Military base

Abstract: The purpose of this experiment was to prepare and standardize a sodium hydroxide solution as well as determine the molar concentration in as strong acid and the percent by mass of acetic acid in vinegar. We used volumetric analysis, also known as titration, in both experiments. The average molar concentration for NaOH was 0.2749 mol/L while the average molar concentration of the acid solution was .2493 mol/L.The average percent by mass of acetic acid in vinegar was found to be 12.3 %…

The % relative standard deviation (% RSD) was found to be below 5 % for all the four analytes in system precision and below 6 % in method precision. The data as shown in Table 3.4.3.3.3 and 3.4.3.3.4. LOD values observed for Hydrazine carbamate and Hydrazone carbamate were 0.0018 µg per mL and 0.00092 µg per mL respectively. The LOD value observed for both 1-Hydroxy benzotriazole and 2R, 3S Chlorohydrine hydrochloride were 0.0019 µg per mL. The LOQ values observed for all four analytes were…

Effect of Organic Solvents on Particle Size When anti solvent was 0.4% (w/v) F68 aqueous solution, the effect of various good solvent was investigated. These organic solvents include ethanol, methanol, PEG 400, propylene glycol. The result as mention in Table 16 & Figure 27 showed that the particles prepared by methanol were the smallest (317 nm) among other organic solvents. Ethanol, PEG 400, and propylene glycol produced the particles having the mean particle size of 525nm, 1274nm, 864nm,…

Acid Base Balance Study Guide Definition: The body’s ability to regulate and compensate for variances of the acidity or alkalinity of body fluids through mechanisms in the brain, kidneys, lungs, and buffering system. Concept Key Terms: • Acid: any substance that has a pH less than 7.0 • Acidosis: the condition of having too much acid build up in body fluids, below 7.35 • Alkalosis: the condition of having too much alkaline build up in body fluids, above 7.45 • Anion: a negatively charge…

Fig 4.12 shows the comparison of product density of hydrotreated GO obtained using CAT-E and CAT-C. The density of hydrotreated GO from CAT-C at 370◦C was 0.8148g/ml whereas at the same temperature the density of hydrotreated GO obtained from CAT-E was 0.8302 g/ml despite sulphur and nitrogen in the GO has been reduced to less than 50 ppm and 1 ppm respectively. The reason for higher density would be due to higher aromatic content in the hydrotreated product obtained from CAT-E. This indicates…

The purpose and objective of this experiment was to determine the percent by mass of acetic acid within a sample of vinegar using volumetric analysis with the titration technique. The theory is that if the volume and molar concentration of the standardized sodium hydroxide (NaOH) solution is known, then the percent by mass of the acetic acid (CH3COOH) in vinegar can be calculated after a titration.1 Within this experiment, a NaOH solution was standardized with a primary standard acid of…

One of the parameters that determines water quality is pH. It is defined as the negative logarithm of the hydrogen ion and is intended to be a measurement of the balance of acids and bases. Temperature affects pH. In pure water, a decrease in pH of 0.45 occurs when temperature is increased by 25°C [11]. There are several methods for measuring pH. The most common is the use of a glass electrode sensible to it, a reference electrode and a measurement device. Another method is the use of…

Do mole ratios affect the amount of reactant that is produced? This experiment tested why mixing reactants in different mole ratios affected the amount of the product and the amount of each reactant that is left over. To solve the problem, the lab contained reacting sodium bicarbonate(baking soda) and acetic acid(vinegar) in different ratios and seeing if the product changed. The data suggests that the higher ratio of baking soda to vinegar creates the most product. For the ratio…

differentiate acids and bases? How do we know if a substance is an acid or a base? There are different methods to discover whether a substance is an acid or a base. One of the methods is by using an acid-base indicator or by identifying hydrogen or hydroxide ions in a substance’s chemical formula. Certain materials such as a plastic template, red litmus paper, blue litmus paper, phenolphthalein, universal indicator, and a pH chart can be used to help us distinguish acids and bases. Before…

A clean flame test wire was inserted into 0.2 M NaCl and also placed on the flame reputedly. A bright yellow persistent flame was a positive test of sodium being presented, then repeat the same instructions for the unknown ion. After the flame test wire was clean 0.2M KCl was dipped into the flame resulted a lavender color after several trials as well as the unknown solution. 10 drops of 0.1M Ca(NO3)2 in a test tube and 2-3 drops of 1M Na2C2O4, a white precipitate of calcium was present. The…