B.Result and discussion Percentage air voids On the replacement of cupola slag we obtained the result that, on the percentages of 10, 20, 30 and 40 we have the Va values of 4.8, 4, 4.8 and 3.2 % which satisfies the morsth requirement of 3-5% and further we observed that the gradual decrease in the Va values up to 100%. So that for Va the replacement of cupola slag up to 40 % will satisfies the morsth requirement. Percentage of voids in mineral aggregate On the replacement of cupola slag we…

ABSTRACT The reactivity of acid base cements forming hydroxyapatite (HA) such as, β-tricalcium phosphate (β-TCP) and dicalcium phosphate dehydrate (DCPD). Amorphous calcium phosphates, prepared by precipitation from supersaturated solutions, can also react to form apatitic cements since they are thermodynamic unstable with respect to HA and have a setting reaction more independent of particle size. Calcium phosphate cement containing an antibiotic can be used for filling bone defects and to…

Abstract: The purpose of this experiment was to prepare and standardize a sodium hydroxide solution as well as determine the molar concentration in as strong acid and the percent by mass of acetic acid in vinegar. We used volumetric analysis, also known as titration, in both experiments. The average molar concentration for NaOH was 0.2749 mol/L while the average molar concentration of the acid solution was .2493 mol/L.The average percent by mass of acetic acid in vinegar was found to be 12.3 %…