Liquid crystal display

All fluids have its resistance to relative motion between surfaces and is called Viscosity. This property is about the friction between the particles of a fluid. A fluid that is forced in a tube has the liquid moving faster as it is closer the axis of the tube and slower when farther from it. 3.1.1 Dimensionless Parameters In analysis of convection heat transfer, it is convenient to convert to non-dimensional the governing equations and combine the variables, which makes the group of…

Friction loss is defined as the pressure loss or head loss that usually occurs in pipeline fluid flow because of the viscosity effect near the surface of the pipe. When the fluid flows along the pipeline, it produces frictional resistance thus results in loss of energy or total head loss of the fluid. Therefore, experiment was conducted to verify the Darcy Weisbach equation by determining the pressure loss along a horizontal pipe. Figure A below shows the diagram of friction loss along a…

Definition: An orifice plate is a device that is used for the measurement of flow rate for reducing pressure or for the restricting flow. An orifice plate is a thin plate with a hole in it, which is usually placed in a pipe. When a fluid (either liquid or gaseous) passes through the orifice, its pressure builds up slightly upstream of the orifice. But as the fluid is forced to converge to pass through the hole, the velocity increases & the fluid pressure decreases. Orifice Plate is the heart of…

4.6 The Selection of the Injection Machine 4.6.1 Calculation of the Injection Volume Figure 4-8 shows the volume of plastic parts by Solidworks modeling. Figure 4-8 Volume of the Stress Cone Plastic parts volume: Vplastic = 4.198 × 10-5 m3 = 41.98 cm3 Plastic parts density: ρ = 1.2 g/cm3 Plastic parts quality: mplastic = ρVplastic = 1.2 × 41.98 = 50.376 g 4.6.2 Preliminary Estimation of the Gating System Although the gating system of condensate cannot determine the exact value prior…

The Evaporation of Liquids When a liquid is left in a warm car over a certain period of time some people might notice that the liquid seems to have lessened. This is because of evaporation, evaporation is when a liquid changes into a gas because of an increase in temperature or pressure. This brings up many questions having to do with liquids and evaporation so, do all liquids take the same amount of time to evaporate? Why do different liquids have…

The Freezing point of water is 32° fahrenheit, But does anything affect the freezing point of water? The effect of salt and sugar lowering water’s freezing point is called Freezing Point Depression(FPD). When water freezes, its molecules slow down and “stick” together, and eventually slow down so much they stay in place and become a solid. However when salt or sugar is added, it “interferes with the formation of the crystalline bonds between water molecules that give ice its solidity”, Written…

which is one minute, and the amount of liquid in each can which is 10 mL. We also had confounding variables which are variables that the researcher failed to control, or eliminate, damaging the internal validity of an experiment. Some confounding variables in our experiment are the temperature in the can when we flip it because we actually couldn’t tell what it was, and the fact that we couldn’t control the fact that there should be exactly 10 mL of the liquid in the can because no matter what…

Mercury is highly toxic to a point where the exposure to less than a gram of liquid mercury can cause mercury poisoning. Mercury has low oxidation, the chemical element has little to no reaction when exposed to oxygen in the air. Mercury in general reacts with acids, the element reacts with some acids that are warm but has no affect to most cold acids. Mercury forms a chemical property called amalgam which is a liquid mercury mixed with metal alloy mixture used to fill cavities caused by tooth…

For the controlled dH2O, it was hypothesized that no disks would float. The reason is because there is not enough CO2 for sample organism to absorb to allow it to do so. Looking at Figure 5.1, the slope of the line is y=0. This supports the hypothesis because there are no floating disks. For the 0.2% bicarbonate solution, it was hypothesized that if the leaf disks in this solution were placed under a lamp, then the disks would float. Figure 5.1 supports this claim, as there is an almost linear…

How to Change Your Oil Frequent oil changes are an important part of routine maintenance (Edmunds). An oil change gets rid of the old oil in the engine by replacing it with new oil (Edmunds). The oil filter is also replaced during this process. The oil filter makes sure the oil circulating through the engine is of good quality. Frequent oil changes are an important step in routine maintenance, because it rids the engine of the old oil by replacing it with new, fresh oil (NAPAFilters). An…