Liquid crystal display

The experiment of fluidization in packed column was determined by using air as the conveying media. The fluidized bed is when the air make the solid to behave like a fluid. For this experiment, two columns are use which one column are filled with sand and the other one filled with aluminum oxide. The bed height of aluminum oxide is 100 mm and have a particle size about 250 micron (mesh 60). The minimum fluidization velocity is used to determine the pressure drop. As mentioned above, when the…

3.3 Tribological properties of Cr-B-C-N coatings in artificial seawater Fig.10 shows the friction behaviors and the mean-steady friction coefficients of Cr-B-C-N coatings sliding against SiC balls in artificial seawater. As seen in Fig.10a, it is clear that the CrCN coatings showed higher friction coefficient than other coatings during the tribo-test in artificial seawater. The initial friction coefficient of CrCN coatings was 0.17, while that of CrBCN coatings ranged between 0.14 and 0.15. For…

A water jet cutter, commonly called a water jet, is a tool that uses a very high-pressure jet of water or a mixture of water and an abrasive to cut a wide variety of materials. A water jet that does not use abrasives is referred to as a pure water jet or water-only cutting [1]. For a pure water jet (Figure 1) the water is pressurized to the range of 20 - 94 ksi, 138 - 649 MPa at the inlet and forced through an orifice with a diameter of between 0.25 - 4 mm creating a very thin high velocity…

In our previous report, 21 we investigated the influence of formulation variables of clotrimazole-loaded cubic liquid crystalline nanoparticles. The composition of chitosan tailored cubic nanoparticles was optimized employing central composite design. The findings of Small angle X-ray scattering analysis confirmed the presence of D and P cubic phases in nanoparticles. Most importantly, considerable improvement in mucin binding was observed upon incorporation of chitosan owing to electrostatic…

turning. Lattice turning is utilized for the generation of better fibers. The nylon chips are made to fall on a hot matrix that melts the nylon pieces. The liquid nylon is pumped through a sand channel to the spinneret. The sort of fiber created relies on the quantity of gaps on the spinneret, the size and the state of the gaps. The liquid nylon as expelled from the spinneret sets and structures fibers as presented to the air. Extruder turning is by and large utilized for heavier yarns. The…

Sharpie permanent markers contain n-propanol (C3H8O) n-butanol (C4H10O), and Diacetone alcohol (C6H12O2). These markers are generally used on hard, non-porous surfaces, because instead of damaging the surface they form a surface layer that can be removed easily by solvents such as acetone (C3H6O), xylene (C8H10), or toluene (C7H8). Acetone (strong chemical used in nail polish remover) is a strong and very effective against permanent markers. It can also remove paint and melt certain surfaces.…

The optimum dental treatment for any patient is to restore teeth function and esthetic while removing the least amount of tooth structure, and replacing it with a dental material that will be biocompatible with the tooth and resist the hostile oral environment. Dental materials are incorporated into the teeth structure by retention. This retention can accomplished through mechanical, chemical adhesion or bonding mechanisms between materials and the dental structure. Mechanical retention is…

there. The volume of liquid in the beaker before the egg was placed in was 150 mL, and when the egg was taken out, the volume decreased to 130 mL. This proves that some of the distilled water that was in the beaker passed through the cell membrane and into the egg, which explains why the mass of the mass increased, while the volume of water decreased. The distilled water didn’t have any minerals or gunk that prevented it from going through the cell membrane easily, while the liquid that was in…

If you are looking for ways to reduce your energy bill this winter, you should look into insulating your electric water heater. An uninsulated water heater loses heat, which can impact your overall energy costs, especially during the winter months when it is colder. Here is what you need to do in order to insulate your electric water heater. #1 Clean Your Heater The first thing you need to do is remove any items that you have stored in or around your water heater. You'll want a clear work…

Abstract: The purpose of this lab was to show the different absorption and emission rates of three different substances. Radiation laws, albedo, and specific heat are all reasons why this is achievable. An agreed upon hypothesis is that the sand will absorb the most heat due to the number of molecules, the moss will absorb the second most because it doesn't have as many molecules as sand, but it has more than water, which isn’t as complex. To complete this experiment, you need three beakers of…