Oxygen therapy

INTRODUCTION Chemically and thermodynamically foam is an unstable, dispersed system of entrapment of gaseous molecules in solid or liquid matter. Instability of foam is caused generally due to coalescence, liquid drainage and disproportion of bubbles. Foam being aqueous system can be produced using surfactants available commercially. The types of surfactants used in preparation of aqueous foam influence the foam properties (Eisner et al., 2007; Bhakta and Ruckenstein, 1995). Successful foam…

Facts about Tech Diving You Should Know The conventional limit exceeded by the form of scuba diving specially the recreational diving’s bottom time and depth is known as tech diving. It is also known as Technical Diving. The Technical and Recreational Scuba Diving can be distinguished with lots of differences. According to many people, there are not any obvious differences between Tech and Recreational Diving. They think that ‘diving is diving’ and it is useless to divide it into different types…

• What is means of welding? The welding is the processes which make the permanent bonding between the two or more solid bodies o the metal if the welding is not done properly the welding joint can be brake from the welding place and if the welding is done properly the metal can be brake from the middle or the center of the object • Spot welding http://www.taylorautobody.com/Portals/16/images/Pro%20Spot%202.jpg There is many type of welding processes 1 Gas welding 2 Gas shielded arc welding 3…

Intermolecular Forces Intermolecular forces are the result of attractive or repulsive forces between atoms, molecules or ions, primarily as a result of electrostatic attractions; these forces act between discrete molecules. Intermolecular forces are weak forces but without them life as we know it would not be possible: water vapor would not condense into its liquid (or solid forms) if its molecules did not attract each other, and all matter, in fact, would exist as gases. The physical states…

UVB’s 1. The sun shines on the skin. 2. The UVB light interfaces with a form of cholesterol in the skin called 97-dehydrocholesterol. 3. This is synthesized into pre-vitamin D3, which is immediately converted into vitamin D3. 30 minutes of midday sun in a bathing suit, and you’ve absorbed up to 20,000 IU of vitamin D. Whether you spend half an hour in the midday sun or take 2 10,000 IU of vitamin D3 in tablets, it’s then transported to the liver where it’s turned into D25 for storage. These…

According to R.A Aitken, “An asymmetric synthesis may be defined as a synthesis in which an achiral unit is an ensemble of substrate molecules is converted to a chiral unit such that the possible stereoisomers are formed in unequal amounts.” It relates to any synthetic process that incorporates one or more new elements of chirality during a functional group transformation. Asymmetric synthesis involves the formation of chiral molecules. An object is said to be chiral, if it cannot be…

TRIS Hcl, NBT, NADH, Ethanol, PMS, l-ascorbic acid 1. The superoxide radicals is generated in 3 ml of TrisHCl buffer (16 mM, pH 8.0) containing 1 ml of NBT (50 μM), 1 ml NADH (78 μM) and ethanol extract of sample (25 – 50 μg). 2. The reaction was started by adding 1 ml of PMS solution (10 μM) to the mixture. 3. The reaction mixture was incubated at 25° C for 5 min, the absorbance was read at 560 nm using a spectrophotometer (Schimadzu UV-Vis 1700) against blank samples using l- ascorbic acid…

Salts and molecules have similar characteristics, and many differences whether we can tell by first looks or not. Testing these two only supports the differences, and many structural functions cause these differences. Since salts are ionically bonded, they have different properties and functions compared to the covalent bonded molecules. Salts have a ionic bond, and we can confirm due to their electronegativity. As you move from left to right on the periodic table you would notice that…

though it is called stainless steel, it is not entirely stainless, because in low-oxygen, high salinity environments it is able to be stained. The main difference between stainless steel and general carbon steel is the amount of chromium present. Due to the amount of chromium that stainless steel contains, the stainless steel will form a chromium oxide film which will help prevent corrosion as it blocks the oxygen fusing to the surface of the steel and in turn blocks it from spreading to the…

The unique composition and purity of as-deposited SnS2 thin films prepared with different precursor solution volumes from 5 ml to 25ml were determined by EDX analysis as shown in fig 5, which brought out the presence of Tin and Sulfur as elementary components. Two different peaks were observed in the spectrums from fig 5 relevant to the tin and sulfur. The EDX spectra show that the weight percentage for the film prepared at the precursor solution volume of 5 ml is 36.8% and 63.2%, which is…